2010 Cadillac Truck SRX FWD V6-3.0L Page 1576

2010 Cadillac Truck SRX FWD V6-3.0L Page 1576

* DTCs P0601, P0602, P0603, P0604, P0606, P062B, P062F, P0630 and P16F3 are Type A DTCs.

* DTC P2610 is a Type B DTC.

Conditions for Clearing the DTC

* DTCs P0601, P0602, P0603, P0604, P0606, P062B, P062F, P0630 and P16F3 are Type A DTCs.

* DTC P2610 is a Type B DTC.

Diagnostic Aids

Low voltage or a momentary loss of power or ground to the ECM may cause a DTC to set. Verify for the following:

* The battery cables are clean and tight, and the battery is fully charged-Refer to Battery Inspection/Test (See: Starting and Charging/Testing

and Inspection/Component Tests and General Diagnostics/Battery Inspection/Test).

* The ECM ground circuits do not have an open or high resistance

* The ECM power circuits do not have an open, short to ground, or high resistance

Reference Information

Schematic Reference

Engine Controls Schematics (LAU) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics

(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

1. Observe the DTC information with a scan tool. DTC P0601, P0602, P0603, P0604, P0606, P062B, P062F, P0630, P16F3, or P2610 should

not set.

2. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Ignition ON, clear the DTC information with a scan tool.

2. Observe the scan tool DTC information. Verify that DTC P0602 or P0630 does not set.

瀚慖f DTC P0602 or P0630 failed this ignition, reprogram the K20 ECM. Refer to Control Module References (See: Testing and

Inspection/Programming and Relearning). If the DTC resets, replace the K20 ECM.

3. Observe the DTC information with a scan tool. Verify that DTC P0601, P0603, P0604, P0606, P062B, P062F, P16F3, or P2610 does not set.

瀚慖f a DTC failed this ignition, replace the K20 ECM.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

Control Module References (See: Testing and Inspection/Programming and Relearning) for engine control module replacement, setup, and

2010 Cadillac Truck SRX FWD V6-3.0L Page 1594

2010 Cadillac Truck SRX FWD V6-3.0L Page 1594

DTC P0601-P0604, P0606, P0607, P0610, P062B, P062F, P0630, P16F3, or P2610 (ECM, LF1/LFW/LWR)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC P0601

- Control Module Read Only Memory Performance

DTC P0602

- Control Module Not Programmed

DTC P0603

- Control Module Long Term Memory Reset

DTC P0604

- Control Module Random Access Memory Performance

DTC P0606

- Control Module Processor Performance

DTC P062B

- Control Module Fuel Injector Control Performance

DTC P062F

- Control Module Long Term Memory Performance

DTC P0630

- VIN Not Programmed or Mismatched - Engine Control Module (ECM)

DTC P16F3

- Control Module Redundant Memory Performance

DTC P2610

- Control Module Ignition Off Timer Performance

Circuit/System Description

This diagnostic applies to internal microprocessor integrity conditions within the engine control module (ECM). This diagnostic also addresses if

the ECM is not programmed, or is programmed incorrectly.

Conditions for Running the DTC

P0601, P062B, P0630, P16F3

These DTCs run continuously when the ignition is ON.

P0602, P0603, P062F

These DTCs run at power up.

P0604

DTC P0604 runs continuously when the ignition is ON. First memory scan may take up to 30 s.

P0606

* System voltage is greater than 6 V.

* Reduced engine power is not active.

* DTC P0606 runs continuously when the above conditions are met.

P2610

* The intake air temperature is between -40 to +80掳C (-40 to +176掳F).

2010 Cadillac CTS Sedan AWD V6-3.6L Page 882

2010 Cadillac CTS Sedan AWD V6-3.6L Page 882

* DTCs P0601, P0602, P0603, P0604, P0606, P062B, P062F, P0630 and P16F3 are Type A DTCs.

* DTC P2610 is a Type B DTC.

* DTCs P0607 and P0610 are Type C DTCs.

Conditions for Clearing the DTC

* DTCs P0601, P0602, P0603, P0604, P0606, P062B, P062F, P0630 and P16F3 are Type A DTCs.

* DTC P2610 is a Type B DTC.

* DTCs P0607 and P0610 are Type C DTCs.

Diagnostic Aids

Verify that the battery cables are clean and tight, and the battery is fully charged. Refer to Battery Inspection/Test (See: Starting and

Charging/Testing and Inspection/Component Tests and General Diagnostics/Battery Inspection/Test).

Reference Information

Schematic Reference

Engine Controls Schematics (LLT) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics

(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit

Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Wiring Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

1. Observe the DTC information with a scan tool. DTC P0601, P0602, P0603, P0604, P0606, P0607, P0610, P062B, P062F, P0630, P16F3, or

P2610 should not set.

2. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Test the voltage and ground inputs to the K20 ECM for the following:

* A short

* An open

* High resistance

2. Ignition ON, observe the DTC information with a scan tool.

瀚慖f DTC P0602, P0610, or P0630 failed this ignition, program the K20 ECM. If the DTC resets, replace the K20 ECM.

3. Observe the DTC information with a scan tool. DTC P0601, P0603, P0604, P0606, P0607, P062B, P062F, P16F3, or P2610 should not set.

瀚慖f a DTC failed this ignition, replace the K20 ECM.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

Control Module References (See: Testing and Inspection/Programming and Relearning) for engine control module replacement, setup, and

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2186

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2186

DTCs P0601, P0602, P0603, P0604, P0606, P060B and P062F are Type A DTCs.

Diagnostic Aids

When attempting to set transmission control module internal DTCs, run the engine for at least 1 minute, and then shut the engine off for 30

seconds. Following this procedure will allow for a complete transmission control module shutdown.

Reference Information

Schematic Reference

Automatic Transmission Controls Schematics (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Diagrams)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Circuit/System Verification

Verify that DTC P0601, P0602, P0603, P0604, P0606, P060B, or P062F is not set.

If the DTC is set, program the Q8 control solenoid valve assembly. If the DTC resets, replace the Q8 control solenoid valve assembly.

Component Testing

Perform the Control Solenoid Valve and Transmission Control Module Assembly Inspection (See: Transmission and Drivetrain/Automatic

Transmission/Transaxle/Testing and Inspection/Component Tests and General Diagnostics/2ML70 - Automatic Transmission/Control Solenoid

Valve and Transmission Control Module Assembly Inspection).

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

Control Module References (See: Testing and Inspection/Programming and Relearning) for control solenoid valve assembly replacement, setup,

and programming.

P0607

DTC P0601, P0602, P0603, P0604, P0606, P0607, P060D, P062F, or P2610 (ECM)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each of the diagnostic category.

DTC Descriptors

DTC P0601

- Control Module Read Only Memory Performance

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1999

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1999

P0220, P0222, P0223, P0335, P0336, P0606, P0641, P0651, P1516, P2101, P2120, P2122, P2123, P2125, P2127, P2128, P2135, P2138, and

P2176 are not set.

* When DTC P0315 is set, the engine speed must be more than 1,000 RPM.

* Engine run time is more than 2 crankshaft revolutions.

* The engine speed is between 375-5,600 RPM.

* The ignition voltage is between 9-18 volts.

* The engine coolant temperature (ECT) is between -7 and +130掳C (+19 and +266掳F).

* When the startup ECT is colder than -7掳C (+19掳F), this diagnostic will be delayed until the ECT is warmer than +21掳C (+69掳F).

* The fuel level is more than 10 percent.

* The ECM is not in fuel shut-off, or decel fuel cut-off mode.

* The electronic brake control module (EBCM) and the traction control system (TCS) are not active or detecting rough road.

* An automatic transmission shift with a throttle position more than 95 percent is not occuring.

* The power management is not active.

* Excessive drive wheel slip is not detected.

* The power take-off (PTO) is disabled, where applicable.

* The cylinder deactivation is not in progress, where applicable.

* DTCs P0300-P0308 run continuously when the above conditions are met.

Conditions for Setting the DTC

DTC P0300

The ECM is detecting a crankshaft speed change indicating a random misfire is occuring that exceeds mandated emission level standards or is at

catalytic converter damaging levels.

DTC P0301, P0302, P0303, P0304, P0305, P0306, P0307, or P0308

The ECM is detecting a crankshaft speed change indicating a single cylinder misfire is occuring that exceeds mandated emission level standards or

is at catalytic converter damaging levels.

Action Taken When the DTC Sets

* DTCs P0300-P0308 are Type B DTCs.

* When the MIL is flashing the fuel injector may be disabled for the misfiring cylinder to protect the catalytic converter.

* Depending on the conditions that set the DTC, the engine may go into Open Loop.

Conditions for Clearing the MIL/DTC

* DTCs P0300-P0308 are Type B DTCs.

* The DTC must run and pass under the same operating conditions that were present when the DTC failed.

Diagnostic Aids

* Ensure that each fuel injector is connected to the proper fuel injector harness connector.

* A misfire may only occur when the engine is operating under a load or when the engine is cold.

* A high resistance condition on any ignition control (IC) circuit can cause an engine misfire P0300-P0308 DTC to set without setting an IC

circuit P0351-P0358 DTC.

* This test procedure requires that the vehicle battery has passed a load test and is completely charged. Refer to Battery Inspection/Test (See:

Starting and Charging/Testing and Inspection/Component Tests and General Diagnostics/Battery Inspection/Test).

* A misfire DTC could be caused by an excessive vibration from sources other than the engine. Inspect the following for possible sources of

vibration:

- A tire or wheel that is out of round or balance

- Variable thickness brake rotors

- An unbalanced drive shaft

- Certain rough road conditions

- A damaged accessory drive component or belt

- A damaged reluctor wheel

- The Crankshaft Position System Variation Learn procedure may need to be performed.

Reference Information

Schematic Reference

Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

2010 Cadillac Truck SRX AWD V6-3.0L Page 1087

2010 Cadillac Truck SRX AWD V6-3.0L Page 1087

DTC P0601-P0604, P0606, P0607, P0610, P062B, P062F, P0630, P16F3, or P2610 (ECM, LF1/LFW/LWR)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC P0601

- Control Module Read Only Memory Performance

DTC P0602

- Control Module Not Programmed

DTC P0603

- Control Module Long Term Memory Reset

DTC P0604

- Control Module Random Access Memory Performance

DTC P0606

- Control Module Processor Performance

DTC P062B

- Control Module Fuel Injector Control Performance

DTC P062F

- Control Module Long Term Memory Performance

DTC P0630

- VIN Not Programmed or Mismatched - Engine Control Module (ECM)

DTC P16F3

- Control Module Redundant Memory Performance

DTC P2610

- Control Module Ignition Off Timer Performance

Circuit/System Description

This diagnostic applies to internal microprocessor integrity conditions within the engine control module (ECM). This diagnostic also addresses if

the ECM is not programmed, or is programmed incorrectly.

Conditions for Running the DTC

P0601, P062B, P0630, P16F3

These DTCs run continuously when the ignition is ON.

P0602, P0603, P062F

These DTCs run at power up.

P0604

DTC P0604 runs continuously when the ignition is ON. First memory scan may take up to 30 s.

P0606

* System voltage is greater than 6 V.

* Reduced engine power is not active.

* DTC P0606 runs continuously when the above conditions are met.

P2610

* The intake air temperature is between -40 to +80掳C (-40 to +176掳F).

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1720

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1720

1. Observe the DTC information with a scan tool. DTC P0601, P0602, P0603, P0604, P0606, P0607, P060D, P062F, or P2610 should not set.

2. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Observe the DTC information with a scan tool.

瀚慖f DTC P0602 is set, attempt to program the K20 ECM before replacing the K20 ECM. Refer to Control Module References (See:

Testing and Inspection/Programming and Relearning) for K20 ECM replacement, setup, and programming.

瀚慖f DTC P0602 resets, replace the K20 ECM.

2. Observe the DTC information with a scan tool. DTC P0601, P0603, P0604, P0605, P0606, P0607, P060D, P062F, or P2610 should not set.

瀚慖f a DTC failed this ignition, replace the K20 ECM.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, programming and setup

Fuel Pump Control Module

DTC P0601-P0604, P0606, or P062F

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions)provides an overview of each diagnostic category.

DTC Descriptors

DTC P0601

- Control Module Read Only Memory (ROM)

DTC P0602

- Control Module Not Programmed

DTC P0603

- Control Module Long Term Memory Reset

DTC P0604

- Control Module Random Access Memory (RAM)

DTC P0606

- Control Module Internal Performance

DTC P062F

- Control Module Long Term Memory Performance

Circuit/System Description

The internal fault detection is handled inside the fuel pump control module. No external circuits are involved.

Conditions for Running the DTC

The fuel pump control module runs the program to detect an internal fault when power up is commanded. The only requirements are voltage and

ground. This program runs even if the voltage is out of the valid operating range.

Conditions for Setting the DTC

The fuel pump control module has detected an internal malfunction.

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1714

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1714

P0606, P0607, P060D

* The ignition switch is in Run or Crank.

* The system voltage is more than 6.0 V.

* Reduced Engine Power is not active.

* These DTCs run continuously when the above conditions are met.

P2610

* The intake air temperature is between -40 to +125掳C (-40 to +257掳F).

* DTC P2610 runs once per ignition cycle on ECM power down.

Conditions for Setting the DTCs

The ECM detects an internal failure or incomplete programming for more than 10 s.

Actions Taken When the DTC Sets

* DTCs P0601, P0602, P0603, P0604, P0606, P060D, and P062F are Type A DTCs.

* DTC P0607 is a Type C DTC.

* DTC P2610 is a Type B DTC.

Conditions for Clearing the MIL/DTC

* DTCs P0601, P0602, P0603, P0604, P0606, P060D, and P062F are Type A DTCs.

* DTC P0607 is a Type C DTC.

* DTC P2610 is a Type B DTC.

Diagnostic Aids

Low voltage or a momentary loss of power or ground to the ECM may cause a DTC to set.

* Verify that the battery cables are clean and tight, and the battery is fully charged. Refer to Battery Inspection/Test (See: Starting and

Charging/Testing and Inspection/Component Tests and General Diagnostics/Battery Inspection/Test).

* Verify the ECM ground circuits do not have an open or high resistance.

* Verify the ECM power circuits do not have an open, short to ground, or high resistance.

Reference Information

Schematic Reference

Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

1. Observe the DTC information with a scan tool. DTC P0601, P0602, P0603, P0604, P0606, P0607, P060D, P062F, or P2610 should not set.

2. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

2010 Cadillac Truck Escalade RWD V8-6.2L Page 2186

2010 Cadillac Truck Escalade RWD V8-6.2L Page 2186

DTCs P0601, P0602, P0603, P0604, P0606, P060B and P062F are Type A DTCs.

Diagnostic Aids

When attempting to set transmission control module internal DTCs, run the engine for at least 1 minute, and then shut the engine off for 30

seconds. Following this procedure will allow for a complete transmission control module shutdown.

Reference Information

Schematic Reference

Automatic Transmission Controls Schematics (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Diagrams)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Circuit/System Verification

Verify that DTC P0601, P0602, P0603, P0604, P0606, P060B, or P062F is not set.

If the DTC is set, program the Q8 control solenoid valve assembly. If the DTC resets, replace the Q8 control solenoid valve assembly.

Component Testing

Perform the Control Solenoid Valve and Transmission Control Module Assembly Inspection (See: Transmission and Drivetrain/Automatic

Transmission/Transaxle/Testing and Inspection/Component Tests and General Diagnostics/2ML70 - Automatic Transmission/Control Solenoid

Valve and Transmission Control Module Assembly Inspection).

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

Control Module References (See: Testing and Inspection/Programming and Relearning) for control solenoid valve assembly replacement, setup,

and programming.

P0607

DTC P0601, P0602, P0603, P0604, P0606, P0607, P060D, P062F, or P2610 (ECM)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each of the diagnostic category.

DTC Descriptors

DTC P0601

- Control Module Read Only Memory Performance

2010 Cadillac Truck Escalade RWD V8-6.2L Page 1999

2010 Cadillac Truck Escalade RWD V8-6.2L Page 1999

P0220, P0222, P0223, P0335, P0336, P0606, P0641, P0651, P1516, P2101, P2120, P2122, P2123, P2125, P2127, P2128, P2135, P2138, and

P2176 are not set.

* When DTC P0315 is set, the engine speed must be more than 1,000 RPM.

* Engine run time is more than 2 crankshaft revolutions.

* The engine speed is between 375-5,600 RPM.

* The ignition voltage is between 9-18 volts.

* The engine coolant temperature (ECT) is between -7 and +130掳C (+19 and +266掳F).

* When the startup ECT is colder than -7掳C (+19掳F), this diagnostic will be delayed until the ECT is warmer than +21掳C (+69掳F).

* The fuel level is more than 10 percent.

* The ECM is not in fuel shut-off, or decel fuel cut-off mode.

* The electronic brake control module (EBCM) and the traction control system (TCS) are not active or detecting rough road.

* An automatic transmission shift with a throttle position more than 95 percent is not occuring.

* The power management is not active.

* Excessive drive wheel slip is not detected.

* The power take-off (PTO) is disabled, where applicable.

* The cylinder deactivation is not in progress, where applicable.

* DTCs P0300-P0308 run continuously when the above conditions are met.

Conditions for Setting the DTC

DTC P0300

The ECM is detecting a crankshaft speed change indicating a random misfire is occuring that exceeds mandated emission level standards or is at

catalytic converter damaging levels.

DTC P0301, P0302, P0303, P0304, P0305, P0306, P0307, or P0308

The ECM is detecting a crankshaft speed change indicating a single cylinder misfire is occuring that exceeds mandated emission level standards or

is at catalytic converter damaging levels.

Action Taken When the DTC Sets

* DTCs P0300-P0308 are Type B DTCs.

* When the MIL is flashing the fuel injector may be disabled for the misfiring cylinder to protect the catalytic converter.

* Depending on the conditions that set the DTC, the engine may go into Open Loop.

Conditions for Clearing the MIL/DTC

* DTCs P0300-P0308 are Type B DTCs.

* The DTC must run and pass under the same operating conditions that were present when the DTC failed.

Diagnostic Aids

* Ensure that each fuel injector is connected to the proper fuel injector harness connector.

* A misfire may only occur when the engine is operating under a load or when the engine is cold.

* A high resistance condition on any ignition control (IC) circuit can cause an engine misfire P0300-P0308 DTC to set without setting an IC

circuit P0351-P0358 DTC.

* This test procedure requires that the vehicle battery has passed a load test and is completely charged. Refer to Battery Inspection/Test (See:

Starting and Charging/Testing and Inspection/Component Tests and General Diagnostics/Battery Inspection/Test).

* A misfire DTC could be caused by an excessive vibration from sources other than the engine. Inspect the following for possible sources of

vibration:

- A tire or wheel that is out of round or balance

- Variable thickness brake rotors

- An unbalanced drive shaft

- Certain rough road conditions

- A damaged accessory drive component or belt

- A damaged reluctor wheel

- The Crankshaft Position System Variation Learn procedure may need to be performed.

Reference Information

Schematic Reference

Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

2010 Cadillac Truck Escalade RWD V8-6.2L Page 1720

2010 Cadillac Truck Escalade RWD V8-6.2L Page 1720

1. Observe the DTC information with a scan tool. DTC P0601, P0602, P0603, P0604, P0606, P0607, P060D, P062F, or P2610 should not set.

2. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Observe the DTC information with a scan tool.

瀚慖f DTC P0602 is set, attempt to program the K20 ECM before replacing the K20 ECM. Refer to Control Module References (See:

Testing and Inspection/Programming and Relearning) for K20 ECM replacement, setup, and programming.

瀚慖f DTC P0602 resets, replace the K20 ECM.

2. Observe the DTC information with a scan tool. DTC P0601, P0603, P0604, P0605, P0606, P0607, P060D, P062F, or P2610 should not set.

瀚慖f a DTC failed this ignition, replace the K20 ECM.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, programming and setup

Fuel Pump Control Module

DTC P0601-P0604, P0606, or P062F

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions)provides an overview of each diagnostic category.

DTC Descriptors

DTC P0601

- Control Module Read Only Memory (ROM)

DTC P0602

- Control Module Not Programmed

DTC P0603

- Control Module Long Term Memory Reset

DTC P0604

- Control Module Random Access Memory (RAM)

DTC P0606

- Control Module Internal Performance

DTC P062F

- Control Module Long Term Memory Performance

Circuit/System Description

The internal fault detection is handled inside the fuel pump control module. No external circuits are involved.

Conditions for Running the DTC

The fuel pump control module runs the program to detect an internal fault when power up is commanded. The only requirements are voltage and

ground. This program runs even if the voltage is out of the valid operating range.

Conditions for Setting the DTC

The fuel pump control module has detected an internal malfunction.

2010 Cadillac Truck Escalade RWD V8-6.2L Page 1714

2010 Cadillac Truck Escalade RWD V8-6.2L Page 1714

P0606, P0607, P060D

* The ignition switch is in Run or Crank.

* The system voltage is more than 6.0 V.

* Reduced Engine Power is not active.

* These DTCs run continuously when the above conditions are met.

P2610

* The intake air temperature is between -40 to +125掳C (-40 to +257掳F).

* DTC P2610 runs once per ignition cycle on ECM power down.

Conditions for Setting the DTCs

The ECM detects an internal failure or incomplete programming for more than 10 s.

Actions Taken When the DTC Sets

* DTCs P0601, P0602, P0603, P0604, P0606, P060D, and P062F are Type A DTCs.

* DTC P0607 is a Type C DTC.

* DTC P2610 is a Type B DTC.

Conditions for Clearing the MIL/DTC

* DTCs P0601, P0602, P0603, P0604, P0606, P060D, and P062F are Type A DTCs.

* DTC P0607 is a Type C DTC.

* DTC P2610 is a Type B DTC.

Diagnostic Aids

Low voltage or a momentary loss of power or ground to the ECM may cause a DTC to set.

* Verify that the battery cables are clean and tight, and the battery is fully charged. Refer to Battery Inspection/Test (See: Starting and

Charging/Testing and Inspection/Component Tests and General Diagnostics/Battery Inspection/Test).

* Verify the ECM ground circuits do not have an open or high resistance.

* Verify the ECM power circuits do not have an open, short to ground, or high resistance.

Reference Information

Schematic Reference

Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

1. Observe the DTC information with a scan tool. DTC P0601, P0602, P0603, P0604, P0606, P0607, P060D, P062F, or P2610 should not set.

2. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 2527

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 2527

DTCs P0601, P0602, P0603, P0604, P0606, P060B and P062F are Type A DTCs.

Diagnostic Aids

When attempting to set transmission control module internal DTCs, run the engine for at least 1 minute, and then shut the engine off for 30

seconds. Following this procedure will allow for a complete transmission control module shutdown.

Reference Information

Schematic Reference

Automatic Transmission Controls Schematics (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Diagrams)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Circuit/System Verification

Verify that DTC P0601, P0602, P0603, P0604, P0606, P060B, or P062F is not set.

If the DTC is set, program the Q8 control solenoid valve assembly. If the DTC resets, replace the Q8 control solenoid valve assembly.

Component Testing

Perform the Control Solenoid Valve and Transmission Control Module Assembly Inspection (See: Transmission and Drivetrain/Automatic

Transmission/Transaxle/Testing and Inspection/Component Tests and General Diagnostics/2ML70 - Automatic Transmission/Control Solenoid

Valve and Transmission Control Module Assembly Inspection).

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

Control Module References (See: Testing and Inspection/Programming and Relearning) for control solenoid valve assembly replacement, setup,

and programming.

6L45/6L50/6L80/6L90 - Automatic Transmission

DTC P0601-P0604 or P062F

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

Note: DTCs P0601, P0602, P0603, P0604 or P062F could set in other control modules. Verify the DTCs are set in the transmission control module

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 2515

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 2515

P0606, P0607

* The ignition switch is in Run or Crank positions.

* The system voltage is more than 6.0 V.

* These DTCs run continuously when the above conditions are met.

P060D

* The ignition switch is in Run or Crank.

* The system voltage is more than 6.0 V.

* Reduced engine power is inactive.

* DTCs P2120, P2122, P2123, P2125, P2127, P2128, P2138 are not set.

* DTC P060D runs continuously when the above conditions are met.

P16F3

* The ignition is ON or the engine is operating.

* DTC P16F3 runs continuously when the above condition is met.

P2610

* The intake air temperature is between -40 to +125掳C (-40 to +257掳F).

* DTC P2610 runs on ECM Power Down.

Conditions for Setting the DTC

The ECM detects an internal failure or incomplete programming for more than 10 s.

Actions Taken When the DTC Sets

* DTCs P0601, P0602, P0603, P0604, P0606, P060D, P062F, and P16F3 are Type A DTCs.

* DTC P0607 is a Type C DTC.

* DTC P2610 is a Type B DTC.

Conditions for Clearing the MIL/DTC

* DTCs P0601, P0602, P0603, P0604, P0606, P060D, P062F, and P16F3 are Type A DTCs.

* DTC P0607 is a Type C DTC.

* DTC P2610 is a Type B DTC.

Reference Information

Schematic Reference

Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

1. Ignition OFF, open the hood to disable the Auto-Stop function. Refer to Hybrid Modes of Operation Description ( See: Hybrid Drive

Systems/Description and Operation/Hybrid Modes of Operation).

2. Ignition ON, verify the scan tool hood position parameter displays Open.

瀚慖f the hood position does not display Open, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1468

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1468

P0606

DTC P0606 runs continuously when the engine speed is greater than 1,200 RPM.

P06D1

* The engine is running.

* The engine speed is less than 5,000 RPM.

* The battery voltage is between 10-18 V.

* DTC P06D1 runs continuously when the above conditions are met.

P2610

DTC P2610 runs continuously when the engine speed is greater than 240 RPM.

Conditions for Setting the DTC

The ECM detects an internal failure or incomplete or incorrect programming.

Action Taken When the DTC Sets

* DTCs P0602, P0603, P0604, P0605, P0606, P0610, P0614, P0630, P160D, and P160E are Type A DTCs.

* DTCs P06D1 and P2610 are Type B DTCs.

* DTC P161C is a Type C DTC.

Conditions for Clearing the DTC

* DTCs P0602, P0603, P0604, P0605, P0606, P0610, P0614, P0630, P160D, and P160E are Type A DTCs.

* DTCs P06D1 and P2610 are Type B DTCs.

* DTC P161C is a Type C DTC.

Diagnostic Aids

Low voltage or a momentary loss of power or ground to the ECM may cause a DTC to set. Verify the following:

* The battery cables are clean and tight, and the battery is fully charged. Refer to Battery Inspection/Test (See: Starting and Charging/Testing

and Inspection/Component Tests and General Diagnostics/Battery Inspection/Test).

* The ECM ground circuits do not have an open or high resistance.

* The ECM power circuits do not have an open, short to ground, or high resistance.

Reference Information

Schematic Reference

Engine Controls Schematics (LAU) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics

(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

1. Observe the DTC information with a scan tool. DTC P0602, P0603, P0604, P0605, P0606, P0610, P0614, P0630, P06D1, P160D, P160E,

2010 Cadillac Truck Escalade AWD V8-6.2L Page 2646

DTC P0601, P0602, P0603, P0604, P0606, P0607, P060D, P062F, or P2610 (ECM)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each of the diagnostic category.

DTC Descriptors

DTC P0601

- Control Module Read Only Memory Performance

DTC P0602

- Control Module Not Programmed

DTC P0603

- Control Module Long Term Memory Reset

DTC P0604

- Control Module Random Access Memory Performance

DTC P0606

- Control Module Processor Performance

DTC P0607

- Control Module Performance

DTC P060D

- Control Module Accelerator Pedal (APP) Position System Circuitry Performance

DTC P062F

- Control Module Long Term Memory Performance

DTC P2610

- Control Module Ignition Off Timer Performance

Circuit/System Description

This diagnostic applies to internal microprocessor integrity conditions within the engine control module (ECM) and the throttle actuator control

(TAC) system. This diagnostic also addresses if the ECM is not programmed.

The ECM monitors its ability to read and write to the memory. It also monitors a timing function. The ECM and the TAC processors are used to

monitor the TAC system data. Both processors monitor the other processors data to verify that the indicated APP calculation is correct. The ECM

performs an intrusive test in order to confirm that the APP signals are not shorted together. The ECM accomplishes this by pulling the APP sensor

2 low momentarily and looking for sensor 1 to also be pulled low.

Conditions for Running the DTCs

P0601, P0604

* The ignition switch is in Run or Crank.

* These DTCs run continuously when the above condition is met.

P0602, P0603, P062F

* The ignition switch is in Run or Crank.

* These DTCs run once per ignition cycle.

P0606, P0607, P060D

* The ignition switch is in Run or Crank.

* The system voltage is more than 6.0 V.

* Reduced Engine Power is not active.

* These DTCs run continuously when the above conditions are met.

P2610

* The intake air temperature is between -40 to +125锟斤拷C (-40 to +257锟斤拷F).

* DTC P2610 runs once per ignition cycle on ECM power down.

2010 Cadillac Truck Escalade AWD V8-6.2L Page 2291

DTCs P0601, P0602, P0603, P0604, P0606, P060B and P062F are Type A DTCs.

Diagnostic Aids

When attempting to set transmission control module internal DTCs, run the engine for at least 1 minute, and then shut the engine off for 30

seconds. Following this procedure will allow for a complete transmission control module shutdown.

Reference Information

Schematic Reference

Automatic Transmission Controls Schematics (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Diagrams)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Circuit/System Verification

Verify that DTC P0601, P0602, P0603, P0604, P0606, P060B, or P062F is not set.

If the DTC is set, program the Q8 control solenoid valve assembly. If the DTC resets, replace the Q8 control solenoid valve assembly.

Component Testing

Perform the Control Solenoid Valve and Transmission Control Module Assembly Inspection (See: Transmission and Drivetrain/Automatic

Transmission/Transaxle/Testing and Inspection/Component Tests and General Diagnostics/2ML70 - Automatic Transmission/Control Solenoid

Valve and Transmission Control Module Assembly Inspection).

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

Control Module References (See: Testing and Inspection/Programming and Relearning) for control solenoid valve assembly replacement, setup,

and programming.

P0607

DTC P0601, P0602, P0603, P0604, P0606, P0607, P060D, P062F, or P2610 (ECM)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each of the diagnostic category.

DTC Descriptors

DTC P0601

- Control Module Read Only Memory Performance

2010 Cadillac Truck Escalade AWD V8-6.2L Page 2087

P0220, P0222, P0223, P0335, P0336, P0606, P0641, P0651, P1516, P2101, P2120, P2122, P2123, P2125, P2127, P2128, P2135, P2138, and

P2176 are not set.

* When DTC P0315 is set, the engine speed must be more than 1,000 RPM.

* Engine run time is more than 2 crankshaft revolutions.

* The engine speed is between 375-5,600 RPM.

* The ignition voltage is between 9-18 volts.

* The engine coolant temperature (ECT) is between -7 and +130锟斤拷C (+19 and +266锟斤拷F).

* When the startup ECT is colder than -7锟斤拷C (+19锟斤拷F), this diagnostic will be delayed until the ECT is warmer than +21锟斤拷C (+69锟斤拷F).

* The fuel level is more than 10 percent.

* The ECM is not in fuel shut-off, or decel fuel cut-off mode.

* The electronic brake control module (EBCM) and the traction control system (TCS) are not active or detecting rough road.

* An automatic transmission shift with a throttle position more than 95 percent is not occuring.

* The power management is not active.

* Excessive drive wheel slip is not detected.

* The power take-off (PTO) is disabled, where applicable.

* The cylinder deactivation is not in progress, where applicable.

* DTCs P0300-P0308 run continuously when the above conditions are met.

Conditions for Setting the DTC

DTC P0300

The ECM is detecting a crankshaft speed change indicating a random misfire is occuring that exceeds mandated emission level standards or is at

catalytic converter damaging levels.

DTC P0301, P0302, P0303, P0304, P0305, P0306, P0307, or P0308

The ECM is detecting a crankshaft speed change indicating a single cylinder misfire is occuring that exceeds mandated emission level standards or

is at catalytic converter damaging levels.

Action Taken When the DTC Sets

* DTCs P0300-P0308 are Type B DTCs.

* When the MIL is flashing the fuel injector may be disabled for the misfiring cylinder to protect the catalytic converter.

* Depending on the conditions that set the DTC, the engine may go into Open Loop.

Conditions for Clearing the MIL/DTC

* DTCs P0300-P0308 are Type B DTCs.

* The DTC must run and pass under the same operating conditions that were present when the DTC failed.

Diagnostic Aids

* Ensure that each fuel injector is connected to the proper fuel injector harness connector.

* A misfire may only occur when the engine is operating under a load or when the engine is cold.

* A high resistance condition on any ignition control (IC) circuit can cause an engine misfire P0300-P0308 DTC to set without setting an IC

circuit P0351-P0358 DTC.

* This test procedure requires that the vehicle battery has passed a load test and is completely charged. Refer to Battery Inspection/Test (See:

Starting and Charging/Testing and Inspection/Component Tests and General Diagnostics/Battery Inspection/Test).

* A misfire DTC could be caused by an excessive vibration from sources other than the engine. Inspect the following for possible sources of

vibration:

- A tire or wheel that is out of round or balance

- Variable thickness brake rotors

- An unbalanced drive shaft

- Certain rough road conditions

- A damaged accessory drive component or belt

- A damaged reluctor wheel

- The Crankshaft Position System Variation Learn procedure may need to be performed.

Reference Information

Schematic Reference

Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1821

2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1821

1. Observe the DTC information with a scan tool. DTC P0601, P0602, P0603, P0604, P0606, P0607, P060D, P062F, or P2610 should not set.

2. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Observe the DTC information with a scan tool.

锟斤拷If DTC P0602 is set, attempt to program the K20 ECM before replacing the K20 ECM. Refer to Control Module References (See:

Testing and Inspection/Programming and Relearning) for K20 ECM replacement, setup, and programming.

锟斤拷If DTC P0602 resets, replace the K20 ECM.

2. Observe the DTC information with a scan tool. DTC P0601, P0603, P0604, P0605, P0606, P0607, P060D, P062F, or P2610 should not set.

锟斤拷If a DTC failed this ignition, replace the K20 ECM.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, programming and setup

Fuel Pump Control Module

DTC P0601-P0604, P0606, or P062F

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions)provides an overview of each diagnostic category.

DTC Descriptors

DTC P0601

- Control Module Read Only Memory (ROM)

DTC P0602

- Control Module Not Programmed

DTC P0603

- Control Module Long Term Memory Reset

DTC P0604

- Control Module Random Access Memory (RAM)

DTC P0606

- Control Module Internal Performance

DTC P062F

- Control Module Long Term Memory Performance

Circuit/System Description

The internal fault detection is handled inside the fuel pump control module. No external circuits are involved.

Conditions for Running the DTC

The fuel pump control module runs the program to detect an internal fault when power up is commanded. The only requirements are voltage and

ground. This program runs even if the voltage is out of the valid operating range.

Conditions for Setting the DTC

The fuel pump control module has detected an internal malfunction.

2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1815

2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1815

P0606, P0607, P060D

* The ignition switch is in Run or Crank.

* The system voltage is more than 6.0 V.

* Reduced Engine Power is not active.

* These DTCs run continuously when the above conditions are met.

P2610

* The intake air temperature is between -40 to +125锟斤拷C (-40 to +257锟斤拷F).

* DTC P2610 runs once per ignition cycle on ECM power down.

Conditions for Setting the DTCs

The ECM detects an internal failure or incomplete programming for more than 10 s.

Actions Taken When the DTC Sets

* DTCs P0601, P0602, P0603, P0604, P0606, P060D, and P062F are Type A DTCs.

* DTC P0607 is a Type C DTC.

* DTC P2610 is a Type B DTC.

Conditions for Clearing the MIL/DTC

* DTCs P0601, P0602, P0603, P0604, P0606, P060D, and P062F are Type A DTCs.

* DTC P0607 is a Type C DTC.

* DTC P2610 is a Type B DTC.

Diagnostic Aids

Low voltage or a momentary loss of power or ground to the ECM may cause a DTC to set.

* Verify that the battery cables are clean and tight, and the battery is fully charged. Refer to Battery Inspection/Test (See: Starting and

Charging/Testing and Inspection/Component Tests and General Diagnostics/Battery Inspection/Test).

* Verify the ECM ground circuits do not have an open or high resistance.

* Verify the ECM power circuits do not have an open, short to ground, or high resistance.

Reference Information

Schematic Reference

Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

1. Observe the DTC information with a scan tool. DTC P0601, P0602, P0603, P0604, P0606, P0607, P060D, P062F, or P2610 should not set.

2. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing