2010 Cadillac CTS Sedan AWD V6-3.6L Page 779

2010 Cadillac CTS Sedan AWD V6-3.6L Page 779

P0343, P0346, P0347, P0348, P0366, P0367, P0368, P0391, P0392, P0393, P0521, P0522, P0523, P0638, P2100, P2101, or P2119 is not set.

瀚慖f a DTC is set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code Descriptions/Diagnostic Trouble

Code (DTC) List - Vehicle) for further diagnosis.

2. Engine idling, command the appropriate Camshaft Position Actuator from 0 degrees to 40 degrees and back to zero while observing the

appropriate scan tool Camshaft Position Variance parameters. The Camshaft Position Variance should be less than 2 degrees in each of the

commanded states.

3. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Ignition OFF, disconnect the harness connector at the appropriate Camshaft Position Actuator Solenoid Valve.

2. Ignition ON, load test for B+ between the ignition circuit terminal 1 and ground.

瀚慖f less than the specified range, test the ignition voltage circuit for a short to ground or an open/high resistance. If the circuit tests normal

and the ignition circuit fuse is open, test all the components connected to the ignition circuit and replace as necessary.

Note: Use the J 35616-200 - Test Lamp for this test. If the J 35616-200 - Test Lamp is not available, use a test lamp that measures greater

than 20 ohm.

3. Connect a test lamp between the control circuit terminal 2 and B+.

4. Command the appropriate Camshaft Position Actuator Solenoid Valve ON with a scan tool.

Note: The voltage must be measured at the control side of the circuit.

5. Load test for less than 1 V between the control circuit terminal 2 and ground.

瀚慖f greater than the specified range, test the control circuit for an open/high resistance. If the circuit/connections test normal, replace the

ECM.

6. Remove the Camshaft Position Actuator Solenoid Valve. Verify the following conditions do not exist with the Camshaft Position Actuator

Solenoid Valve:

* Torn, restricted, mis-positioned, or missing screens at the CMP actuator solenoid

* Engine oil leak between the oil sealing lands of the CMP actuator solenoid. Inspect the lands of the CMP actuator solenoid for nicks.

* Oil seepage at the CMP actuator solenoid connector

瀚慖f a condition is found, replace Camshaft Position Actuator Solenoid Valve.

7. Ignition OFF, swap the Camshaft Position Actuator Solenoid Valve with a Camshaft Position Actuator Solenoid Valve that is operating

correctly.

Note: This step is testing the mechanical CMP actuator for the camshaft that set the DTC.

8. Engine idling. Command the appropriate Camshaft Position Actuator from 0 degrees to 40 degrees and back to zero while observing the

appropriate scan tool Camshaft Position Variance parameters. The Camshaft Position Variance should be less than 2 degrees in each of the

commanded states.

瀚慖f greater than the specified value, replace the mechanical camshaft position actuator.

9. If all circuits/connections test normal, test or replace the Camshaft Position Actuator Solenoid Valve.

Component Testing

1. Ignition OFF, disconnect the harness connector at the appropriate Camshaft Position Actuator Solenoid Valve.

2. Test for 7-12 ohm between the control terminal 2 and the ignition terminal 1 of the solenoid.

瀚慖f not within the specified range, replace the Camshaft Position Actuator Solenoid Valve.

3. Test for infinite resistance between each terminal and the solenoid housing.

瀚慖f not the specified value, replace the Camshaft Position Actuator Solenoid Valve.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Camshaft Position Actuator Solenoid Valve Solenoid Replacement - Bank 1 (Right Side) Intake (See: Engine, Cooling and

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1999

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1999

P0220, P0222, P0223, P0335, P0336, P0606, P0641, P0651, P1516, P2101, P2120, P2122, P2123, P2125, P2127, P2128, P2135, P2138, and

P2176 are not set.

* When DTC P0315 is set, the engine speed must be more than 1,000 RPM.

* Engine run time is more than 2 crankshaft revolutions.

* The engine speed is between 375-5,600 RPM.

* The ignition voltage is between 9-18 volts.

* The engine coolant temperature (ECT) is between -7 and +130掳C (+19 and +266掳F).

* When the startup ECT is colder than -7掳C (+19掳F), this diagnostic will be delayed until the ECT is warmer than +21掳C (+69掳F).

* The fuel level is more than 10 percent.

* The ECM is not in fuel shut-off, or decel fuel cut-off mode.

* The electronic brake control module (EBCM) and the traction control system (TCS) are not active or detecting rough road.

* An automatic transmission shift with a throttle position more than 95 percent is not occuring.

* The power management is not active.

* Excessive drive wheel slip is not detected.

* The power take-off (PTO) is disabled, where applicable.

* The cylinder deactivation is not in progress, where applicable.

* DTCs P0300-P0308 run continuously when the above conditions are met.

Conditions for Setting the DTC

DTC P0300

The ECM is detecting a crankshaft speed change indicating a random misfire is occuring that exceeds mandated emission level standards or is at

catalytic converter damaging levels.

DTC P0301, P0302, P0303, P0304, P0305, P0306, P0307, or P0308

The ECM is detecting a crankshaft speed change indicating a single cylinder misfire is occuring that exceeds mandated emission level standards or

is at catalytic converter damaging levels.

Action Taken When the DTC Sets

* DTCs P0300-P0308 are Type B DTCs.

* When the MIL is flashing the fuel injector may be disabled for the misfiring cylinder to protect the catalytic converter.

* Depending on the conditions that set the DTC, the engine may go into Open Loop.

Conditions for Clearing the MIL/DTC

* DTCs P0300-P0308 are Type B DTCs.

* The DTC must run and pass under the same operating conditions that were present when the DTC failed.

Diagnostic Aids

* Ensure that each fuel injector is connected to the proper fuel injector harness connector.

* A misfire may only occur when the engine is operating under a load or when the engine is cold.

* A high resistance condition on any ignition control (IC) circuit can cause an engine misfire P0300-P0308 DTC to set without setting an IC

circuit P0351-P0358 DTC.

* This test procedure requires that the vehicle battery has passed a load test and is completely charged. Refer to Battery Inspection/Test (See:

Starting and Charging/Testing and Inspection/Component Tests and General Diagnostics/Battery Inspection/Test).

* A misfire DTC could be caused by an excessive vibration from sources other than the engine. Inspect the following for possible sources of

vibration:

- A tire or wheel that is out of round or balance

- Variable thickness brake rotors

- An unbalanced drive shaft

- Certain rough road conditions

- A damaged accessory drive component or belt

- A damaged reluctor wheel

- The Crankshaft Position System Variation Learn procedure may need to be performed.

Reference Information

Schematic Reference

Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

2010 Cadillac Truck Escalade RWD V8-6.2L Page 1999

2010 Cadillac Truck Escalade RWD V8-6.2L Page 1999

P0220, P0222, P0223, P0335, P0336, P0606, P0641, P0651, P1516, P2101, P2120, P2122, P2123, P2125, P2127, P2128, P2135, P2138, and

P2176 are not set.

* When DTC P0315 is set, the engine speed must be more than 1,000 RPM.

* Engine run time is more than 2 crankshaft revolutions.

* The engine speed is between 375-5,600 RPM.

* The ignition voltage is between 9-18 volts.

* The engine coolant temperature (ECT) is between -7 and +130掳C (+19 and +266掳F).

* When the startup ECT is colder than -7掳C (+19掳F), this diagnostic will be delayed until the ECT is warmer than +21掳C (+69掳F).

* The fuel level is more than 10 percent.

* The ECM is not in fuel shut-off, or decel fuel cut-off mode.

* The electronic brake control module (EBCM) and the traction control system (TCS) are not active or detecting rough road.

* An automatic transmission shift with a throttle position more than 95 percent is not occuring.

* The power management is not active.

* Excessive drive wheel slip is not detected.

* The power take-off (PTO) is disabled, where applicable.

* The cylinder deactivation is not in progress, where applicable.

* DTCs P0300-P0308 run continuously when the above conditions are met.

Conditions for Setting the DTC

DTC P0300

The ECM is detecting a crankshaft speed change indicating a random misfire is occuring that exceeds mandated emission level standards or is at

catalytic converter damaging levels.

DTC P0301, P0302, P0303, P0304, P0305, P0306, P0307, or P0308

The ECM is detecting a crankshaft speed change indicating a single cylinder misfire is occuring that exceeds mandated emission level standards or

is at catalytic converter damaging levels.

Action Taken When the DTC Sets

* DTCs P0300-P0308 are Type B DTCs.

* When the MIL is flashing the fuel injector may be disabled for the misfiring cylinder to protect the catalytic converter.

* Depending on the conditions that set the DTC, the engine may go into Open Loop.

Conditions for Clearing the MIL/DTC

* DTCs P0300-P0308 are Type B DTCs.

* The DTC must run and pass under the same operating conditions that were present when the DTC failed.

Diagnostic Aids

* Ensure that each fuel injector is connected to the proper fuel injector harness connector.

* A misfire may only occur when the engine is operating under a load or when the engine is cold.

* A high resistance condition on any ignition control (IC) circuit can cause an engine misfire P0300-P0308 DTC to set without setting an IC

circuit P0351-P0358 DTC.

* This test procedure requires that the vehicle battery has passed a load test and is completely charged. Refer to Battery Inspection/Test (See:

Starting and Charging/Testing and Inspection/Component Tests and General Diagnostics/Battery Inspection/Test).

* A misfire DTC could be caused by an excessive vibration from sources other than the engine. Inspect the following for possible sources of

vibration:

- A tire or wheel that is out of round or balance

- Variable thickness brake rotors

- An unbalanced drive shaft

- Certain rough road conditions

- A damaged accessory drive component or belt

- A damaged reluctor wheel

- The Crankshaft Position System Variation Learn procedure may need to be performed.

Reference Information

Schematic Reference

Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

2010 Cadillac CTS Sedan AWD V6-3.6L Page 1850

2010 Cadillac CTS Sedan AWD V6-3.6L Page 1850

DTC P0638, P2100, P2101, or P2119 (Without LF1)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC P0638

- Throttle Actuator Control (TAC) Command Performance

DTC P2100

- Throttle Actuator Control (TAC) Motor Control Circuit

DTC P2101

- Throttle Actuator Position Performance

DTC P2119

- Throttle Closed Position Performance

Diagnostic Fault Information

Circuit/System Description

The engine control module (ECM) controls the throttle valve by applying a varying voltage to the control circuits of the throttle actuator control

(TAC) motor. The ECM monitors the duty cycle that is required to actuate the throttle valve. The ECM monitors the throttle position sensors 1 and

2 to determine the actual throttle valve position.

Conditions for Running the DTCs

P0638 and P2101

* The ignition is ON or the engine is operating.

* The ignition voltage is greater than 7 V.

* Throttle position adaptation is not active.

* DTCs P0638 and P2101 run continuously once the above conditions are met for greater than 5 s.

P2100

* Before the ECM can report DTC P2100 failed, DTC P2101 must run and pass.

* The ignition is ON or the engine is operating.

* DTC P2100 runs continuously once the above conditions are met.

P2119

* DTC P0111, P0112, P0113, P0116, P0117, P0118, P0119, P0700, P2122, P2123, P2127, P2128, or P2138 is not set.

* The ignition is ON.

* The vehicle speed is 0 km/h (0 mph).

* The engine speed is less than 40 RPM.

* The engine coolant temperature (ECT) is 5-100掳C (41-212掳F).

* The intake air temperature (IAT) is 5-143掳C (41-290掳F).

* The ignition voltage is greater than 10 V.

* The accelerator pedal position (APP) is less than 15 percent.

* DTC P2119 runs once per ignition cycle when the above conditions are met for less than 1 second.

Conditions for Setting the DTC

P0638

* The ECM detects that the commanded duty cycle for the range test high is greater than 80 percent.

OR

* The ECM detects that the commanded duty cycle for the range test low is greater than 80 percent.

* Either condition exists for greater than 1 second, or a cumulative of 10 s.

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1820

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1820

P2101

The ECM detects a 4-50 percent difference between the commanded and the actual throttle plate position, dependant upon the rate of commanded

throttle movement. The condition exists for 1 s.

P2102

The ECM detects an overheat condition with the output driver. The condition exists for 1 s.

P2103

The ECM detects an over load condition with the output driver. The condition exists for 1 s.

P2119

The ECM determines that the throttle valve did not return to the rest position within 1 s. The condition exists for greater than 1 s, or a cumulative of

10 s.

Action Taken When the DTC Sets

DTCs P0638, P2100, P2101, P2102, P2103, and P2119 are Type A DTCs.

Conditions for Clearing the DTC

DTCs P0638, P2100, P2101, P2102, P2103, and P2119 are Type A DTCs.

Diagnostic Aids

Inspect for a condition in which the throttle valve may have been held open. For example, ice may have formed in the throttle bore causing the

throttle valve not to close.

Reference Information

Schematic Reference

Engine Controls Schematics (LAU) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics

(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)

Description and Operation

Throttle Actuator Control (TAC) System Description (See: Powertrain Management/Computers and Control Systems/Description and

Operation/Throttle Actuator Control (TAC) System Description)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Special Tools

* EL 34730-405 - Injector Test Lamp

* For equivalent regional tools, refer to Special Tools (See: Powertrain Management/Computers and Control Systems/Tools and Equipment).

Circuit/System Verification

1. Ignition ON, observe the DTC information with a scan tool. Verify DTC P0121, P0122, P0123, P0221, P0222, or P0223 is not set.

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 2782

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 2782

P2101, P2119, P2135, P2176 are not set.

* The engine coolant temperature (ECT) is greater than 60掳C (140掳F).

* The intake air temperature (IAT) is warmer than -40掳C (-40掳F)

* The ignition 1 voltage is between 10-18 volts.

* The fuel level is greater than 10 percent.

* The engine run time is greater than 160 seconds.

* The engine speed is between 1,200-3,000 RPM.

* The barometric (BARO) pressure is greater than 70 kPa.

* The mass airflow (MAF) is between 20-55 g/s.

* The fuel system is in Closed Loop.

* The throttle position (TP) is greater than 5 percent.

* DTC P0133 runs once per drive cycle when the above conditions are met.

P013A P013C, P013E, or P014A

* Before the ECM can report DTC P013A, or P013C failed, DTCs P013E, P014A, P2270, and P2272 must run and pass.

* Before the ECM can report DTC P013E, or P014A failed, DTCs P2270 and P2272 must run and pass.

* DTCs P0030, P0036, P0053, P0054, P0101, P0102, P0103, P0106, P0107, P0108, P0120, P0121, P0122, P0123, P0131, P0132, P0133,

P0134, P0135, P0137, P0138, P013A, P013B, P013E, P013F, P0140, P0141, P0171, P0172, P0201, P0202, P0203, P0204, P0220, P0222,

P0223, P0300, P0442, P0443, P0446, P0449, P0455, P0496, P1133, P1174, P1516, P2101, P2119, P2135, P2176, P2270, P2271, P2A00 are

not set.

* The ignition 1 voltage is between 10-18 volts.

* The learned heater resistance is valid.

* The fuel level is greater than 10 percent.

* The engine run time is equal to or greater than 5 minutes.

* The accelerator pedal (APP) is steady.

* The torque converter clutch (TCC) is applied.

* DTC P013A runs once per ignition cycle, during decel fuel cut-off (DFCO), when the above conditions are met.

P013B P013D, P013F, or P014B

* Before the ECM can report DTC P013B, or P013D failed, DTCs P013A, P013C, P013E, P013F, P014A, P014B, P2270, P2271, P2272, and

P2273 must run and pass.

* Before the ECM can report DTC P013F, or P014B failed, DTCs P013A, P013C, P013E, P014A, P2270, P2271, P2272, and P2273 must run

and pass.

* DTCs P0030, P0036, P0053, P0054, P0101, P0102, P0103, P0106, P0107, P0108, P0120, P0121, P0122, P0123, P0131, P0132, P0133,

P0134, P0135, P0137, P0138, P013A, P013B, P013E, P013F, P0140, P0141, P0171, P0172, P0201, P0202, P0203, P0204, P0220, P0222,

P0223, P0300, P0442, P0443, P0446, P0449, P0455, P0496, P1133, P1174, P1516, P2101, P2119, P2135, P2176, P2270, P2271, P2A00 are

not set.

* The ignition 1 voltage is between 10-18 volts.

* The learned heater resistance is valid.

* The fuel level is greater than 10 percent.

* The engine run time is equal to or greater than 5 minutes.

* DTC P013B runs once per ignition cycle when the above conditions are met.

Conditions for Setting the DTC

P0133 or P0153

* The ECM detects that the HO2S 1 rich-to-lean or lean-to-rich average response time is greater than a calibrated value.

* The DTCs set within 100 seconds when the above condition is met.

P013A or P013C

The ECM detects that the accumulated mass air flow monitored during rich-to-lean transitions between 450-150 mV is greater than 75 grams.

P013B or P013D

The ECM detects that the accumulated mass air flow monitored during lean-to-rich transitions between 350-650 mV is greater than 75 grams.

P013E or P014A

The ECM detects that the O2 sensor voltage has not decreased below 450 mV within 42 grams of accumulated air flow.

P013F or P014B

The ECM detects that the O2 sensor voltage has not increased above 350 mV within 200 grams of accumulated air flow.

P1133 or P1153

* The ECM detects that the HO2S 1 rich-to-lean counts, or the lean-to-rich counts are less than a calibrated value.

* The DTCs set within 100 seconds when the above condition is met.

Action Taken When the DTC Sets

2010 Cadillac Truck Escalade AWD V8-6.2L Page 2622

P1516, P2101, and P2176

* DTCs P1516, P2101, and P2176 are Type A DTCs.

* The control module commands the TAC system to operate in the Reduced Engine Power mode.

* A message center or an indicator displays Reduced Engine Power.

* Under certain conditions, the control module commands the engine OFF.

P2119

* DTC P2119 is a Type C DTC.

* The driver information center, if equipped, may display a message.

Conditions for Clearing the MIL/DTC

* DTCs P1516, P2101, and P2176 are Type A DTCs.

* DTC P2119 is a Type C DTC.

Diagnostic Aids

* If the Throttle Sweep Test is not available on the scan tool, observe the scan tool TAC Motor parameter while performing the following tests:

- Slowly depress the accelerator pedal to WOT and then slowly return the pedal to closed throttle. Repeat the procedure several times.

- Rapidly depress the accelerator pedal from the rest position to the wide open throttle position (WOT) and release pedal. Repeat the

procedure several times.

The TAC Motor parameter should display Enabled. If Disabled is displayed, continue diagnosis in Circuit/System Testing.

* Inspect for a condition in which the throttle valve may have been held open. For example, ice may have formed in the throttle bore causing

the throttle valve not to close.

* A high resistance condition on the throttle position and throttle actuator control circuits could cause a DTC to set.

* A low battery condition may cause a DTC to set.

Reference Information

Schematic Reference

Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Description and Operation

Throttle Actuator Control (TAC) System Description (See: Powertrain Management/Computers and Control Systems/Description and

Operation/Throttle Actuator Control (TAC) System Description)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

Note: A low battery voltage or charging system condition may cause a DTC to set.

1. Ignition ON, observe the DTC information with a scan tool. DTC P0120, P0122, P0123, P0220, P0222, P0223, P0562, P0621, P0622, or

P2135 should not set.

锟斤拷If a DTC sets, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code Descriptions/Diagnostic Trouble

Code (DTC) List - Vehicle) for further diagnosis.

2010 Cadillac Truck Escalade AWD V8-6.2L Page 2087

P0220, P0222, P0223, P0335, P0336, P0606, P0641, P0651, P1516, P2101, P2120, P2122, P2123, P2125, P2127, P2128, P2135, P2138, and

P2176 are not set.

* When DTC P0315 is set, the engine speed must be more than 1,000 RPM.

* Engine run time is more than 2 crankshaft revolutions.

* The engine speed is between 375-5,600 RPM.

* The ignition voltage is between 9-18 volts.

* The engine coolant temperature (ECT) is between -7 and +130锟斤拷C (+19 and +266锟斤拷F).

* When the startup ECT is colder than -7锟斤拷C (+19锟斤拷F), this diagnostic will be delayed until the ECT is warmer than +21锟斤拷C (+69锟斤拷F).

* The fuel level is more than 10 percent.

* The ECM is not in fuel shut-off, or decel fuel cut-off mode.

* The electronic brake control module (EBCM) and the traction control system (TCS) are not active or detecting rough road.

* An automatic transmission shift with a throttle position more than 95 percent is not occuring.

* The power management is not active.

* Excessive drive wheel slip is not detected.

* The power take-off (PTO) is disabled, where applicable.

* The cylinder deactivation is not in progress, where applicable.

* DTCs P0300-P0308 run continuously when the above conditions are met.

Conditions for Setting the DTC

DTC P0300

The ECM is detecting a crankshaft speed change indicating a random misfire is occuring that exceeds mandated emission level standards or is at

catalytic converter damaging levels.

DTC P0301, P0302, P0303, P0304, P0305, P0306, P0307, or P0308

The ECM is detecting a crankshaft speed change indicating a single cylinder misfire is occuring that exceeds mandated emission level standards or

is at catalytic converter damaging levels.

Action Taken When the DTC Sets

* DTCs P0300-P0308 are Type B DTCs.

* When the MIL is flashing the fuel injector may be disabled for the misfiring cylinder to protect the catalytic converter.

* Depending on the conditions that set the DTC, the engine may go into Open Loop.

Conditions for Clearing the MIL/DTC

* DTCs P0300-P0308 are Type B DTCs.

* The DTC must run and pass under the same operating conditions that were present when the DTC failed.

Diagnostic Aids

* Ensure that each fuel injector is connected to the proper fuel injector harness connector.

* A misfire may only occur when the engine is operating under a load or when the engine is cold.

* A high resistance condition on any ignition control (IC) circuit can cause an engine misfire P0300-P0308 DTC to set without setting an IC

circuit P0351-P0358 DTC.

* This test procedure requires that the vehicle battery has passed a load test and is completely charged. Refer to Battery Inspection/Test (See:

Starting and Charging/Testing and Inspection/Component Tests and General Diagnostics/Battery Inspection/Test).

* A misfire DTC could be caused by an excessive vibration from sources other than the engine. Inspect the following for possible sources of

vibration:

- A tire or wheel that is out of round or balance

- Variable thickness brake rotors

- An unbalanced drive shaft

- Certain rough road conditions

- A damaged accessory drive component or belt

- A damaged reluctor wheel

- The Crankshaft Position System Variation Learn procedure may need to be performed.

Reference Information

Schematic Reference

Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit