2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2496
P2122
The ECM detects that the APP sensor 1 voltage is less than 0.46 V for greater than 0.2 s.
P2123
The ECM detects that the APP sensor 1 voltage is greater than 4.75 V for greater than 0.2 s.
P2125
The APP sensor 2 voltage is less than 0.32 V or greater than 2.6 V for greater than 0.2 s.
P2127
The ECM detects that the APP sensor 2 voltage is less than 0.32 V for greater than 0.2 s.
P2128
The ECM detects that the APP sensor 2 voltage is greater than 2.6 V for greater than 0.2 s.
P2138
The voltage difference between APP sensor 1 and APP sensor 2 exceeds a predetermined value for greater than 1 s.
Action Taken When the DTC Sets
* DTCs P2120, P2122, P2123, P2125, P2127, P2128, and P2138 are Type A DTCs.
* The control module commands the TAC system to operate in the Reduced Engine Power mode.
* A message center or an indicator displays Reduced Engine Power.
* Under certain conditions the control module commands the engine OFF.
Conditions for Clearing the MIL/DTC
DTCs P2120, P2122, P2123, P2125, P2127, P2128, and P2138 are Type A DTCs.
Diagnostic Aids
A high resistance condition on the accelerator pedal sensor circuits could cause a DTC to set.
Reference Information
Schematic Reference
Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Throttle Actuator Control (TAC) System Description (See: Powertrain Management/Computers and Control Systems/Description and
Operation/Throttle Actuator Control (TAC) System Description)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Showing posts with label P2122. Show all posts
Showing posts with label P2122. Show all posts
Tuesday, December 1, 2020
Monday, November 30, 2020
2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2489
2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2489
P2122
The ECM detects that the APP sensor 1 voltage is less than 0.46 V for greater than 0.2 s.
P2123
The ECM detects that the APP sensor 1 voltage is greater than 4.75 V for greater than 0.2 s.
P2125
The APP sensor 2 voltage is less than 0.32 V or greater than 2.6 V for greater than 0.2 s.
P2127
The ECM detects that the APP sensor 2 voltage is less than 0.32 V for greater than 0.2 s.
P2128
The ECM detects that the APP sensor 2 voltage is greater than 2.6 V for greater than 0.2 s.
P2138
The voltage difference between APP sensor 1 and APP sensor 2 exceeds a predetermined value for greater than 1 s.
Action Taken When the DTC Sets
* DTCs P2120, P2122, P2123, P2125, P2127, P2128, and P2138 are Type A DTCs.
* The control module commands the TAC system to operate in the Reduced Engine Power mode.
* A message center or an indicator displays Reduced Engine Power.
* Under certain conditions the control module commands the engine OFF.
Conditions for Clearing the MIL/DTC
DTCs P2120, P2122, P2123, P2125, P2127, P2128, and P2138 are Type A DTCs.
Diagnostic Aids
A high resistance condition on the accelerator pedal sensor circuits could cause a DTC to set.
Reference Information
Schematic Reference
Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Throttle Actuator Control (TAC) System Description (See: Powertrain Management/Computers and Control Systems/Description and
Operation/Throttle Actuator Control (TAC) System Description)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
P2122
The ECM detects that the APP sensor 1 voltage is less than 0.46 V for greater than 0.2 s.
P2123
The ECM detects that the APP sensor 1 voltage is greater than 4.75 V for greater than 0.2 s.
P2125
The APP sensor 2 voltage is less than 0.32 V or greater than 2.6 V for greater than 0.2 s.
P2127
The ECM detects that the APP sensor 2 voltage is less than 0.32 V for greater than 0.2 s.
P2128
The ECM detects that the APP sensor 2 voltage is greater than 2.6 V for greater than 0.2 s.
P2138
The voltage difference between APP sensor 1 and APP sensor 2 exceeds a predetermined value for greater than 1 s.
Action Taken When the DTC Sets
* DTCs P2120, P2122, P2123, P2125, P2127, P2128, and P2138 are Type A DTCs.
* The control module commands the TAC system to operate in the Reduced Engine Power mode.
* A message center or an indicator displays Reduced Engine Power.
* Under certain conditions the control module commands the engine OFF.
Conditions for Clearing the MIL/DTC
DTCs P2120, P2122, P2123, P2125, P2127, P2128, and P2138 are Type A DTCs.
Diagnostic Aids
A high resistance condition on the accelerator pedal sensor circuits could cause a DTC to set.
Reference Information
Schematic Reference
Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Throttle Actuator Control (TAC) System Description (See: Powertrain Management/Computers and Control Systems/Description and
Operation/Throttle Actuator Control (TAC) System Description)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2482
2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2482
P2122
The ECM detects that the APP sensor 1 voltage is less than 0.46 V for greater than 0.2 s.
P2123
The ECM detects that the APP sensor 1 voltage is greater than 4.75 V for greater than 0.2 s.
P2125
The APP sensor 2 voltage is less than 0.32 V or greater than 2.6 V for greater than 0.2 s.
P2127
The ECM detects that the APP sensor 2 voltage is less than 0.32 V for greater than 0.2 s.
P2128
The ECM detects that the APP sensor 2 voltage is greater than 2.6 V for greater than 0.2 s.
P2138
The voltage difference between APP sensor 1 and APP sensor 2 exceeds a predetermined value for greater than 1 s.
Action Taken When the DTC Sets
* DTCs P2120, P2122, P2123, P2125, P2127, P2128, and P2138 are Type A DTCs.
* The control module commands the TAC system to operate in the Reduced Engine Power mode.
* A message center or an indicator displays Reduced Engine Power.
* Under certain conditions the control module commands the engine OFF.
Conditions for Clearing the MIL/DTC
DTCs P2120, P2122, P2123, P2125, P2127, P2128, and P2138 are Type A DTCs.
Diagnostic Aids
A high resistance condition on the accelerator pedal sensor circuits could cause a DTC to set.
Reference Information
Schematic Reference
Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Throttle Actuator Control (TAC) System Description (See: Powertrain Management/Computers and Control Systems/Description and
Operation/Throttle Actuator Control (TAC) System Description)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
P2122
The ECM detects that the APP sensor 1 voltage is less than 0.46 V for greater than 0.2 s.
P2123
The ECM detects that the APP sensor 1 voltage is greater than 4.75 V for greater than 0.2 s.
P2125
The APP sensor 2 voltage is less than 0.32 V or greater than 2.6 V for greater than 0.2 s.
P2127
The ECM detects that the APP sensor 2 voltage is less than 0.32 V for greater than 0.2 s.
P2128
The ECM detects that the APP sensor 2 voltage is greater than 2.6 V for greater than 0.2 s.
P2138
The voltage difference between APP sensor 1 and APP sensor 2 exceeds a predetermined value for greater than 1 s.
Action Taken When the DTC Sets
* DTCs P2120, P2122, P2123, P2125, P2127, P2128, and P2138 are Type A DTCs.
* The control module commands the TAC system to operate in the Reduced Engine Power mode.
* A message center or an indicator displays Reduced Engine Power.
* Under certain conditions the control module commands the engine OFF.
Conditions for Clearing the MIL/DTC
DTCs P2120, P2122, P2123, P2125, P2127, P2128, and P2138 are Type A DTCs.
Diagnostic Aids
A high resistance condition on the accelerator pedal sensor circuits could cause a DTC to set.
Reference Information
Schematic Reference
Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Throttle Actuator Control (TAC) System Description (See: Powertrain Management/Computers and Control Systems/Description and
Operation/Throttle Actuator Control (TAC) System Description)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Tuesday, November 10, 2020
2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1999
2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1999
P0220, P0222, P0223, P0335, P0336, P0606, P0641, P0651, P1516, P2101, P2120, P2122, P2123, P2125, P2127, P2128, P2135, P2138, and
P2176 are not set.
* When DTC P0315 is set, the engine speed must be more than 1,000 RPM.
* Engine run time is more than 2 crankshaft revolutions.
* The engine speed is between 375-5,600 RPM.
* The ignition voltage is between 9-18 volts.
* The engine coolant temperature (ECT) is between -7 and +130掳C (+19 and +266掳F).
* When the startup ECT is colder than -7掳C (+19掳F), this diagnostic will be delayed until the ECT is warmer than +21掳C (+69掳F).
* The fuel level is more than 10 percent.
* The ECM is not in fuel shut-off, or decel fuel cut-off mode.
* The electronic brake control module (EBCM) and the traction control system (TCS) are not active or detecting rough road.
* An automatic transmission shift with a throttle position more than 95 percent is not occuring.
* The power management is not active.
* Excessive drive wheel slip is not detected.
* The power take-off (PTO) is disabled, where applicable.
* The cylinder deactivation is not in progress, where applicable.
* DTCs P0300-P0308 run continuously when the above conditions are met.
Conditions for Setting the DTC
DTC P0300
The ECM is detecting a crankshaft speed change indicating a random misfire is occuring that exceeds mandated emission level standards or is at
catalytic converter damaging levels.
DTC P0301, P0302, P0303, P0304, P0305, P0306, P0307, or P0308
The ECM is detecting a crankshaft speed change indicating a single cylinder misfire is occuring that exceeds mandated emission level standards or
is at catalytic converter damaging levels.
Action Taken When the DTC Sets
* DTCs P0300-P0308 are Type B DTCs.
* When the MIL is flashing the fuel injector may be disabled for the misfiring cylinder to protect the catalytic converter.
* Depending on the conditions that set the DTC, the engine may go into Open Loop.
Conditions for Clearing the MIL/DTC
* DTCs P0300-P0308 are Type B DTCs.
* The DTC must run and pass under the same operating conditions that were present when the DTC failed.
Diagnostic Aids
* Ensure that each fuel injector is connected to the proper fuel injector harness connector.
* A misfire may only occur when the engine is operating under a load or when the engine is cold.
* A high resistance condition on any ignition control (IC) circuit can cause an engine misfire P0300-P0308 DTC to set without setting an IC
circuit P0351-P0358 DTC.
* This test procedure requires that the vehicle battery has passed a load test and is completely charged. Refer to Battery Inspection/Test (See:
Starting and Charging/Testing and Inspection/Component Tests and General Diagnostics/Battery Inspection/Test).
* A misfire DTC could be caused by an excessive vibration from sources other than the engine. Inspect the following for possible sources of
vibration:
- A tire or wheel that is out of round or balance
- Variable thickness brake rotors
- An unbalanced drive shaft
- Certain rough road conditions
- A damaged accessory drive component or belt
- A damaged reluctor wheel
- The Crankshaft Position System Variation Learn procedure may need to be performed.
Reference Information
Schematic Reference
Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
P0220, P0222, P0223, P0335, P0336, P0606, P0641, P0651, P1516, P2101, P2120, P2122, P2123, P2125, P2127, P2128, P2135, P2138, and
P2176 are not set.
* When DTC P0315 is set, the engine speed must be more than 1,000 RPM.
* Engine run time is more than 2 crankshaft revolutions.
* The engine speed is between 375-5,600 RPM.
* The ignition voltage is between 9-18 volts.
* The engine coolant temperature (ECT) is between -7 and +130掳C (+19 and +266掳F).
* When the startup ECT is colder than -7掳C (+19掳F), this diagnostic will be delayed until the ECT is warmer than +21掳C (+69掳F).
* The fuel level is more than 10 percent.
* The ECM is not in fuel shut-off, or decel fuel cut-off mode.
* The electronic brake control module (EBCM) and the traction control system (TCS) are not active or detecting rough road.
* An automatic transmission shift with a throttle position more than 95 percent is not occuring.
* The power management is not active.
* Excessive drive wheel slip is not detected.
* The power take-off (PTO) is disabled, where applicable.
* The cylinder deactivation is not in progress, where applicable.
* DTCs P0300-P0308 run continuously when the above conditions are met.
Conditions for Setting the DTC
DTC P0300
The ECM is detecting a crankshaft speed change indicating a random misfire is occuring that exceeds mandated emission level standards or is at
catalytic converter damaging levels.
DTC P0301, P0302, P0303, P0304, P0305, P0306, P0307, or P0308
The ECM is detecting a crankshaft speed change indicating a single cylinder misfire is occuring that exceeds mandated emission level standards or
is at catalytic converter damaging levels.
Action Taken When the DTC Sets
* DTCs P0300-P0308 are Type B DTCs.
* When the MIL is flashing the fuel injector may be disabled for the misfiring cylinder to protect the catalytic converter.
* Depending on the conditions that set the DTC, the engine may go into Open Loop.
Conditions for Clearing the MIL/DTC
* DTCs P0300-P0308 are Type B DTCs.
* The DTC must run and pass under the same operating conditions that were present when the DTC failed.
Diagnostic Aids
* Ensure that each fuel injector is connected to the proper fuel injector harness connector.
* A misfire may only occur when the engine is operating under a load or when the engine is cold.
* A high resistance condition on any ignition control (IC) circuit can cause an engine misfire P0300-P0308 DTC to set without setting an IC
circuit P0351-P0358 DTC.
* This test procedure requires that the vehicle battery has passed a load test and is completely charged. Refer to Battery Inspection/Test (See:
Starting and Charging/Testing and Inspection/Component Tests and General Diagnostics/Battery Inspection/Test).
* A misfire DTC could be caused by an excessive vibration from sources other than the engine. Inspect the following for possible sources of
vibration:
- A tire or wheel that is out of round or balance
- Variable thickness brake rotors
- An unbalanced drive shaft
- Certain rough road conditions
- A damaged accessory drive component or belt
- A damaged reluctor wheel
- The Crankshaft Position System Variation Learn procedure may need to be performed.
Reference Information
Schematic Reference
Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Tuesday, June 30, 2020
2010 Cadillac Truck Escalade RWD V8-6.2L Page 1999
2010 Cadillac Truck Escalade RWD V8-6.2L Page 1999
P0220, P0222, P0223, P0335, P0336, P0606, P0641, P0651, P1516, P2101, P2120, P2122, P2123, P2125, P2127, P2128, P2135, P2138, and
P2176 are not set.
* When DTC P0315 is set, the engine speed must be more than 1,000 RPM.
* Engine run time is more than 2 crankshaft revolutions.
* The engine speed is between 375-5,600 RPM.
* The ignition voltage is between 9-18 volts.
* The engine coolant temperature (ECT) is between -7 and +130掳C (+19 and +266掳F).
* When the startup ECT is colder than -7掳C (+19掳F), this diagnostic will be delayed until the ECT is warmer than +21掳C (+69掳F).
* The fuel level is more than 10 percent.
* The ECM is not in fuel shut-off, or decel fuel cut-off mode.
* The electronic brake control module (EBCM) and the traction control system (TCS) are not active or detecting rough road.
* An automatic transmission shift with a throttle position more than 95 percent is not occuring.
* The power management is not active.
* Excessive drive wheel slip is not detected.
* The power take-off (PTO) is disabled, where applicable.
* The cylinder deactivation is not in progress, where applicable.
* DTCs P0300-P0308 run continuously when the above conditions are met.
Conditions for Setting the DTC
DTC P0300
The ECM is detecting a crankshaft speed change indicating a random misfire is occuring that exceeds mandated emission level standards or is at
catalytic converter damaging levels.
DTC P0301, P0302, P0303, P0304, P0305, P0306, P0307, or P0308
The ECM is detecting a crankshaft speed change indicating a single cylinder misfire is occuring that exceeds mandated emission level standards or
is at catalytic converter damaging levels.
Action Taken When the DTC Sets
* DTCs P0300-P0308 are Type B DTCs.
* When the MIL is flashing the fuel injector may be disabled for the misfiring cylinder to protect the catalytic converter.
* Depending on the conditions that set the DTC, the engine may go into Open Loop.
Conditions for Clearing the MIL/DTC
* DTCs P0300-P0308 are Type B DTCs.
* The DTC must run and pass under the same operating conditions that were present when the DTC failed.
Diagnostic Aids
* Ensure that each fuel injector is connected to the proper fuel injector harness connector.
* A misfire may only occur when the engine is operating under a load or when the engine is cold.
* A high resistance condition on any ignition control (IC) circuit can cause an engine misfire P0300-P0308 DTC to set without setting an IC
circuit P0351-P0358 DTC.
* This test procedure requires that the vehicle battery has passed a load test and is completely charged. Refer to Battery Inspection/Test (See:
Starting and Charging/Testing and Inspection/Component Tests and General Diagnostics/Battery Inspection/Test).
* A misfire DTC could be caused by an excessive vibration from sources other than the engine. Inspect the following for possible sources of
vibration:
- A tire or wheel that is out of round or balance
- Variable thickness brake rotors
- An unbalanced drive shaft
- Certain rough road conditions
- A damaged accessory drive component or belt
- A damaged reluctor wheel
- The Crankshaft Position System Variation Learn procedure may need to be performed.
Reference Information
Schematic Reference
Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
P0220, P0222, P0223, P0335, P0336, P0606, P0641, P0651, P1516, P2101, P2120, P2122, P2123, P2125, P2127, P2128, P2135, P2138, and
P2176 are not set.
* When DTC P0315 is set, the engine speed must be more than 1,000 RPM.
* Engine run time is more than 2 crankshaft revolutions.
* The engine speed is between 375-5,600 RPM.
* The ignition voltage is between 9-18 volts.
* The engine coolant temperature (ECT) is between -7 and +130掳C (+19 and +266掳F).
* When the startup ECT is colder than -7掳C (+19掳F), this diagnostic will be delayed until the ECT is warmer than +21掳C (+69掳F).
* The fuel level is more than 10 percent.
* The ECM is not in fuel shut-off, or decel fuel cut-off mode.
* The electronic brake control module (EBCM) and the traction control system (TCS) are not active or detecting rough road.
* An automatic transmission shift with a throttle position more than 95 percent is not occuring.
* The power management is not active.
* Excessive drive wheel slip is not detected.
* The power take-off (PTO) is disabled, where applicable.
* The cylinder deactivation is not in progress, where applicable.
* DTCs P0300-P0308 run continuously when the above conditions are met.
Conditions for Setting the DTC
DTC P0300
The ECM is detecting a crankshaft speed change indicating a random misfire is occuring that exceeds mandated emission level standards or is at
catalytic converter damaging levels.
DTC P0301, P0302, P0303, P0304, P0305, P0306, P0307, or P0308
The ECM is detecting a crankshaft speed change indicating a single cylinder misfire is occuring that exceeds mandated emission level standards or
is at catalytic converter damaging levels.
Action Taken When the DTC Sets
* DTCs P0300-P0308 are Type B DTCs.
* When the MIL is flashing the fuel injector may be disabled for the misfiring cylinder to protect the catalytic converter.
* Depending on the conditions that set the DTC, the engine may go into Open Loop.
Conditions for Clearing the MIL/DTC
* DTCs P0300-P0308 are Type B DTCs.
* The DTC must run and pass under the same operating conditions that were present when the DTC failed.
Diagnostic Aids
* Ensure that each fuel injector is connected to the proper fuel injector harness connector.
* A misfire may only occur when the engine is operating under a load or when the engine is cold.
* A high resistance condition on any ignition control (IC) circuit can cause an engine misfire P0300-P0308 DTC to set without setting an IC
circuit P0351-P0358 DTC.
* This test procedure requires that the vehicle battery has passed a load test and is completely charged. Refer to Battery Inspection/Test (See:
Starting and Charging/Testing and Inspection/Component Tests and General Diagnostics/Battery Inspection/Test).
* A misfire DTC could be caused by an excessive vibration from sources other than the engine. Inspect the following for possible sources of
vibration:
- A tire or wheel that is out of round or balance
- Variable thickness brake rotors
- An unbalanced drive shaft
- Certain rough road conditions
- A damaged accessory drive component or belt
- A damaged reluctor wheel
- The Crankshaft Position System Variation Learn procedure may need to be performed.
Reference Information
Schematic Reference
Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Monday, December 23, 2019
2010 Cadillac Truck Escalade AWD V8-6.2L Page 2601
P2122
The ECM detects that the APP sensor 1 voltage is less than 0.46 V for greater than 0.2 s.
P2123
The ECM detects that the APP sensor 1 voltage is greater than 4.75 V for greater than 0.2 s.
P2125
The APP sensor 2 voltage is less than 0.32 V or greater than 2.6 V for greater than 0.2 s.
P2127
The ECM detects that the APP sensor 2 voltage is less than 0.32 V for greater than 0.2 s.
P2128
The ECM detects that the APP sensor 2 voltage is greater than 2.6 V for greater than 0.2 s.
P2138
The voltage difference between APP sensor 1 and APP sensor 2 exceeds a predetermined value for greater than 1 s.
Action Taken When the DTC Sets
* DTCs P2120, P2122, P2123, P2125, P2127, P2128, and P2138 are Type A DTCs.
* The control module commands the TAC system to operate in the Reduced Engine Power mode.
* A message center or an indicator displays Reduced Engine Power.
* Under certain conditions the control module commands the engine OFF.
Conditions for Clearing the MIL/DTC
DTCs P2120, P2122, P2123, P2125, P2127, P2128, and P2138 are Type A DTCs.
Diagnostic Aids
A high resistance condition on the accelerator pedal sensor circuits could cause a DTC to set.
Reference Information
Schematic Reference
Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Throttle Actuator Control (TAC) System Description (See: Powertrain Management/Computers and Control Systems/Description and
Operation/Throttle Actuator Control (TAC) System Description)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
The ECM detects that the APP sensor 1 voltage is less than 0.46 V for greater than 0.2 s.
P2123
The ECM detects that the APP sensor 1 voltage is greater than 4.75 V for greater than 0.2 s.
P2125
The APP sensor 2 voltage is less than 0.32 V or greater than 2.6 V for greater than 0.2 s.
P2127
The ECM detects that the APP sensor 2 voltage is less than 0.32 V for greater than 0.2 s.
P2128
The ECM detects that the APP sensor 2 voltage is greater than 2.6 V for greater than 0.2 s.
P2138
The voltage difference between APP sensor 1 and APP sensor 2 exceeds a predetermined value for greater than 1 s.
Action Taken When the DTC Sets
* DTCs P2120, P2122, P2123, P2125, P2127, P2128, and P2138 are Type A DTCs.
* The control module commands the TAC system to operate in the Reduced Engine Power mode.
* A message center or an indicator displays Reduced Engine Power.
* Under certain conditions the control module commands the engine OFF.
Conditions for Clearing the MIL/DTC
DTCs P2120, P2122, P2123, P2125, P2127, P2128, and P2138 are Type A DTCs.
Diagnostic Aids
A high resistance condition on the accelerator pedal sensor circuits could cause a DTC to set.
Reference Information
Schematic Reference
Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Throttle Actuator Control (TAC) System Description (See: Powertrain Management/Computers and Control Systems/Description and
Operation/Throttle Actuator Control (TAC) System Description)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
2010 Cadillac Truck Escalade AWD V8-6.2L Page 2594
P2122
The ECM detects that the APP sensor 1 voltage is less than 0.46 V for greater than 0.2 s.
P2123
The ECM detects that the APP sensor 1 voltage is greater than 4.75 V for greater than 0.2 s.
P2125
The APP sensor 2 voltage is less than 0.32 V or greater than 2.6 V for greater than 0.2 s.
P2127
The ECM detects that the APP sensor 2 voltage is less than 0.32 V for greater than 0.2 s.
P2128
The ECM detects that the APP sensor 2 voltage is greater than 2.6 V for greater than 0.2 s.
P2138
The voltage difference between APP sensor 1 and APP sensor 2 exceeds a predetermined value for greater than 1 s.
Action Taken When the DTC Sets
* DTCs P2120, P2122, P2123, P2125, P2127, P2128, and P2138 are Type A DTCs.
* The control module commands the TAC system to operate in the Reduced Engine Power mode.
* A message center or an indicator displays Reduced Engine Power.
* Under certain conditions the control module commands the engine OFF.
Conditions for Clearing the MIL/DTC
DTCs P2120, P2122, P2123, P2125, P2127, P2128, and P2138 are Type A DTCs.
Diagnostic Aids
A high resistance condition on the accelerator pedal sensor circuits could cause a DTC to set.
Reference Information
Schematic Reference
Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Throttle Actuator Control (TAC) System Description (See: Powertrain Management/Computers and Control Systems/Description and
Operation/Throttle Actuator Control (TAC) System Description)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
The ECM detects that the APP sensor 1 voltage is less than 0.46 V for greater than 0.2 s.
P2123
The ECM detects that the APP sensor 1 voltage is greater than 4.75 V for greater than 0.2 s.
P2125
The APP sensor 2 voltage is less than 0.32 V or greater than 2.6 V for greater than 0.2 s.
P2127
The ECM detects that the APP sensor 2 voltage is less than 0.32 V for greater than 0.2 s.
P2128
The ECM detects that the APP sensor 2 voltage is greater than 2.6 V for greater than 0.2 s.
P2138
The voltage difference between APP sensor 1 and APP sensor 2 exceeds a predetermined value for greater than 1 s.
Action Taken When the DTC Sets
* DTCs P2120, P2122, P2123, P2125, P2127, P2128, and P2138 are Type A DTCs.
* The control module commands the TAC system to operate in the Reduced Engine Power mode.
* A message center or an indicator displays Reduced Engine Power.
* Under certain conditions the control module commands the engine OFF.
Conditions for Clearing the MIL/DTC
DTCs P2120, P2122, P2123, P2125, P2127, P2128, and P2138 are Type A DTCs.
Diagnostic Aids
A high resistance condition on the accelerator pedal sensor circuits could cause a DTC to set.
Reference Information
Schematic Reference
Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Throttle Actuator Control (TAC) System Description (See: Powertrain Management/Computers and Control Systems/Description and
Operation/Throttle Actuator Control (TAC) System Description)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
2010 Cadillac Truck Escalade AWD V8-6.2L Page 2587
P2122
The ECM detects that the APP sensor 1 voltage is less than 0.46 V for greater than 0.2 s.
P2123
The ECM detects that the APP sensor 1 voltage is greater than 4.75 V for greater than 0.2 s.
P2125
The APP sensor 2 voltage is less than 0.32 V or greater than 2.6 V for greater than 0.2 s.
P2127
The ECM detects that the APP sensor 2 voltage is less than 0.32 V for greater than 0.2 s.
P2128
The ECM detects that the APP sensor 2 voltage is greater than 2.6 V for greater than 0.2 s.
P2138
The voltage difference between APP sensor 1 and APP sensor 2 exceeds a predetermined value for greater than 1 s.
Action Taken When the DTC Sets
* DTCs P2120, P2122, P2123, P2125, P2127, P2128, and P2138 are Type A DTCs.
* The control module commands the TAC system to operate in the Reduced Engine Power mode.
* A message center or an indicator displays Reduced Engine Power.
* Under certain conditions the control module commands the engine OFF.
Conditions for Clearing the MIL/DTC
DTCs P2120, P2122, P2123, P2125, P2127, P2128, and P2138 are Type A DTCs.
Diagnostic Aids
A high resistance condition on the accelerator pedal sensor circuits could cause a DTC to set.
Reference Information
Schematic Reference
Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Throttle Actuator Control (TAC) System Description (See: Powertrain Management/Computers and Control Systems/Description and
Operation/Throttle Actuator Control (TAC) System Description)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
The ECM detects that the APP sensor 1 voltage is less than 0.46 V for greater than 0.2 s.
P2123
The ECM detects that the APP sensor 1 voltage is greater than 4.75 V for greater than 0.2 s.
P2125
The APP sensor 2 voltage is less than 0.32 V or greater than 2.6 V for greater than 0.2 s.
P2127
The ECM detects that the APP sensor 2 voltage is less than 0.32 V for greater than 0.2 s.
P2128
The ECM detects that the APP sensor 2 voltage is greater than 2.6 V for greater than 0.2 s.
P2138
The voltage difference between APP sensor 1 and APP sensor 2 exceeds a predetermined value for greater than 1 s.
Action Taken When the DTC Sets
* DTCs P2120, P2122, P2123, P2125, P2127, P2128, and P2138 are Type A DTCs.
* The control module commands the TAC system to operate in the Reduced Engine Power mode.
* A message center or an indicator displays Reduced Engine Power.
* Under certain conditions the control module commands the engine OFF.
Conditions for Clearing the MIL/DTC
DTCs P2120, P2122, P2123, P2125, P2127, P2128, and P2138 are Type A DTCs.
Diagnostic Aids
A high resistance condition on the accelerator pedal sensor circuits could cause a DTC to set.
Reference Information
Schematic Reference
Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Throttle Actuator Control (TAC) System Description (See: Powertrain Management/Computers and Control Systems/Description and
Operation/Throttle Actuator Control (TAC) System Description)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Tuesday, December 17, 2019
2010 Cadillac Truck Escalade AWD V8-6.2L Page 2087
P0220, P0222, P0223, P0335, P0336, P0606, P0641, P0651, P1516, P2101, P2120, P2122, P2123, P2125, P2127, P2128, P2135, P2138, and
P2176 are not set.
* When DTC P0315 is set, the engine speed must be more than 1,000 RPM.
* Engine run time is more than 2 crankshaft revolutions.
* The engine speed is between 375-5,600 RPM.
* The ignition voltage is between 9-18 volts.
* The engine coolant temperature (ECT) is between -7 and +130锟斤拷C (+19 and +266锟斤拷F).
* When the startup ECT is colder than -7锟斤拷C (+19锟斤拷F), this diagnostic will be delayed until the ECT is warmer than +21锟斤拷C (+69锟斤拷F).
* The fuel level is more than 10 percent.
* The ECM is not in fuel shut-off, or decel fuel cut-off mode.
* The electronic brake control module (EBCM) and the traction control system (TCS) are not active or detecting rough road.
* An automatic transmission shift with a throttle position more than 95 percent is not occuring.
* The power management is not active.
* Excessive drive wheel slip is not detected.
* The power take-off (PTO) is disabled, where applicable.
* The cylinder deactivation is not in progress, where applicable.
* DTCs P0300-P0308 run continuously when the above conditions are met.
Conditions for Setting the DTC
DTC P0300
The ECM is detecting a crankshaft speed change indicating a random misfire is occuring that exceeds mandated emission level standards or is at
catalytic converter damaging levels.
DTC P0301, P0302, P0303, P0304, P0305, P0306, P0307, or P0308
The ECM is detecting a crankshaft speed change indicating a single cylinder misfire is occuring that exceeds mandated emission level standards or
is at catalytic converter damaging levels.
Action Taken When the DTC Sets
* DTCs P0300-P0308 are Type B DTCs.
* When the MIL is flashing the fuel injector may be disabled for the misfiring cylinder to protect the catalytic converter.
* Depending on the conditions that set the DTC, the engine may go into Open Loop.
Conditions for Clearing the MIL/DTC
* DTCs P0300-P0308 are Type B DTCs.
* The DTC must run and pass under the same operating conditions that were present when the DTC failed.
Diagnostic Aids
* Ensure that each fuel injector is connected to the proper fuel injector harness connector.
* A misfire may only occur when the engine is operating under a load or when the engine is cold.
* A high resistance condition on any ignition control (IC) circuit can cause an engine misfire P0300-P0308 DTC to set without setting an IC
circuit P0351-P0358 DTC.
* This test procedure requires that the vehicle battery has passed a load test and is completely charged. Refer to Battery Inspection/Test (See:
Starting and Charging/Testing and Inspection/Component Tests and General Diagnostics/Battery Inspection/Test).
* A misfire DTC could be caused by an excessive vibration from sources other than the engine. Inspect the following for possible sources of
vibration:
- A tire or wheel that is out of round or balance
- Variable thickness brake rotors
- An unbalanced drive shaft
- Certain rough road conditions
- A damaged accessory drive component or belt
- A damaged reluctor wheel
- The Crankshaft Position System Variation Learn procedure may need to be performed.
Reference Information
Schematic Reference
Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
P2176 are not set.
* When DTC P0315 is set, the engine speed must be more than 1,000 RPM.
* Engine run time is more than 2 crankshaft revolutions.
* The engine speed is between 375-5,600 RPM.
* The ignition voltage is between 9-18 volts.
* The engine coolant temperature (ECT) is between -7 and +130锟斤拷C (+19 and +266锟斤拷F).
* When the startup ECT is colder than -7锟斤拷C (+19锟斤拷F), this diagnostic will be delayed until the ECT is warmer than +21锟斤拷C (+69锟斤拷F).
* The fuel level is more than 10 percent.
* The ECM is not in fuel shut-off, or decel fuel cut-off mode.
* The electronic brake control module (EBCM) and the traction control system (TCS) are not active or detecting rough road.
* An automatic transmission shift with a throttle position more than 95 percent is not occuring.
* The power management is not active.
* Excessive drive wheel slip is not detected.
* The power take-off (PTO) is disabled, where applicable.
* The cylinder deactivation is not in progress, where applicable.
* DTCs P0300-P0308 run continuously when the above conditions are met.
Conditions for Setting the DTC
DTC P0300
The ECM is detecting a crankshaft speed change indicating a random misfire is occuring that exceeds mandated emission level standards or is at
catalytic converter damaging levels.
DTC P0301, P0302, P0303, P0304, P0305, P0306, P0307, or P0308
The ECM is detecting a crankshaft speed change indicating a single cylinder misfire is occuring that exceeds mandated emission level standards or
is at catalytic converter damaging levels.
Action Taken When the DTC Sets
* DTCs P0300-P0308 are Type B DTCs.
* When the MIL is flashing the fuel injector may be disabled for the misfiring cylinder to protect the catalytic converter.
* Depending on the conditions that set the DTC, the engine may go into Open Loop.
Conditions for Clearing the MIL/DTC
* DTCs P0300-P0308 are Type B DTCs.
* The DTC must run and pass under the same operating conditions that were present when the DTC failed.
Diagnostic Aids
* Ensure that each fuel injector is connected to the proper fuel injector harness connector.
* A misfire may only occur when the engine is operating under a load or when the engine is cold.
* A high resistance condition on any ignition control (IC) circuit can cause an engine misfire P0300-P0308 DTC to set without setting an IC
circuit P0351-P0358 DTC.
* This test procedure requires that the vehicle battery has passed a load test and is completely charged. Refer to Battery Inspection/Test (See:
Starting and Charging/Testing and Inspection/Component Tests and General Diagnostics/Battery Inspection/Test).
* A misfire DTC could be caused by an excessive vibration from sources other than the engine. Inspect the following for possible sources of
vibration:
- A tire or wheel that is out of round or balance
- Variable thickness brake rotors
- An unbalanced drive shaft
- Certain rough road conditions
- A damaged accessory drive component or belt
- A damaged reluctor wheel
- The Crankshaft Position System Variation Learn procedure may need to be performed.
Reference Information
Schematic Reference
Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Subscribe to:
Posts (Atom)