2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1999
P0220, P0222, P0223, P0335, P0336, P0606, P0641, P0651, P1516, P2101, P2120, P2122, P2123, P2125, P2127, P2128, P2135, P2138, and
P2176 are not set.
* When DTC P0315 is set, the engine speed must be more than 1,000 RPM.
* Engine run time is more than 2 crankshaft revolutions.
* The engine speed is between 375-5,600 RPM.
* The ignition voltage is between 9-18 volts.
* The engine coolant temperature (ECT) is between -7 and +130掳C (+19 and +266掳F).
* When the startup ECT is colder than -7掳C (+19掳F), this diagnostic will be delayed until the ECT is warmer than +21掳C (+69掳F).
* The fuel level is more than 10 percent.
* The ECM is not in fuel shut-off, or decel fuel cut-off mode.
* The electronic brake control module (EBCM) and the traction control system (TCS) are not active or detecting rough road.
* An automatic transmission shift with a throttle position more than 95 percent is not occuring.
* The power management is not active.
* Excessive drive wheel slip is not detected.
* The power take-off (PTO) is disabled, where applicable.
* The cylinder deactivation is not in progress, where applicable.
* DTCs P0300-P0308 run continuously when the above conditions are met.
Conditions for Setting the DTC
DTC P0300
The ECM is detecting a crankshaft speed change indicating a random misfire is occuring that exceeds mandated emission level standards or is at
catalytic converter damaging levels.
DTC P0301, P0302, P0303, P0304, P0305, P0306, P0307, or P0308
The ECM is detecting a crankshaft speed change indicating a single cylinder misfire is occuring that exceeds mandated emission level standards or
is at catalytic converter damaging levels.
Action Taken When the DTC Sets
* DTCs P0300-P0308 are Type B DTCs.
* When the MIL is flashing the fuel injector may be disabled for the misfiring cylinder to protect the catalytic converter.
* Depending on the conditions that set the DTC, the engine may go into Open Loop.
Conditions for Clearing the MIL/DTC
* DTCs P0300-P0308 are Type B DTCs.
* The DTC must run and pass under the same operating conditions that were present when the DTC failed.
Diagnostic Aids
* Ensure that each fuel injector is connected to the proper fuel injector harness connector.
* A misfire may only occur when the engine is operating under a load or when the engine is cold.
* A high resistance condition on any ignition control (IC) circuit can cause an engine misfire P0300-P0308 DTC to set without setting an IC
circuit P0351-P0358 DTC.
* This test procedure requires that the vehicle battery has passed a load test and is completely charged. Refer to Battery Inspection/Test (See:
Starting and Charging/Testing and Inspection/Component Tests and General Diagnostics/Battery Inspection/Test).
* A misfire DTC could be caused by an excessive vibration from sources other than the engine. Inspect the following for possible sources of
vibration:
- A tire or wheel that is out of round or balance
- Variable thickness brake rotors
- An unbalanced drive shaft
- Certain rough road conditions
- A damaged accessory drive component or belt
- A damaged reluctor wheel
- The Crankshaft Position System Variation Learn procedure may need to be performed.
Reference Information
Schematic Reference
Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Showing posts with label P0222. Show all posts
Showing posts with label P0222. Show all posts
Tuesday, November 10, 2020
Sunday, November 8, 2020
2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1950
2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1950
DTC P0120, P0122, P0123, P0220, P0222, P0223, or P2135
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC P0120
- Throttle Position (TP) Sensor 1 Circuit
DTC P0122
- Throttle Position (TP) Sensor 1 Circuit Low Voltage
DTC P0123
- Throttle Position (TP) Sensor 1 Circuit High Voltage
DTC P0220
- Throttle Position (TP) Sensor 2 Circuit
DTC P0222
- Throttle Position (TP) Sensor 2 Circuit Low Voltage
DTC P0223
- Throttle Position (TP) Sensor 2 Circuit High Voltage
DTC P2135
- Throttle Position (TP) Sensor 1-2 Correlation
Diagnostic Fault Information
Typical Scan Tool Data
DTC P0120, P0122, P0123, P0220, P0222, P0223, or P2135
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC P0120
- Throttle Position (TP) Sensor 1 Circuit
DTC P0122
- Throttle Position (TP) Sensor 1 Circuit Low Voltage
DTC P0123
- Throttle Position (TP) Sensor 1 Circuit High Voltage
DTC P0220
- Throttle Position (TP) Sensor 2 Circuit
DTC P0222
- Throttle Position (TP) Sensor 2 Circuit Low Voltage
DTC P0223
- Throttle Position (TP) Sensor 2 Circuit High Voltage
DTC P2135
- Throttle Position (TP) Sensor 1-2 Correlation
Diagnostic Fault Information
Typical Scan Tool Data
Wednesday, November 4, 2020
2010 Cadillac CTS Sedan AWD V6-3.0L Page 1843
2010 Cadillac CTS Sedan AWD V6-3.0L Page 1843
DTC P0121-P0123, P0222, P0223, or P2135 (LF1)
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC P0121
- Throttle Position Sensor Performance
DTC P0122
- Throttle Position Sensor 1 Circuit Low Voltage
DTC P0123
- Throttle Position Sensor 1 Circuit High Voltage
DTC P0222
- Throttle Position Sensor 2 Circuit Low Voltage
DTC P0223
- Throttle Position Sensor 2 Circuit High Voltage
DTC P2135
- Throttle Position Sensors 1-2 Not Plausible
Diagnostic Fault Information
Typical Scan Tool Data
Circuit/System Description
The throttle body assembly contains 2 throttle position (TP) sensors. The TP sensors are mounted to the throttle body assembly and are not
serviceable. The TP sensors provide a signal voltage that changes relative to throttle blade angle. The engine control module (ECM) supplies the TP
sensors with a common 5-volt reference circuit, a common low reference circuit, and 2 independent signal circuits.
Sunday, November 1, 2020
2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1792
2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1792
P0134, P0135, P0137, P0138, P013A, P013B, P013E, P013F, P0140, P0141, P0171, P0172, P0201, P0202, P0203, P0204, P0220, P0222,
P0223, P0300, P0442, P0443, P0446, P0449, P0455, P0496, P1133, P1174, P1516, P2101, P2119, P2135, P2176, P2270, P2271, P2A00 are
not set.
* The ignition 1 voltage is between 10-32 V.
* The learned heater resistance is valid.
* The fuel level is greater than 10 %.
* The engine run time is equal to or greater than 5 minutes.
* The DTCs run once per ignition cycle when the above conditions are met.
Conditions for Setting the DTC
P0133 or P0153
* The ECM detects that the HO2S 1 rich-to-lean or lean-to-rich average response time is greater than a calibrated value.
* The DTCs set within 100 s when the above condition is met.
P013A or P013C
The ECM detects that the accumulated mass air flow monitored during rich-to-lean transitions between 450-150 mV is greater than 75 grams.
P013B or P013D
The ECM detects that the accumulated mass air flow monitored during lean-to-rich transitions between 350-650 mV is greater than 75 grams.
P013E or P014A
The ECM detects that the O2 sensor voltage has not decreased below 450 mV within 42 grams of accumulated air flow.
P013F or P014B
The ECM detects that the O2 sensor voltage has not increased above 350 mV within 200 grams of accumulated air flow.
P1133 or P1153
* The ECM detects that the HO2S 1 rich-to-lean counts, or the lean-to-rich counts are less than a calibrated value.
* The DTCs set within 100 s when the above condition is met.
Action Taken When the DTC Sets
DTCs P0133, P013A, P013B, P013C, P013D, P013E, P013F, P014A, P014B, P0153, P1133, and P1153 are Type B DTCs.
Conditions for Clearing the DTC
DTCs P0133, P013A, P013B, P013C, P013D, P013E, P013F, P014A, P014B, P0153, P1133, and P1153 are Type B DTCs.
Reference Information
Schematic Reference
Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
* Heated Oxygen Sensor Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical
Diagnostic Procedures/Wiring Repairs/Heated Oxygen Sensor Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
P0134, P0135, P0137, P0138, P013A, P013B, P013E, P013F, P0140, P0141, P0171, P0172, P0201, P0202, P0203, P0204, P0220, P0222,
P0223, P0300, P0442, P0443, P0446, P0449, P0455, P0496, P1133, P1174, P1516, P2101, P2119, P2135, P2176, P2270, P2271, P2A00 are
not set.
* The ignition 1 voltage is between 10-32 V.
* The learned heater resistance is valid.
* The fuel level is greater than 10 %.
* The engine run time is equal to or greater than 5 minutes.
* The DTCs run once per ignition cycle when the above conditions are met.
Conditions for Setting the DTC
P0133 or P0153
* The ECM detects that the HO2S 1 rich-to-lean or lean-to-rich average response time is greater than a calibrated value.
* The DTCs set within 100 s when the above condition is met.
P013A or P013C
The ECM detects that the accumulated mass air flow monitored during rich-to-lean transitions between 450-150 mV is greater than 75 grams.
P013B or P013D
The ECM detects that the accumulated mass air flow monitored during lean-to-rich transitions between 350-650 mV is greater than 75 grams.
P013E or P014A
The ECM detects that the O2 sensor voltage has not decreased below 450 mV within 42 grams of accumulated air flow.
P013F or P014B
The ECM detects that the O2 sensor voltage has not increased above 350 mV within 200 grams of accumulated air flow.
P1133 or P1153
* The ECM detects that the HO2S 1 rich-to-lean counts, or the lean-to-rich counts are less than a calibrated value.
* The DTCs set within 100 s when the above condition is met.
Action Taken When the DTC Sets
DTCs P0133, P013A, P013B, P013C, P013D, P013E, P013F, P014A, P014B, P0153, P1133, and P1153 are Type B DTCs.
Conditions for Clearing the DTC
DTCs P0133, P013A, P013B, P013C, P013D, P013E, P013F, P014A, P014B, P0153, P1133, and P1153 are Type B DTCs.
Reference Information
Schematic Reference
Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
* Heated Oxygen Sensor Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical
Diagnostic Procedures/Wiring Repairs/Heated Oxygen Sensor Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Tuesday, June 30, 2020
2010 Cadillac Truck Escalade RWD V8-6.2L Page 1999
2010 Cadillac Truck Escalade RWD V8-6.2L Page 1999
P0220, P0222, P0223, P0335, P0336, P0606, P0641, P0651, P1516, P2101, P2120, P2122, P2123, P2125, P2127, P2128, P2135, P2138, and
P2176 are not set.
* When DTC P0315 is set, the engine speed must be more than 1,000 RPM.
* Engine run time is more than 2 crankshaft revolutions.
* The engine speed is between 375-5,600 RPM.
* The ignition voltage is between 9-18 volts.
* The engine coolant temperature (ECT) is between -7 and +130掳C (+19 and +266掳F).
* When the startup ECT is colder than -7掳C (+19掳F), this diagnostic will be delayed until the ECT is warmer than +21掳C (+69掳F).
* The fuel level is more than 10 percent.
* The ECM is not in fuel shut-off, or decel fuel cut-off mode.
* The electronic brake control module (EBCM) and the traction control system (TCS) are not active or detecting rough road.
* An automatic transmission shift with a throttle position more than 95 percent is not occuring.
* The power management is not active.
* Excessive drive wheel slip is not detected.
* The power take-off (PTO) is disabled, where applicable.
* The cylinder deactivation is not in progress, where applicable.
* DTCs P0300-P0308 run continuously when the above conditions are met.
Conditions for Setting the DTC
DTC P0300
The ECM is detecting a crankshaft speed change indicating a random misfire is occuring that exceeds mandated emission level standards or is at
catalytic converter damaging levels.
DTC P0301, P0302, P0303, P0304, P0305, P0306, P0307, or P0308
The ECM is detecting a crankshaft speed change indicating a single cylinder misfire is occuring that exceeds mandated emission level standards or
is at catalytic converter damaging levels.
Action Taken When the DTC Sets
* DTCs P0300-P0308 are Type B DTCs.
* When the MIL is flashing the fuel injector may be disabled for the misfiring cylinder to protect the catalytic converter.
* Depending on the conditions that set the DTC, the engine may go into Open Loop.
Conditions for Clearing the MIL/DTC
* DTCs P0300-P0308 are Type B DTCs.
* The DTC must run and pass under the same operating conditions that were present when the DTC failed.
Diagnostic Aids
* Ensure that each fuel injector is connected to the proper fuel injector harness connector.
* A misfire may only occur when the engine is operating under a load or when the engine is cold.
* A high resistance condition on any ignition control (IC) circuit can cause an engine misfire P0300-P0308 DTC to set without setting an IC
circuit P0351-P0358 DTC.
* This test procedure requires that the vehicle battery has passed a load test and is completely charged. Refer to Battery Inspection/Test (See:
Starting and Charging/Testing and Inspection/Component Tests and General Diagnostics/Battery Inspection/Test).
* A misfire DTC could be caused by an excessive vibration from sources other than the engine. Inspect the following for possible sources of
vibration:
- A tire or wheel that is out of round or balance
- Variable thickness brake rotors
- An unbalanced drive shaft
- Certain rough road conditions
- A damaged accessory drive component or belt
- A damaged reluctor wheel
- The Crankshaft Position System Variation Learn procedure may need to be performed.
Reference Information
Schematic Reference
Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
P0220, P0222, P0223, P0335, P0336, P0606, P0641, P0651, P1516, P2101, P2120, P2122, P2123, P2125, P2127, P2128, P2135, P2138, and
P2176 are not set.
* When DTC P0315 is set, the engine speed must be more than 1,000 RPM.
* Engine run time is more than 2 crankshaft revolutions.
* The engine speed is between 375-5,600 RPM.
* The ignition voltage is between 9-18 volts.
* The engine coolant temperature (ECT) is between -7 and +130掳C (+19 and +266掳F).
* When the startup ECT is colder than -7掳C (+19掳F), this diagnostic will be delayed until the ECT is warmer than +21掳C (+69掳F).
* The fuel level is more than 10 percent.
* The ECM is not in fuel shut-off, or decel fuel cut-off mode.
* The electronic brake control module (EBCM) and the traction control system (TCS) are not active or detecting rough road.
* An automatic transmission shift with a throttle position more than 95 percent is not occuring.
* The power management is not active.
* Excessive drive wheel slip is not detected.
* The power take-off (PTO) is disabled, where applicable.
* The cylinder deactivation is not in progress, where applicable.
* DTCs P0300-P0308 run continuously when the above conditions are met.
Conditions for Setting the DTC
DTC P0300
The ECM is detecting a crankshaft speed change indicating a random misfire is occuring that exceeds mandated emission level standards or is at
catalytic converter damaging levels.
DTC P0301, P0302, P0303, P0304, P0305, P0306, P0307, or P0308
The ECM is detecting a crankshaft speed change indicating a single cylinder misfire is occuring that exceeds mandated emission level standards or
is at catalytic converter damaging levels.
Action Taken When the DTC Sets
* DTCs P0300-P0308 are Type B DTCs.
* When the MIL is flashing the fuel injector may be disabled for the misfiring cylinder to protect the catalytic converter.
* Depending on the conditions that set the DTC, the engine may go into Open Loop.
Conditions for Clearing the MIL/DTC
* DTCs P0300-P0308 are Type B DTCs.
* The DTC must run and pass under the same operating conditions that were present when the DTC failed.
Diagnostic Aids
* Ensure that each fuel injector is connected to the proper fuel injector harness connector.
* A misfire may only occur when the engine is operating under a load or when the engine is cold.
* A high resistance condition on any ignition control (IC) circuit can cause an engine misfire P0300-P0308 DTC to set without setting an IC
circuit P0351-P0358 DTC.
* This test procedure requires that the vehicle battery has passed a load test and is completely charged. Refer to Battery Inspection/Test (See:
Starting and Charging/Testing and Inspection/Component Tests and General Diagnostics/Battery Inspection/Test).
* A misfire DTC could be caused by an excessive vibration from sources other than the engine. Inspect the following for possible sources of
vibration:
- A tire or wheel that is out of round or balance
- Variable thickness brake rotors
- An unbalanced drive shaft
- Certain rough road conditions
- A damaged accessory drive component or belt
- A damaged reluctor wheel
- The Crankshaft Position System Variation Learn procedure may need to be performed.
Reference Information
Schematic Reference
Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Sunday, June 28, 2020
2010 Cadillac Truck Escalade RWD V8-6.2L Page 1950
2010 Cadillac Truck Escalade RWD V8-6.2L Page 1950
DTC P0120, P0122, P0123, P0220, P0222, P0223, or P2135
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC P0120
- Throttle Position (TP) Sensor 1 Circuit
DTC P0122
- Throttle Position (TP) Sensor 1 Circuit Low Voltage
DTC P0123
- Throttle Position (TP) Sensor 1 Circuit High Voltage
DTC P0220
- Throttle Position (TP) Sensor 2 Circuit
DTC P0222
- Throttle Position (TP) Sensor 2 Circuit Low Voltage
DTC P0223
- Throttle Position (TP) Sensor 2 Circuit High Voltage
DTC P2135
- Throttle Position (TP) Sensor 1-2 Correlation
Diagnostic Fault Information
Typical Scan Tool Data
DTC P0120, P0122, P0123, P0220, P0222, P0223, or P2135
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC P0120
- Throttle Position (TP) Sensor 1 Circuit
DTC P0122
- Throttle Position (TP) Sensor 1 Circuit Low Voltage
DTC P0123
- Throttle Position (TP) Sensor 1 Circuit High Voltage
DTC P0220
- Throttle Position (TP) Sensor 2 Circuit
DTC P0222
- Throttle Position (TP) Sensor 2 Circuit Low Voltage
DTC P0223
- Throttle Position (TP) Sensor 2 Circuit High Voltage
DTC P2135
- Throttle Position (TP) Sensor 1-2 Correlation
Diagnostic Fault Information
Typical Scan Tool Data
Sunday, June 21, 2020
2010 Cadillac Truck Escalade RWD V8-6.2L Page 1792
2010 Cadillac Truck Escalade RWD V8-6.2L Page 1792
P0134, P0135, P0137, P0138, P013A, P013B, P013E, P013F, P0140, P0141, P0171, P0172, P0201, P0202, P0203, P0204, P0220, P0222,
P0223, P0300, P0442, P0443, P0446, P0449, P0455, P0496, P1133, P1174, P1516, P2101, P2119, P2135, P2176, P2270, P2271, P2A00 are
not set.
* The ignition 1 voltage is between 10-32 V.
* The learned heater resistance is valid.
* The fuel level is greater than 10 %.
* The engine run time is equal to or greater than 5 minutes.
* The DTCs run once per ignition cycle when the above conditions are met.
Conditions for Setting the DTC
P0133 or P0153
* The ECM detects that the HO2S 1 rich-to-lean or lean-to-rich average response time is greater than a calibrated value.
* The DTCs set within 100 s when the above condition is met.
P013A or P013C
The ECM detects that the accumulated mass air flow monitored during rich-to-lean transitions between 450-150 mV is greater than 75 grams.
P013B or P013D
The ECM detects that the accumulated mass air flow monitored during lean-to-rich transitions between 350-650 mV is greater than 75 grams.
P013E or P014A
The ECM detects that the O2 sensor voltage has not decreased below 450 mV within 42 grams of accumulated air flow.
P013F or P014B
The ECM detects that the O2 sensor voltage has not increased above 350 mV within 200 grams of accumulated air flow.
P1133 or P1153
* The ECM detects that the HO2S 1 rich-to-lean counts, or the lean-to-rich counts are less than a calibrated value.
* The DTCs set within 100 s when the above condition is met.
Action Taken When the DTC Sets
DTCs P0133, P013A, P013B, P013C, P013D, P013E, P013F, P014A, P014B, P0153, P1133, and P1153 are Type B DTCs.
Conditions for Clearing the DTC
DTCs P0133, P013A, P013B, P013C, P013D, P013E, P013F, P014A, P014B, P0153, P1133, and P1153 are Type B DTCs.
Reference Information
Schematic Reference
Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
* Heated Oxygen Sensor Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical
Diagnostic Procedures/Wiring Repairs/Heated Oxygen Sensor Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
P0134, P0135, P0137, P0138, P013A, P013B, P013E, P013F, P0140, P0141, P0171, P0172, P0201, P0202, P0203, P0204, P0220, P0222,
P0223, P0300, P0442, P0443, P0446, P0449, P0455, P0496, P1133, P1174, P1516, P2101, P2119, P2135, P2176, P2270, P2271, P2A00 are
not set.
* The ignition 1 voltage is between 10-32 V.
* The learned heater resistance is valid.
* The fuel level is greater than 10 %.
* The engine run time is equal to or greater than 5 minutes.
* The DTCs run once per ignition cycle when the above conditions are met.
Conditions for Setting the DTC
P0133 or P0153
* The ECM detects that the HO2S 1 rich-to-lean or lean-to-rich average response time is greater than a calibrated value.
* The DTCs set within 100 s when the above condition is met.
P013A or P013C
The ECM detects that the accumulated mass air flow monitored during rich-to-lean transitions between 450-150 mV is greater than 75 grams.
P013B or P013D
The ECM detects that the accumulated mass air flow monitored during lean-to-rich transitions between 350-650 mV is greater than 75 grams.
P013E or P014A
The ECM detects that the O2 sensor voltage has not decreased below 450 mV within 42 grams of accumulated air flow.
P013F or P014B
The ECM detects that the O2 sensor voltage has not increased above 350 mV within 200 grams of accumulated air flow.
P1133 or P1153
* The ECM detects that the HO2S 1 rich-to-lean counts, or the lean-to-rich counts are less than a calibrated value.
* The DTCs set within 100 s when the above condition is met.
Action Taken When the DTC Sets
DTCs P0133, P013A, P013B, P013C, P013D, P013E, P013F, P014A, P014B, P0153, P1133, and P1153 are Type B DTCs.
Conditions for Clearing the DTC
DTCs P0133, P013A, P013B, P013C, P013D, P013E, P013F, P014A, P014B, P0153, P1133, and P1153 are Type B DTCs.
Reference Information
Schematic Reference
Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
* Heated Oxygen Sensor Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical
Diagnostic Procedures/Wiring Repairs/Heated Oxygen Sensor Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Thursday, April 16, 2020
2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1818
2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1818
瀚慖f a DTC P0121, P0122, P0123, P0221, P0222, or P0223 set while performing this procedure, refer to DTC P0121-P0123 or
P0221-P0223 (Without LF1, LFW) (See: P Code Charts/P0121) for further diagnosis.
5. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the
conditions that you observed from the Freeze Frame/Failure Records data.
Circuit/System Testing
1. Inspect the Q38 throttle body for the following conditions:
* A throttle blade that is not in the rest position
* A throttle valve that is binding open or closed
* A throttle valve that opens or closes without spring pressure
瀚慖f a condition is found, replace the Q38 throttle body.
Note: Disconnecting the throttle body harness connector causes additional DTCs to set.
2. Ignition OFF, disconnect the harness connector of the Q38 throttle body.
3. Ignition ON, test for 4.0-4.2 V between the TAC motor control 1 circuit terminal B and ground.
瀚慖f voltage is greater than the specified range, test each of the motor control circuits for a short to voltage. If the circuits tests normal,
replace the K20 Engine Control Module.
瀚慖f voltage is less than the specified range, test the motor control 1 circuit for a short to ground or an open/high resistance. If the circuit
tests normal, replace the K20 Engine Control Module.
4. Connect a test lamp between the TAC motor control 2 circuit terminal A and B+. The test lamp should NOT illuminate.
瀚慖f the test lamp illuminates, test the control circuit for a short to ground. If the circuit tests normal, replace the K20 Engine Control
Module.
5. Test for greater than 3.5 V between TAC motor control 1 circuit terminal B and TAC motor control 2 circuit terminal A.
瀚慖f the voltage is less than the specified value, test the motor control 2 circuit for an open/high resistance. If the circuit tests normal,
replace the K20 Engine Control Module.
6. Ignition OFF, connect the EL 34730-405 - Injector Test Lamp between the TAC motor control 1 circuit terminal B and TAC motor control 2
circuit terminal A of the throttle body harness connector. Observe the injector test lamp while turning the ignition ON for 5 s and then OFF.
Verify the injector test lamp illuminates brightly and then turns OFF.
瀚慖f the injector test lamp does not illuminate, replace the K20 Engine Control Module.
7. If all circuits test normal, replace the Q38 throttle body.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Throttle Body Assembly Replacement (LF1) (See: Powertrain Management/Fuel Delivery and Air Induction/Throttle Body/Service and
Repair/Removal and Replacement)Throttle Body Assembly Replacement (LAU) (See: Powertrain Management/Fuel Delivery and Air
Induction/Throttle Body/Service and Repair/Removal and Replacement)
* Control Module References (See: Testing and Inspection/Programming and Relearning) for Engine Control Module replacement, setup, and
programming
P2103
DTC P0638, P2100-P2103, or P2119 (Without LF1, LFW)
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
Thursday, March 12, 2020
2010 Cadillac CTS Sedan AWD V6-3.6L Page 1927
2010 Cadillac CTS Sedan AWD V6-3.6L Page 1927
P0204, P0205, P0206, P0221, P0222, P0223, P0261, P0262, P0264, P0265, P0267, P0268, P0270, P0271, P0273, P0300, P0301, P0302,
P0303, P0304, P0305, P0306, P0335, P0336, P0338, P0443, P0458, P0459, P0461, P0462, P0463, P2068 P2088, P2089, P2090, P2091,
P2092, P2093, P2094, P2095 P2146, P2149, P2152, P2155, P216A, and P216D must run and pass.
* The engine speed is between 519-1,001 RPM.
* The engine load is between 0-24 %.
* The throttle angle is less than 100 %.
* The cold start fuel control is not active.
* The Closed Loop fuel control is enabled.
* The engine is not in decel fuel cut-off.
* The engine coolant temperature (ECT) is warmer than 60掳C (140掳F).
* The intake air temperature (IAT) is colder than 61掳C (142掳F).
* The calculated amount of fuel metered into the engine is greater than 700 g.
* DTCs P2188 and P2190 run continuously when the above conditions are met for approximately 300 s, after Closed Loop fuel control is
enabled.
Conditions for Setting the DTC
P2178 or P2180
The Long Term Fuel Trim Cruise/Accel is less than -22 % for 4 s or for a cumulative of 30 s.
P2188 or P2190
The Long Term Fuel Trim Idle/Decel is less than -6 % for 4 s or for a cumulative of 30 s.
Action Taken When the DTC Sets
DTCs P2178, P2180, P2188, and P2190 are Type B DTCs.
Conditions for Clearing the MIL/DTC
DTCs P2178, P2180, P2188, and P2190 are Type B DTCs.
Diagnostic Aids
* An HO2S will not cause this DTC to set without the occurrence of circuit related HO2S DTCs. Do not replace an HO2S to address this DTC.
* Observing the LT FT Bn 1 and Bn 2 parameters, while driving the vehicle can determine whether the rich condition is effecting only one
bank , or is common to both banks of the engine.
* A fuel system delivery condition causes this DTC to set. Thoroughly inspect all items that cause a rich condition. Refer to Fuel System
Diagnosis (See: Powertrain Management/Computers and Control Systems/Testing and Inspection/Component Tests and General
Diagnostics/Fuel System Diagnosis).
* Review the Freeze Frame/Failure Records with a scan tool.
Reference Information
Schematic Reference
Engine Controls Schematics (LLT) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics
(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit
Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Wiring Repairs/Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Verification
1. Observe the DTC information with a scan tool. DTC P2178, P2180, P2188, or P2190 should not be set.
Tuesday, March 3, 2020
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 2786
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 2786
P0134, P0135, P0137, P0138, P013A, P013B, P013E, P013F, P0140, P0141, P0171, P0172, P0201, P0202, P0203, P0204, P0220, P0222,
P0223, P0300, P0442, P0443, P0446, P0449, P0455, P0496, P1133, P1174, P1516, P2101, P2119, P2135, P2176, P2270, P2271, P2A00 are
not set.
* The ignition 1 voltage is between 10-18 volts.
* The learned heater resistance is valid.
* The fuel level is greater than 10 percent.
* The engine run time is equal to or greater than 5 minutes.
* The accelerator pedal (APP) is steady.
* The torque converter clutch (TCC) is applied.
* DTC P013A runs once per ignition cycle, during decel fuel cut-off (DFCO), when the above conditions are met.
P013B P013D, P013F, or P014B
* Before the ECM can report DTC P013B, or P013D failed, DTCs P013A, P013C, P013E, P013F, P014A, P014B, P2270, P2271, P2272, and
P2273 must run and pass.
* Before the ECM can report DTC P013F, or P014B failed, DTCs P013A, P013C, P013E, P014A, P2270, P2271, P2272, and P2273 must run
and pass.
* DTCs P0030, P0036, P0053, P0054, P0101, P0102, P0103, P0106, P0107, P0108, P0120, P0121, P0122, P0123, P0131, P0132, P0133,
P0134, P0135, P0137, P0138, P013A, P013B, P013E, P013F, P0140, P0141, P0171, P0172, P0201, P0202, P0203, P0204, P0220, P0222,
P0223, P0300, P0442, P0443, P0446, P0449, P0455, P0496, P1133, P1174, P1516, P2101, P2119, P2135, P2176, P2270, P2271, P2A00 are
not set.
* The ignition 1 voltage is between 10-18 volts.
* The learned heater resistance is valid.
* The fuel level is greater than 10 percent.
* The engine run time is equal to or greater than 5 minutes.
* DTC P013B runs once per ignition cycle when the above conditions are met.
Conditions for Setting the DTC
P0133 or P0153
* The ECM detects that the HO2S 1 rich-to-lean or lean-to-rich average response time is greater than a calibrated value.
* The DTCs set within 100 seconds when the above condition is met.
P013A or P013C
The ECM detects that the accumulated mass air flow monitored during rich-to-lean transitions between 450-150 mV is greater than 75 grams.
P013B or P013D
The ECM detects that the accumulated mass air flow monitored during lean-to-rich transitions between 350-650 mV is greater than 75 grams.
P013E or P014A
The ECM detects that the O2 sensor voltage has not decreased below 450 mV within 42 grams of accumulated air flow.
P013F or P014B
The ECM detects that the O2 sensor voltage has not increased above 350 mV within 200 grams of accumulated air flow.
P1133 or P1153
* The ECM detects that the HO2S 1 rich-to-lean counts, or the lean-to-rich counts are less than a calibrated value.
* The DTCs set within 100 seconds when the above condition is met.
Action Taken When the DTC Sets
DTCs P0133, P013A, P013B, P013C, P013D, P013E, P013F, P014A, P014B, P0153, P1133, and P1153 are Type B DTCs.
Conditions for Clearing the DTC
DTCs P0133, P013A, P013B, P013C, P013D, P013E, P013F, P014A, P014B, P0153, P1133, and P1153 are Type B DTCs.
Reference Information
Schematic Reference
Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
P0134, P0135, P0137, P0138, P013A, P013B, P013E, P013F, P0140, P0141, P0171, P0172, P0201, P0202, P0203, P0204, P0220, P0222,
P0223, P0300, P0442, P0443, P0446, P0449, P0455, P0496, P1133, P1174, P1516, P2101, P2119, P2135, P2176, P2270, P2271, P2A00 are
not set.
* The ignition 1 voltage is between 10-18 volts.
* The learned heater resistance is valid.
* The fuel level is greater than 10 percent.
* The engine run time is equal to or greater than 5 minutes.
* The accelerator pedal (APP) is steady.
* The torque converter clutch (TCC) is applied.
* DTC P013A runs once per ignition cycle, during decel fuel cut-off (DFCO), when the above conditions are met.
P013B P013D, P013F, or P014B
* Before the ECM can report DTC P013B, or P013D failed, DTCs P013A, P013C, P013E, P013F, P014A, P014B, P2270, P2271, P2272, and
P2273 must run and pass.
* Before the ECM can report DTC P013F, or P014B failed, DTCs P013A, P013C, P013E, P014A, P2270, P2271, P2272, and P2273 must run
and pass.
* DTCs P0030, P0036, P0053, P0054, P0101, P0102, P0103, P0106, P0107, P0108, P0120, P0121, P0122, P0123, P0131, P0132, P0133,
P0134, P0135, P0137, P0138, P013A, P013B, P013E, P013F, P0140, P0141, P0171, P0172, P0201, P0202, P0203, P0204, P0220, P0222,
P0223, P0300, P0442, P0443, P0446, P0449, P0455, P0496, P1133, P1174, P1516, P2101, P2119, P2135, P2176, P2270, P2271, P2A00 are
not set.
* The ignition 1 voltage is between 10-18 volts.
* The learned heater resistance is valid.
* The fuel level is greater than 10 percent.
* The engine run time is equal to or greater than 5 minutes.
* DTC P013B runs once per ignition cycle when the above conditions are met.
Conditions for Setting the DTC
P0133 or P0153
* The ECM detects that the HO2S 1 rich-to-lean or lean-to-rich average response time is greater than a calibrated value.
* The DTCs set within 100 seconds when the above condition is met.
P013A or P013C
The ECM detects that the accumulated mass air flow monitored during rich-to-lean transitions between 450-150 mV is greater than 75 grams.
P013B or P013D
The ECM detects that the accumulated mass air flow monitored during lean-to-rich transitions between 350-650 mV is greater than 75 grams.
P013E or P014A
The ECM detects that the O2 sensor voltage has not decreased below 450 mV within 42 grams of accumulated air flow.
P013F or P014B
The ECM detects that the O2 sensor voltage has not increased above 350 mV within 200 grams of accumulated air flow.
P1133 or P1153
* The ECM detects that the HO2S 1 rich-to-lean counts, or the lean-to-rich counts are less than a calibrated value.
* The DTCs set within 100 seconds when the above condition is met.
Action Taken When the DTC Sets
DTCs P0133, P013A, P013B, P013C, P013D, P013E, P013F, P014A, P014B, P0153, P1133, and P1153 are Type B DTCs.
Conditions for Clearing the DTC
DTCs P0133, P013A, P013B, P013C, P013D, P013E, P013F, P014A, P014B, P0153, P1133, and P1153 are Type B DTCs.
Reference Information
Schematic Reference
Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Friday, February 14, 2020
2010 Cadillac CTS Sedan AWD V6-3.6L Page 1403
2010 Cadillac CTS Sedan AWD V6-3.6L Page 1403
P0152, P0153, P0155, P0157, P0158, P0160, P0161, P0221, P0222, P0223, P0335, P0336, P0338, P2096, P2097, P2098, P2099, P2195,
P2196, P2197, P2198, P2232, P2235, P2237, P2240, P2243, P2247, P2251, P2254, P2270, P2271, P2272, P2273, P2297, P2298, P2626, and
P2629 must run and pass.
* DTC P000A, P000B, P000C, P000D, P0010, P0011, P0013, P0014, P0020, P0021, P0023, P0024, P0030, P0031, P0032, P0050, P0051,
P0052, P0100, P0101, P0102, P0103, P0116, P0117, P0118, P0119, P0121, P0122, P0123, P0128, P013A, P013C, P013E, P0130, P0131,
P0132, P0133, P0135, P0137, P0138, P014A, P0140, P0141, P0150, P0151, P0152, P0153, P0155, P0157, P0158, P0160, P0161, P0221,
P0222, P0223, P0300, P0301-P0306, P0443, P0455, P0458, P0459, P0496, P2088, P2089, P2090, P2091, P2092, P2093, P2094, P2095,
P2096, P2097, P2098, P2099, P2100, P2101, P2107, P2119, P2122, P2123, P2127, P2128, P2138, P2176, P2177, P2178, P2179, P2180,
P2187, P2188, P2189, P2190, P2232, P2235, P2270, P2271, P2272, or P2273 is not set.
* The engine speed is 1,080-3,000 RPM, or 1,160-2,440 RPM for LLT.
* The engine load is 13-45 percent, or 13-80 percent for LLT.
* The air flow into the engine is between 4-20 g/s and steady, or 3-28 g/s for LLT.
* The engine intake air temperature (IAT) is warmer than -30掳C (-22掳F).
* The HO2S 2 is at operating temperature for greater than a range of 140-300 seconds, or 140-210 seconds for LLT.
* The engine is operating in Closed Loop.
* The calculated TWC temperature is between 480-750掳C (896-1,382掳F) and steady, 500-900掳C (932-1,652掳F) for LLT.
* The difference between the expected TWC temperature and the calculated TWC temperature is less than 40掳C (72掳F).
* The difference between the expected exhaust gas mass flow and the calculated exhaust gas mass flow is less than 11 g/s.
* The above conditions exist for approximately 17 minutes.
* DTCs P0420 and P0430 run once a drive cycle. The ECM will attempt to run this diagnostic up to 3 times per drive cycle.
Conditions for Setting the DTC
The ECM determines the oxygen storage capacity (OSC) of the catalyst has degraded below a calibrated threshold for greater than 5 seconds.
Action Taken When the DTC Sets
DTCs P0420 and P0430 are Type A DTCs.
Conditions for Clearing the DTC
DTCs P0420 and P0430 are Type A DTCs.
Diagnostic Aids
Inspect for the following conditions, which may cause a catalytic converter to degrade:
* An engine misfire
* High engine oil or high coolant consumption
* Retarded spark timing
* A weak or poor spark
* A lean fuel mixture
* A rich fuel mixture
* A damaged oxygen sensor or wiring harness
Reference Information
Schematic Reference
Engine Controls Schematics (LLT) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics
(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit
Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Wiring Repairs/Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Testing
Tuesday, December 17, 2019
2010 Cadillac Truck Escalade AWD V8-6.2L Page 2087
P0220, P0222, P0223, P0335, P0336, P0606, P0641, P0651, P1516, P2101, P2120, P2122, P2123, P2125, P2127, P2128, P2135, P2138, and
P2176 are not set.
* When DTC P0315 is set, the engine speed must be more than 1,000 RPM.
* Engine run time is more than 2 crankshaft revolutions.
* The engine speed is between 375-5,600 RPM.
* The ignition voltage is between 9-18 volts.
* The engine coolant temperature (ECT) is between -7 and +130锟斤拷C (+19 and +266锟斤拷F).
* When the startup ECT is colder than -7锟斤拷C (+19锟斤拷F), this diagnostic will be delayed until the ECT is warmer than +21锟斤拷C (+69锟斤拷F).
* The fuel level is more than 10 percent.
* The ECM is not in fuel shut-off, or decel fuel cut-off mode.
* The electronic brake control module (EBCM) and the traction control system (TCS) are not active or detecting rough road.
* An automatic transmission shift with a throttle position more than 95 percent is not occuring.
* The power management is not active.
* Excessive drive wheel slip is not detected.
* The power take-off (PTO) is disabled, where applicable.
* The cylinder deactivation is not in progress, where applicable.
* DTCs P0300-P0308 run continuously when the above conditions are met.
Conditions for Setting the DTC
DTC P0300
The ECM is detecting a crankshaft speed change indicating a random misfire is occuring that exceeds mandated emission level standards or is at
catalytic converter damaging levels.
DTC P0301, P0302, P0303, P0304, P0305, P0306, P0307, or P0308
The ECM is detecting a crankshaft speed change indicating a single cylinder misfire is occuring that exceeds mandated emission level standards or
is at catalytic converter damaging levels.
Action Taken When the DTC Sets
* DTCs P0300-P0308 are Type B DTCs.
* When the MIL is flashing the fuel injector may be disabled for the misfiring cylinder to protect the catalytic converter.
* Depending on the conditions that set the DTC, the engine may go into Open Loop.
Conditions for Clearing the MIL/DTC
* DTCs P0300-P0308 are Type B DTCs.
* The DTC must run and pass under the same operating conditions that were present when the DTC failed.
Diagnostic Aids
* Ensure that each fuel injector is connected to the proper fuel injector harness connector.
* A misfire may only occur when the engine is operating under a load or when the engine is cold.
* A high resistance condition on any ignition control (IC) circuit can cause an engine misfire P0300-P0308 DTC to set without setting an IC
circuit P0351-P0358 DTC.
* This test procedure requires that the vehicle battery has passed a load test and is completely charged. Refer to Battery Inspection/Test (See:
Starting and Charging/Testing and Inspection/Component Tests and General Diagnostics/Battery Inspection/Test).
* A misfire DTC could be caused by an excessive vibration from sources other than the engine. Inspect the following for possible sources of
vibration:
- A tire or wheel that is out of round or balance
- Variable thickness brake rotors
- An unbalanced drive shaft
- Certain rough road conditions
- A damaged accessory drive component or belt
- A damaged reluctor wheel
- The Crankshaft Position System Variation Learn procedure may need to be performed.
Reference Information
Schematic Reference
Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
P2176 are not set.
* When DTC P0315 is set, the engine speed must be more than 1,000 RPM.
* Engine run time is more than 2 crankshaft revolutions.
* The engine speed is between 375-5,600 RPM.
* The ignition voltage is between 9-18 volts.
* The engine coolant temperature (ECT) is between -7 and +130锟斤拷C (+19 and +266锟斤拷F).
* When the startup ECT is colder than -7锟斤拷C (+19锟斤拷F), this diagnostic will be delayed until the ECT is warmer than +21锟斤拷C (+69锟斤拷F).
* The fuel level is more than 10 percent.
* The ECM is not in fuel shut-off, or decel fuel cut-off mode.
* The electronic brake control module (EBCM) and the traction control system (TCS) are not active or detecting rough road.
* An automatic transmission shift with a throttle position more than 95 percent is not occuring.
* The power management is not active.
* Excessive drive wheel slip is not detected.
* The power take-off (PTO) is disabled, where applicable.
* The cylinder deactivation is not in progress, where applicable.
* DTCs P0300-P0308 run continuously when the above conditions are met.
Conditions for Setting the DTC
DTC P0300
The ECM is detecting a crankshaft speed change indicating a random misfire is occuring that exceeds mandated emission level standards or is at
catalytic converter damaging levels.
DTC P0301, P0302, P0303, P0304, P0305, P0306, P0307, or P0308
The ECM is detecting a crankshaft speed change indicating a single cylinder misfire is occuring that exceeds mandated emission level standards or
is at catalytic converter damaging levels.
Action Taken When the DTC Sets
* DTCs P0300-P0308 are Type B DTCs.
* When the MIL is flashing the fuel injector may be disabled for the misfiring cylinder to protect the catalytic converter.
* Depending on the conditions that set the DTC, the engine may go into Open Loop.
Conditions for Clearing the MIL/DTC
* DTCs P0300-P0308 are Type B DTCs.
* The DTC must run and pass under the same operating conditions that were present when the DTC failed.
Diagnostic Aids
* Ensure that each fuel injector is connected to the proper fuel injector harness connector.
* A misfire may only occur when the engine is operating under a load or when the engine is cold.
* A high resistance condition on any ignition control (IC) circuit can cause an engine misfire P0300-P0308 DTC to set without setting an IC
circuit P0351-P0358 DTC.
* This test procedure requires that the vehicle battery has passed a load test and is completely charged. Refer to Battery Inspection/Test (See:
Starting and Charging/Testing and Inspection/Component Tests and General Diagnostics/Battery Inspection/Test).
* A misfire DTC could be caused by an excessive vibration from sources other than the engine. Inspect the following for possible sources of
vibration:
- A tire or wheel that is out of round or balance
- Variable thickness brake rotors
- An unbalanced drive shaft
- Certain rough road conditions
- A damaged accessory drive component or belt
- A damaged reluctor wheel
- The Crankshaft Position System Variation Learn procedure may need to be performed.
Reference Information
Schematic Reference
Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
2010 Cadillac Truck Escalade AWD V8-6.2L Page 2051
DTC P0120, P0122, P0123, P0220, P0222, P0223, or P2135
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC P0120
- Throttle Position (TP) Sensor 1 Circuit
DTC P0122
- Throttle Position (TP) Sensor 1 Circuit Low Voltage
DTC P0123
- Throttle Position (TP) Sensor 1 Circuit High Voltage
DTC P0220
- Throttle Position (TP) Sensor 2 Circuit
DTC P0222
- Throttle Position (TP) Sensor 2 Circuit Low Voltage
DTC P0223
- Throttle Position (TP) Sensor 2 Circuit High Voltage
DTC P2135
- Throttle Position (TP) Sensor 1-2 Correlation
Diagnostic Fault Information
Typical Scan Tool Data
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC P0120
- Throttle Position (TP) Sensor 1 Circuit
DTC P0122
- Throttle Position (TP) Sensor 1 Circuit Low Voltage
DTC P0123
- Throttle Position (TP) Sensor 1 Circuit High Voltage
DTC P0220
- Throttle Position (TP) Sensor 2 Circuit
DTC P0222
- Throttle Position (TP) Sensor 2 Circuit Low Voltage
DTC P0223
- Throttle Position (TP) Sensor 2 Circuit High Voltage
DTC P2135
- Throttle Position (TP) Sensor 1-2 Correlation
Diagnostic Fault Information
Typical Scan Tool Data
Wednesday, November 27, 2019
2010 Cadillac CTS Sedan AWD V6-3.6L Page 1200
2010 Cadillac CTS Sedan AWD V6-3.6L Page 1200
P0222
DTC P0121-P0123 or P0221-P0223 (Without LF1)
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC P0121
- Throttle Position Sensor 1 Performance
DTC P0122
- Throttle Position Sensor 1 Circuit Low Voltage
DTC P0123
- Throttle Position Sensor 1 Circuit High Voltage
DTC P0221
- Throttle Position Sensor 2 Performance
DTC P0222
- Throttle Position Sensor 2 Circuit Low Voltage
DTC P0223
- Throttle Position Sensor 2 Circuit High Voltage
Diagnostic Fault Information
Typical Scan Tool Data
Circuit/System Description
The throttle body assembly contains 2 throttle position sensors. The TP sensors are mounted to the throttle body assembly and are not serviceable.
The TP sensors provide a signal voltage that changes relative to throttle blade angle. The Engine Control Module (ECM) supplies the TP sensors
with a common 5 V reference circuit , a common low reference circuit, and two independent signal circuits. The TP sensors have opposite
functionality. TP sensor 1 signal voltage decreases from greater than 4 V at idle to less than 1 V at wide open throttle (WOT). TP sensor 2 signal
voltage increases from less than 1 V at idle to greater than 4 V at WOT.
Saturday, November 2, 2019
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1893
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1893
P0134, P0135, P0137, P0138, P013A, P013B, P013E, P013F, P0140, P0141, P0171, P0172, P0201, P0202, P0203, P0204, P0220, P0222,
P0223, P0300, P0442, P0443, P0446, P0449, P0455, P0496, P1133, P1174, P1516, P2101, P2119, P2135, P2176, P2270, P2271, P2A00 are
not set.
* The ignition 1 voltage is between 10-32 V.
* The learned heater resistance is valid.
* The fuel level is greater than 10 %.
* The engine run time is equal to or greater than 5 minutes.
* The DTCs run once per ignition cycle when the above conditions are met.
Conditions for Setting the DTC
P0133 or P0153
* The ECM detects that the HO2S 1 rich-to-lean or lean-to-rich average response time is greater than a calibrated value.
* The DTCs set within 100 s when the above condition is met.
P013A or P013C
The ECM detects that the accumulated mass air flow monitored during rich-to-lean transitions between 450-150 mV is greater than 75 grams.
P013B or P013D
The ECM detects that the accumulated mass air flow monitored during lean-to-rich transitions between 350-650 mV is greater than 75 grams.
P013E or P014A
The ECM detects that the O2 sensor voltage has not decreased below 450 mV within 42 grams of accumulated air flow.
P013F or P014B
The ECM detects that the O2 sensor voltage has not increased above 350 mV within 200 grams of accumulated air flow.
P1133 or P1153
* The ECM detects that the HO2S 1 rich-to-lean counts, or the lean-to-rich counts are less than a calibrated value.
* The DTCs set within 100 s when the above condition is met.
Action Taken When the DTC Sets
DTCs P0133, P013A, P013B, P013C, P013D, P013E, P013F, P014A, P014B, P0153, P1133, and P1153 are Type B DTCs.
Conditions for Clearing the DTC
DTCs P0133, P013A, P013B, P013C, P013D, P013E, P013F, P014A, P014B, P0153, P1133, and P1153 are Type B DTCs.
Reference Information
Schematic Reference
Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
* Heated Oxygen Sensor Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical
Diagnostic Procedures/Wiring Repairs/Heated Oxygen Sensor Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
P0134, P0135, P0137, P0138, P013A, P013B, P013E, P013F, P0140, P0141, P0171, P0172, P0201, P0202, P0203, P0204, P0220, P0222,
P0223, P0300, P0442, P0443, P0446, P0449, P0455, P0496, P1133, P1174, P1516, P2101, P2119, P2135, P2176, P2270, P2271, P2A00 are
not set.
* The ignition 1 voltage is between 10-32 V.
* The learned heater resistance is valid.
* The fuel level is greater than 10 %.
* The engine run time is equal to or greater than 5 minutes.
* The DTCs run once per ignition cycle when the above conditions are met.
Conditions for Setting the DTC
P0133 or P0153
* The ECM detects that the HO2S 1 rich-to-lean or lean-to-rich average response time is greater than a calibrated value.
* The DTCs set within 100 s when the above condition is met.
P013A or P013C
The ECM detects that the accumulated mass air flow monitored during rich-to-lean transitions between 450-150 mV is greater than 75 grams.
P013B or P013D
The ECM detects that the accumulated mass air flow monitored during lean-to-rich transitions between 350-650 mV is greater than 75 grams.
P013E or P014A
The ECM detects that the O2 sensor voltage has not decreased below 450 mV within 42 grams of accumulated air flow.
P013F or P014B
The ECM detects that the O2 sensor voltage has not increased above 350 mV within 200 grams of accumulated air flow.
P1133 or P1153
* The ECM detects that the HO2S 1 rich-to-lean counts, or the lean-to-rich counts are less than a calibrated value.
* The DTCs set within 100 s when the above condition is met.
Action Taken When the DTC Sets
DTCs P0133, P013A, P013B, P013C, P013D, P013E, P013F, P014A, P014B, P0153, P1133, and P1153 are Type B DTCs.
Conditions for Clearing the DTC
DTCs P0133, P013A, P013B, P013C, P013D, P013E, P013F, P014A, P014B, P0153, P1133, and P1153 are Type B DTCs.
Reference Information
Schematic Reference
Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
* Heated Oxygen Sensor Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical
Diagnostic Procedures/Wiring Repairs/Heated Oxygen Sensor Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Subscribe to:
Posts (Atom)