2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1720
1. Observe the DTC information with a scan tool. DTC P0601, P0602, P0603, P0604, P0606, P0607, P060D, P062F, or P2610 should not set.
2. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the
conditions that you observed from the Freeze Frame/Failure Records data.
Circuit/System Testing
1. Observe the DTC information with a scan tool.
瀚慖f DTC P0602 is set, attempt to program the K20 ECM before replacing the K20 ECM. Refer to Control Module References (See:
Testing and Inspection/Programming and Relearning) for K20 ECM replacement, setup, and programming.
瀚慖f DTC P0602 resets, replace the K20 ECM.
2. Observe the DTC information with a scan tool. DTC P0601, P0603, P0604, P0605, P0606, P0607, P060D, P062F, or P2610 should not set.
瀚慖f a DTC failed this ignition, replace the K20 ECM.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, programming and setup
Fuel Pump Control Module
DTC P0601-P0604, P0606, or P062F
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions)provides an overview of each diagnostic category.
DTC Descriptors
DTC P0601
- Control Module Read Only Memory (ROM)
DTC P0602
- Control Module Not Programmed
DTC P0603
- Control Module Long Term Memory Reset
DTC P0604
- Control Module Random Access Memory (RAM)
DTC P0606
- Control Module Internal Performance
DTC P062F
- Control Module Long Term Memory Performance
Circuit/System Description
The internal fault detection is handled inside the fuel pump control module. No external circuits are involved.
Conditions for Running the DTC
The fuel pump control module runs the program to detect an internal fault when power up is commanded. The only requirements are voltage and
ground. This program runs even if the voltage is out of the valid operating range.
Conditions for Setting the DTC
The fuel pump control module has detected an internal malfunction.
Showing posts with label or P2610 should not set.. Show all posts
Showing posts with label or P2610 should not set.. Show all posts
Thursday, October 29, 2020
Thursday, June 18, 2020
2010 Cadillac Truck Escalade RWD V8-6.2L Page 1720
2010 Cadillac Truck Escalade RWD V8-6.2L Page 1720
1. Observe the DTC information with a scan tool. DTC P0601, P0602, P0603, P0604, P0606, P0607, P060D, P062F, or P2610 should not set.
2. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the
conditions that you observed from the Freeze Frame/Failure Records data.
Circuit/System Testing
1. Observe the DTC information with a scan tool.
瀚慖f DTC P0602 is set, attempt to program the K20 ECM before replacing the K20 ECM. Refer to Control Module References (See:
Testing and Inspection/Programming and Relearning) for K20 ECM replacement, setup, and programming.
瀚慖f DTC P0602 resets, replace the K20 ECM.
2. Observe the DTC information with a scan tool. DTC P0601, P0603, P0604, P0605, P0606, P0607, P060D, P062F, or P2610 should not set.
瀚慖f a DTC failed this ignition, replace the K20 ECM.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, programming and setup
Fuel Pump Control Module
DTC P0601-P0604, P0606, or P062F
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions)provides an overview of each diagnostic category.
DTC Descriptors
DTC P0601
- Control Module Read Only Memory (ROM)
DTC P0602
- Control Module Not Programmed
DTC P0603
- Control Module Long Term Memory Reset
DTC P0604
- Control Module Random Access Memory (RAM)
DTC P0606
- Control Module Internal Performance
DTC P062F
- Control Module Long Term Memory Performance
Circuit/System Description
The internal fault detection is handled inside the fuel pump control module. No external circuits are involved.
Conditions for Running the DTC
The fuel pump control module runs the program to detect an internal fault when power up is commanded. The only requirements are voltage and
ground. This program runs even if the voltage is out of the valid operating range.
Conditions for Setting the DTC
The fuel pump control module has detected an internal malfunction.
1. Observe the DTC information with a scan tool. DTC P0601, P0602, P0603, P0604, P0606, P0607, P060D, P062F, or P2610 should not set.
2. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the
conditions that you observed from the Freeze Frame/Failure Records data.
Circuit/System Testing
1. Observe the DTC information with a scan tool.
瀚慖f DTC P0602 is set, attempt to program the K20 ECM before replacing the K20 ECM. Refer to Control Module References (See:
Testing and Inspection/Programming and Relearning) for K20 ECM replacement, setup, and programming.
瀚慖f DTC P0602 resets, replace the K20 ECM.
2. Observe the DTC information with a scan tool. DTC P0601, P0603, P0604, P0605, P0606, P0607, P060D, P062F, or P2610 should not set.
瀚慖f a DTC failed this ignition, replace the K20 ECM.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, programming and setup
Fuel Pump Control Module
DTC P0601-P0604, P0606, or P062F
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions)provides an overview of each diagnostic category.
DTC Descriptors
DTC P0601
- Control Module Read Only Memory (ROM)
DTC P0602
- Control Module Not Programmed
DTC P0603
- Control Module Long Term Memory Reset
DTC P0604
- Control Module Random Access Memory (RAM)
DTC P0606
- Control Module Internal Performance
DTC P062F
- Control Module Long Term Memory Performance
Circuit/System Description
The internal fault detection is handled inside the fuel pump control module. No external circuits are involved.
Conditions for Running the DTC
The fuel pump control module runs the program to detect an internal fault when power up is commanded. The only requirements are voltage and
ground. This program runs even if the voltage is out of the valid operating range.
Conditions for Setting the DTC
The fuel pump control module has detected an internal malfunction.
Sunday, February 9, 2020
2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1469
2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1469
P161C, or P2610 should not set.
2. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the
conditions that you observed from the Freeze Frame/Failure Records data.
Circuit/System Testing
1. Ignition ON, clear the DTC information with a scan tool. Observe the scan tool DTC information.
瀚慖f DTC P0602, P0610, P0614, P0630, P160D, P160E, or P161C failed this ignition, reprogram the K20 ECM. Refer to Control Module
References (See: Testing and Inspection/Programming and Relearning). If the DTC resets, replace the K20 ECM.
2. Observe the DTC information with a scan tool. Verify DTC P0603, P0604, P0605, P0606, P06D1, or P2610 does not set.
瀚慖f a DTC failed this ignition, replace the K20 ECM.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
Control Module References (See: Testing and Inspection/Programming and Relearning) for engine control module replacement, setup, and
programming
P0614
DTC P0602-P0606, P0610, P0614, P0630, P06D1, P160D, P160E, P161C, or P2610 (ECM, LAU/LBW)
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC P0602
- Control Module Not Programmed
DTC P0603
- Control Module Long Term Memory Reset
DTC P0604
- Control Module Random Access Memory Performance
DTC P0605
- Control Module Programming Read Only Memory Performance
DTC P0606
- Control Module Processor Performance
DTC P0610
- Control Module Vehicle Options Incorrect
DTC P0614
- Engine Control Module/Transmission Control Module Programming Not Plausible
DTC P0630
- VIN Not Programmed or Mismatched - Engine Control Module (ECM)
DTC P06D1
- Control Module Ignition Coil System Circuitry Performance
DTC P160D
- Incorrect Engine Calibration Detected
DTC P160E
- Engine Calibration Monitoring Not Programmed
Friday, November 1, 2019
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1821
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1821
1. Observe the DTC information with a scan tool. DTC P0601, P0602, P0603, P0604, P0606, P0607, P060D, P062F, or P2610 should not set.
2. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the
conditions that you observed from the Freeze Frame/Failure Records data.
Circuit/System Testing
1. Observe the DTC information with a scan tool.
锟斤拷If DTC P0602 is set, attempt to program the K20 ECM before replacing the K20 ECM. Refer to Control Module References (See:
Testing and Inspection/Programming and Relearning) for K20 ECM replacement, setup, and programming.
锟斤拷If DTC P0602 resets, replace the K20 ECM.
2. Observe the DTC information with a scan tool. DTC P0601, P0603, P0604, P0605, P0606, P0607, P060D, P062F, or P2610 should not set.
锟斤拷If a DTC failed this ignition, replace the K20 ECM.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, programming and setup
Fuel Pump Control Module
DTC P0601-P0604, P0606, or P062F
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions)provides an overview of each diagnostic category.
DTC Descriptors
DTC P0601
- Control Module Read Only Memory (ROM)
DTC P0602
- Control Module Not Programmed
DTC P0603
- Control Module Long Term Memory Reset
DTC P0604
- Control Module Random Access Memory (RAM)
DTC P0606
- Control Module Internal Performance
DTC P062F
- Control Module Long Term Memory Performance
Circuit/System Description
The internal fault detection is handled inside the fuel pump control module. No external circuits are involved.
Conditions for Running the DTC
The fuel pump control module runs the program to detect an internal fault when power up is commanded. The only requirements are voltage and
ground. This program runs even if the voltage is out of the valid operating range.
Conditions for Setting the DTC
The fuel pump control module has detected an internal malfunction.
1. Observe the DTC information with a scan tool. DTC P0601, P0602, P0603, P0604, P0606, P0607, P060D, P062F, or P2610 should not set.
2. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the
conditions that you observed from the Freeze Frame/Failure Records data.
Circuit/System Testing
1. Observe the DTC information with a scan tool.
锟斤拷If DTC P0602 is set, attempt to program the K20 ECM before replacing the K20 ECM. Refer to Control Module References (See:
Testing and Inspection/Programming and Relearning) for K20 ECM replacement, setup, and programming.
锟斤拷If DTC P0602 resets, replace the K20 ECM.
2. Observe the DTC information with a scan tool. DTC P0601, P0603, P0604, P0605, P0606, P0607, P060D, P062F, or P2610 should not set.
锟斤拷If a DTC failed this ignition, replace the K20 ECM.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, programming and setup
Fuel Pump Control Module
DTC P0601-P0604, P0606, or P062F
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions)provides an overview of each diagnostic category.
DTC Descriptors
DTC P0601
- Control Module Read Only Memory (ROM)
DTC P0602
- Control Module Not Programmed
DTC P0603
- Control Module Long Term Memory Reset
DTC P0604
- Control Module Random Access Memory (RAM)
DTC P0606
- Control Module Internal Performance
DTC P062F
- Control Module Long Term Memory Performance
Circuit/System Description
The internal fault detection is handled inside the fuel pump control module. No external circuits are involved.
Conditions for Running the DTC
The fuel pump control module runs the program to detect an internal fault when power up is commanded. The only requirements are voltage and
ground. This program runs even if the voltage is out of the valid operating range.
Conditions for Setting the DTC
The fuel pump control module has detected an internal malfunction.
Subscribe to:
Posts (Atom)