2010 Cadillac CTS Sedan AWD V6-3.6L Page 1081

2010 Cadillac CTS Sedan AWD V6-3.6L Page 1081

* DTC P0036, P0037, P0038, P0056, P0057, P0058, P0116, P0117, P0118, P0119, or P0128 is not set.

* The engine speed is greater than 240 RPM.

* The ignition voltage is greater than 10 volts.

* The engine coolant temperature is colder than 40掳C (104掳F) at start-up and the engine coolant temperature was warmer than 60掳C (140掳F)

when the ignition was turned OFF last ignition cycle.

* The calculated exhaust temperature at the HO2S 2 is warmer than 700掳C (1,292掳F) and the HO2S 2 is warmed up for greater than 90

seconds.

* The calculated exhaust temperature is colder than 800掳C (1472掳F) 5 seconds after engine start.

* DTCs P0137 and P0157 run continuously once the above conditions are met.

P0138, P0140, P0158, and P0160

* The engine speed is greater than 240 RPM.

* The ignition voltage is greater than 10 volts.

* The HO2S 2 heater duty cycle is stable and the HO2S 2 is warmed up for greater than 90 seconds.

* The calculated exhaust temperature is colder than 800掳C (1472掳F).

* DTCs P0138 and P0158 run continuously once the above conditions are met for greater than 5 seconds.

* DTCs P0140 and P0160 run continuously once the above conditions are met for greater than 60 seconds.

Conditions for Setting the DTC

P0137 or P0157

The ECM detects that a secondary HO2S signal voltage is less than 60 mV for greater than 1 seconds of for a cumulative of 10 seconds.

P0138 or P0158

The ECM detects that the HO2S signal voltage is greater than 1,150 mV for greater than 1 seconds or for a cumulative of 10 seconds.

P0140 or P0160

* The ECM detects that the HO2S 2 signal voltage is between 401-519 mV.

* The ECM detects that the measured internal resistance of the HO2S 2 is greater than 40,000 ohms, when the calculated exhaust temperature

is warmer than 500掳C (932掳F).

* Either condition exists for greater than 1 second or for a cumulative of 10 seconds.

Action Taken when the DTC Sets

DTCs P0137, P0138, P0140, P0157, P0158, and P0160 are Type B DTCs.

Conditions for Clearing the MIL/DTC

DTCs P0137, P0138, P0140, P0157, P0158, and P0160 are Type B DTCs.

Reference Information

Schematic Reference

Engine Controls Schematics (LLT) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics

(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit

Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Wiring Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

1. Engine idling, observe the appropriate scan tool HO2S 2 voltage parameter. The reading should fluctuate above and below the range of

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1854

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1854

* DTCs P0030, P0036, P0068, P0101, P0102, P0103, P0106, P0107, P0108, P0117, P0118, P0120, P0121, P0128, P0130, P0131, P0132,

P0133, P0134, P0135, P0136, P0137, P0138, P0140, P0141, P0201-P0208, P0220, P0300, P0301-P0304, P0442, P0443, P0446, P0449,

P0452, P0453, P0455, P0496, P1106, P1107, P1114, P1115, P1133, P1516, P2101, P2119, P2120, P2125, P2135, P2138, P2176 are not set.

* The engine is in Closed Loop status.

* The engine coolant temperature (ECT) is between -40 and +150掳C (-40 and +302掳F).

* The intake air temperature (IAT) is between -20 and +150掳C (-4 and +302掳F).

* The manifold absolute pressure (MAP) is between 10-255 kPa (1.45-37 psi).

* The vehicle speed is less than 134 km/h (83 mph).

* The engine speed is between 375-7,000 RPM.

* The mass air flow (MAF) is between 1-510 g/s.

* The barometric pressure (BARO) is more than 70 kPa (10.2 psi).

* The fuel level is more than 10 %.

* This diagnostic runs continuously when the above conditions have been met.

Conditions for Setting the DTC

* The average long term FT weighted average value is more or less than a calibrated value.

* The above condition is present for approximately 3 min after the Conditions for Running the DTC have been met.

Action Taken When the DTC Sets

The ECM records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the ECM stores this information in the

Failure Records. If the diagnostic reports a failure on the second ignition cycle the ECM records the operating conditions at the time of the failure.

The ECM writes the operating conditions to the Freeze Frame and updates the Failure Records. The ECM illuminates the malfunction indicator

lamp (MIL) when one of the following occur:

* The ECM detects the same fuel trim failure during 2 consecutive trips.

* The ECM detects any fuel trim failure during any subsequent trip if the conditions at the time of failure meet the following criteria:

- The engine load is within 20 % of the previous test that failed.

- The engine speed is within 375 RPM of the previous test that failed.

- The engine coolant temperature is in the same range of the previous test that failed.

Conditions for Clearing the MIL/DTC

* The ECM turns OFF the malfunction indicator lamp (MIL) at the beginning of the fourth ignition cycle, after 3 ignition cycles that the

diagnostic runs and does not fail.

* A current DTC, Last Test Failed, clears when the diagnostic runs and passes.

* A history DTC and related Freeze Frame data clears after 40 warm-up cycles, if no failures are reported by this or any other emission related

diagnostic.

* Clear the MIL and the DTC with a scan tool.

Reference Information

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

* Disregard any transmission symptoms, antilock brake system (ABS) indicators, and traction control system (TCS) indicators until any fuel

trim faults are repaired. A fuel trim fault may cause default actions such as harsh shifts and illumination of the ABS/TCS indicators.

* E85 compatible engine only-Over estimation of the ethanol content will result in a rich shift of fuel trim values, and under-estimation will

result in a lean shift of fuel trim values. A fuel trim DTC may set if the learned alcohol content, Fuel Alcohol Content parameter on the scan

tool, is different than the measured alcohol content in the vehicle such that fuel trim values exceed failure threshold values. Refer to Fuel

Composition Diagnosis (See: Powertrain Management/Computers and Control Systems/Testing and Inspection/Component Tests and

General Diagnostics).

* Verify that other DTCs are not set.

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1766

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1766

P0118

The ECM detects that the ECT is colder than -60掳C (-76掳F) for greater than 5 s.

Action Taken When the DTC Sets

DTCs P0117 and P0118 are Type B DTCs.

Conditions for Clearing the MIL/DTC

DTCs P0117 and P0118 are Type B DTCs.

Reference Information

Schematic Reference

Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

Warning

Under pressure, the temperature of the solution in the radiator can be considerably higher, without boiling. Removing the radiator cap while the

engine is hot (pressure is high), will cause the solution to boil instantaneously, with explosive force. The solution will spew out over the engine,

fenders, and the person removing the cap. Serious bodily injury may result. Flammable antifreeze, such as alcohol, is not recommended for use at

any time. Flammable antifreeze could cause a serious fire.

1. Turn OFF the ignition.

2. Inspect the cooling system surge tank for the proper engine coolant level. Refer to Cooling System Leak Testing (See: Engine, Cooling and

Exhaust/Cooling System/Testing and Inspection/Component Tests and General Diagnostics) and Cooling System Draining and Filling (Static

Fill) (See: Engine, Cooling and Exhaust/Cooling System/Service and Repair/Cooling System Draining and Filling (Static Fill)).

3. Turn ON the ignition, with the engine OFF.

4. Use the scan tool to verify the proper operation of the engine cooling system fans.

5. Turn OFF the ignition.

6. Verify the proper heat range, and the operation of the thermostat. Refer to Thermostat Diagnosis (See: Engine, Cooling and

Exhaust/Cooling System/Testing and Inspection/Symptom Related Diagnostic Procedures/Thermostat Diagnosis).

Circuit/System Testing

1. Ignition OFF, disconnect the harness connector at the B34 ECT sensor.

2. Ignition OFF for 90 s, test for less than 5 ohm between the low reference circuit terminal A and ground.

瀚慖f greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the K20

ECM.

3. Ignition ON, verify the scan tool ECT parameter is colder than -39掳C (-38掳F).

瀚慖f greater than the specified range, test the signal circuit terminal B for a short to ground. If the circuit tests normal, replace the K20 ECM.

2010 Cadillac CTS Sedan AWD V6-3.0L Page 1762

2010 Cadillac CTS Sedan AWD V6-3.0L Page 1762

* DTCs P0068, P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120, P0121, P0122, P0123, P0220,

P0222, P0223, P0201, P0202, P0203, P0204, P0205, P0206, P0300, P0335, P0336, P0351, P0352, P0353, P0501, P0502, P0506, P0507,

P0601, P0602, P0603, P0604, P0606, P0607, P060D, P062F, P0641, P0651, P1101, P1516, P1682, P2101, P2119, P2120, P2122, P2123,

P2125, P2127, P2128, P2135, P2138, P2176, P2610 are not set.

This DTC runs for 12 s within the first 17 s of start-up, or until the calculated catalyst temperature is greater than 900掳C (1,652掳F). This diagnostic

runs once per trip when a cold start has been determined.

Conditions for Setting the DTC

The actual exhaust energy model does not match the expected exhaust energy model.

Action Taken When the DTC Sets

DTC P1400 is a Type A DTC.

Conditions for Clearing the MIL/DTC

DTC P1400 is a Type A DTC.

Reference Information

Description and Operation

Engine Control Module Description (See: Powertrain Management/Computers and Control Systems/Description and Operation/Engine Control

Module Description)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Diagnostic Aids

Any loading of the engine that lowers engine RPM, such as with partial application of the clutch, A/C cycling etc., during the first 17 s of engine

run time may set this DTC.

Circuit/System Verification

1. Allow the engine to cool.

2. Start and idle the engine for at least 2 min.

3. DTC P1400 should run and pass.

Circuit/System Testing

* Inspect the air intake system for the following:

- Damage, restriction, or modification

- Dirty or deteriorating air filter element

- Crankcase ventilation system for correct operation-Refer to Crankcase Ventilation System Inspection/Diagnosis (See: Powertrain

Management/Emission Control Systems/Positive Crankcase Ventilation/Testing and Inspection).

- Water intrusion

- Vacuum leak and other un-metered air downstream of the mass air flow (MAF) sensor

- Intake manifold leak

* Inspect the exhaust system for the following:

- Water intrusion

- Exhaust leak

- Damaged, restricted, modified or enhanced exhaust system-Refer to Symptoms - Engine Exhaust (See: Engine, Cooling and

Exhaust/Exhaust System/Testing and Inspection/Symptoms - Engine Exhaust).

* Inspect the engine mechanical for items that could alter the air flow into the combustion chamber. Refer to Symptoms - Engine Mechanical (

See: Engine, Cooling and Exhaust/Engine/Testing and Inspection/Symptom Related Diagnostic Procedures/Symptoms - Engine Mechanical).

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

2010 Cadillac Truck Escalade RWD V8-6.2L Page 1854

2010 Cadillac Truck Escalade RWD V8-6.2L Page 1854

* DTCs P0030, P0036, P0068, P0101, P0102, P0103, P0106, P0107, P0108, P0117, P0118, P0120, P0121, P0128, P0130, P0131, P0132,

P0133, P0134, P0135, P0136, P0137, P0138, P0140, P0141, P0201-P0208, P0220, P0300, P0301-P0304, P0442, P0443, P0446, P0449,

P0452, P0453, P0455, P0496, P1106, P1107, P1114, P1115, P1133, P1516, P2101, P2119, P2120, P2125, P2135, P2138, P2176 are not set.

* The engine is in Closed Loop status.

* The engine coolant temperature (ECT) is between -40 and +150掳C (-40 and +302掳F).

* The intake air temperature (IAT) is between -20 and +150掳C (-4 and +302掳F).

* The manifold absolute pressure (MAP) is between 10-255 kPa (1.45-37 psi).

* The vehicle speed is less than 134 km/h (83 mph).

* The engine speed is between 375-7,000 RPM.

* The mass air flow (MAF) is between 1-510 g/s.

* The barometric pressure (BARO) is more than 70 kPa (10.2 psi).

* The fuel level is more than 10 %.

* This diagnostic runs continuously when the above conditions have been met.

Conditions for Setting the DTC

* The average long term FT weighted average value is more or less than a calibrated value.

* The above condition is present for approximately 3 min after the Conditions for Running the DTC have been met.

Action Taken When the DTC Sets

The ECM records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the ECM stores this information in the

Failure Records. If the diagnostic reports a failure on the second ignition cycle the ECM records the operating conditions at the time of the failure.

The ECM writes the operating conditions to the Freeze Frame and updates the Failure Records. The ECM illuminates the malfunction indicator

lamp (MIL) when one of the following occur:

* The ECM detects the same fuel trim failure during 2 consecutive trips.

* The ECM detects any fuel trim failure during any subsequent trip if the conditions at the time of failure meet the following criteria:

- The engine load is within 20 % of the previous test that failed.

- The engine speed is within 375 RPM of the previous test that failed.

- The engine coolant temperature is in the same range of the previous test that failed.

Conditions for Clearing the MIL/DTC

* The ECM turns OFF the malfunction indicator lamp (MIL) at the beginning of the fourth ignition cycle, after 3 ignition cycles that the

diagnostic runs and does not fail.

* A current DTC, Last Test Failed, clears when the diagnostic runs and passes.

* A history DTC and related Freeze Frame data clears after 40 warm-up cycles, if no failures are reported by this or any other emission related

diagnostic.

* Clear the MIL and the DTC with a scan tool.

Reference Information

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

* Disregard any transmission symptoms, antilock brake system (ABS) indicators, and traction control system (TCS) indicators until any fuel

trim faults are repaired. A fuel trim fault may cause default actions such as harsh shifts and illumination of the ABS/TCS indicators.

* E85 compatible engine only-Over estimation of the ethanol content will result in a rich shift of fuel trim values, and under-estimation will

result in a lean shift of fuel trim values. A fuel trim DTC may set if the learned alcohol content, Fuel Alcohol Content parameter on the scan

tool, is different than the measured alcohol content in the vehicle such that fuel trim values exceed failure threshold values. Refer to Fuel

Composition Diagnosis (See: Powertrain Management/Computers and Control Systems/Testing and Inspection/Component Tests and

General Diagnostics).

* Verify that other DTCs are not set.

2010 Cadillac Truck Escalade RWD V8-6.2L Page 1766

2010 Cadillac Truck Escalade RWD V8-6.2L Page 1766

P0118

The ECM detects that the ECT is colder than -60掳C (-76掳F) for greater than 5 s.

Action Taken When the DTC Sets

DTCs P0117 and P0118 are Type B DTCs.

Conditions for Clearing the MIL/DTC

DTCs P0117 and P0118 are Type B DTCs.

Reference Information

Schematic Reference

Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

Warning

Under pressure, the temperature of the solution in the radiator can be considerably higher, without boiling. Removing the radiator cap while the

engine is hot (pressure is high), will cause the solution to boil instantaneously, with explosive force. The solution will spew out over the engine,

fenders, and the person removing the cap. Serious bodily injury may result. Flammable antifreeze, such as alcohol, is not recommended for use at

any time. Flammable antifreeze could cause a serious fire.

1. Turn OFF the ignition.

2. Inspect the cooling system surge tank for the proper engine coolant level. Refer to Cooling System Leak Testing (See: Engine, Cooling and

Exhaust/Cooling System/Testing and Inspection/Component Tests and General Diagnostics) and Cooling System Draining and Filling (Static

Fill) (See: Engine, Cooling and Exhaust/Cooling System/Service and Repair/Cooling System Draining and Filling (Static Fill)).

3. Turn ON the ignition, with the engine OFF.

4. Use the scan tool to verify the proper operation of the engine cooling system fans.

5. Turn OFF the ignition.

6. Verify the proper heat range, and the operation of the thermostat. Refer to Thermostat Diagnosis (See: Engine, Cooling and

Exhaust/Cooling System/Testing and Inspection/Symptom Related Diagnostic Procedures/Thermostat Diagnosis).

Circuit/System Testing

1. Ignition OFF, disconnect the harness connector at the B34 ECT sensor.

2. Ignition OFF for 90 s, test for less than 5 ohm between the low reference circuit terminal A and ground.

瀚慖f greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the K20

ECM.

3. Ignition ON, verify the scan tool ECT parameter is colder than -39掳C (-38掳F).

瀚慖f greater than the specified range, test the signal circuit terminal B for a short to ground. If the circuit tests normal, replace the K20 ECM.

2010 Cadillac CTS Sedan AWD V6-3.6L Page 1786

2010 Cadillac CTS Sedan AWD V6-3.6L Page 1786

* DTCs P0068, P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120, P0121, P0122, P0123, P0220,

P0222, P0223, P0201, P0202, P0203, P0204, P0205, P0206, P0300, P0335, P0336, P0351, P0352, P0353, P0501, P0502, P0506, P0507,

P0601, P0602, P0603, P0604, P0606, P0607, P060D, P062F, P0641, P0651, P1101, P1516, P1682, P2101, P2119, P2120, P2122, P2123,

P2125, P2127, P2128, P2135, P2138, P2176, P2610 are not set.

This DTC runs for 12 s within the first 17 s of start-up, or until the calculated catalyst temperature is greater than 900掳C (1,652掳F). This diagnostic

runs once per trip when a cold start has been determined.

Conditions for Setting the DTC

The actual exhaust energy model does not match the expected exhaust energy model.

Action Taken When the DTC Sets

DTC P1400 is a Type A DTC.

Conditions for Clearing the MIL/DTC

DTC P1400 is a Type A DTC.

Reference Information

Description and Operation

Engine Control Module Description (See: Powertrain Management/Computers and Control Systems/Description and Operation/Engine Control

Module Description)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Diagnostic Aids

Any loading of the engine that lowers engine RPM, such as with partial application of the clutch, A/C cycling etc., during the first 17 s of engine

run time may set this DTC.

Circuit/System Verification

1. Allow the engine to cool.

2. Start and idle the engine for at least 2 min.

3. DTC P1400 should run and pass.

Circuit/System Testing

* Inspect the air intake system for the following:

- Damage, restriction, or modification

- Dirty or deteriorating air filter element

- Crankcase ventilation system for correct operation-Refer to Crankcase Ventilation System Inspection/Diagnosis (See: Powertrain

Management/Emission Control Systems/Positive Crankcase Ventilation/Testing and Inspection).

- Water intrusion

- Vacuum leak and other un-metered air downstream of the mass air flow (MAF) sensor

- Intake manifold leak

* Inspect the exhaust system for the following:

- Water intrusion

- Exhaust leak

- Damaged, restricted, modified or enhanced exhaust system-Refer to Symptoms - Engine Exhaust (See: Engine, Cooling and

Exhaust/Exhaust System/Testing and Inspection/Symptoms - Engine Exhaust).

* Inspect the engine mechanical for items that could alter the air flow into the combustion chamber. Refer to Symptoms - Engine Mechanical (

See: Engine, Cooling and Exhaust/Engine/Testing and Inspection/Symptom Related Diagnostic Procedures/Symptoms - Engine Mechanical).

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1340

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1340

* DTC P0100, P0101, P0102, P0103, P0111, P0112, P0113, P0114, P0116, P0117, P0118, P0119, P0418, P050C, P2227, P2228, P2229,

P2257, or P2258 is not set.

* Greater than 60 min has elapsed since the last cold start.

* The secondary air injection system has been commanded ON and OFF during the ignition cycle.

* The battery voltage is between 10-18 V.

* The engine speed is between 680-3,500 RPM.

* The Intake Air Temperature (IAT) is between -12 to +80掳C (10.4-176掳F).

* The Engine Coolant Temperature (ECT) is between -10.5 to +69.8掳C (13-158掳F).

* The Mass Air Flow (MAF) is less than 100 g/s.

* Catalyst heating is active.

* The Barometric Pressure (BARO) is less than 68 kPa (9.9 psi).

* The difference between intake air temp and engine coolant start temp is less than 15掳C (27掳F).

* DTC P0411 runs once per ignition cycle when the above conditions are met.

Conditions for Setting the DTC

* The ratio of the calculated secondary air mass flow to the modeled secondary air mass flow is less than 0.75 or greater than 1.2.

* DTC P0411 sets within 60 s when the above condition is met.

Action Taken When the DTC Sets

DTC P0411 is a Type B DTC.

Conditions for Clearing the DTC

DTC P0411 is a Type B DTC.

Reference Information

Schematic Reference

Engine Controls Schematics (LAU) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics

(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)

Description and Operation

Secondary Air Injection System Description (See: Powertrain Management/Emission Control Systems/Air Injection/Description and Operation)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

Note: Do not run secondary air injection pump for more than 1-2 minutes at a time. Running for an extended period of time without allowing

pump to cool may cause damage to the pump.

1. Ignition ON, observe the DTC information with a scan tool. Verify that DTC P2431, P2432, or P2433 is not set.

瀚慖f a DTC is set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code Descriptions/Diagnostic Trouble

Code (DTC) List - Vehicle) for further diagnosis.

2. Observe the scan tool Secondary Air Injection Pressure Sensor voltage parameter. The reading should be between 1.0-4.0 V.

3. Compare the scan tool BARO pressure parameter to the Altitude Versus Barometric Pressure (See: Powertrain Management/Computers and

2010 Cadillac CTS Sedan AWD V6-3.6L Page 1867

2010 Cadillac CTS Sedan AWD V6-3.6L Page 1867

* DTCs P0102, P0103, P0107, P0108, P0112, P0113, P0117, P0118, P0335, or P0336 is not set.

* The engine speed is between 400-7,000 RPM.

* The engine coolant temperature (ECT) is between 69-127掳C (156-260掳F).

* The intake air temperature (IAT) is between -20 to +125掳C (-4 to +257掳F).

* The DTC runs continuously when the above conditions are met.

P0122, P0123, P0222, P0223

* DTC P06A3 is not set.

* The ignition is ON, or the engine is running.

* The engine is not operating in reduced power mode.

* The ignition voltage is greater than 6 V.

* The DTCs runs continuously when the above condition are met.

P2135

* DTCs P0121, P0122, P0123, P0222, P0223, or P06A3 are not set.

* The ignition is ON, or the engine is running.

* The engine is not operating in reduced power mode.

* The ignition voltage is greater than 6 V.

* The DTCs runs continuously when the above conditions are met.

Conditions for Setting the DTC

P0121

The ECM detects that the TP sensor 1 voltage is stuck in range for less than 1 s.

P0122

The ECM detects that the TP sensor 1 voltage is less than 0.3 V for less than 1 s.

P0123

The ECM detects that the TP sensor 1 voltage is greater than 4.8 V for less than 1 s.

P0222

The ECM detects that the TP sensor 2 voltage is less than 0.3 V for less than 1 s.

P0223

The ECM detects that the TP sensor 2 voltage is greater than 4.6 V for less than 1 s.

P2135

The ECM detects that TP sensor 1 and TP sensor 2 disagree greater than 7-10 percent for less than 1 s.

Action Taken When the DTC Sets

P0121

* DTC P0121 is a type B DTC.

* The ECM commands the throttle actuator control (TAC) system to operate in a Reduced Engine Power mode.

P0122, P0123, P0222, P0223, or P2135

* DTC P0122, P0123, P0222, P0223, and P2135 are type A DTCs.

* The ECM commands the throttle actuator control (TAC) system to operate in a Reduced Engine Power mode.

Conditions for Clearing the DTC

* DTC P0121 is a type B DTC.

* DTCs P0122, P0123, P0222, P0223 and P2135 is a type A DTC.

Diagnostic Aids

* If the Throttle Sweep Test is not available on the scan tool, observe the scan tool TP Sensor 1 and 2 Agree/Disagree parameter while

performing the following tests:

- Slowly depress the accelerator pedal to WOT and then slowly return the pedal to closed throttle. Repeat the procedure several times.

- Rapidly depress the accelerator pedal from the rest position to the wide open throttle position (WOT) and release pedal. Repeat the

procedure several times.

The TP Sensor 1 and 2 Agree/Disagree parameter should display Agree. If Disagree is displayed, continue diagnosis in Circuit/System

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1934

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1934

* DTC P0111, P0112, P0113, P0116, P0117, P0118, P0119, P2600, P2602, or P2603 is not set.

* The ignition is OFF.

* The engine coolant temperature (ECT) at engine shut down is warmer than 110 掳C (230 掳F).

* The auxiliary coolant pump is enabled.

* The DTC runs continuously once the conditions above are met for greater than 30 S.

Conditions for Setting the DTC

P2600

The ECM detects the pump control circuit is open. The condition exists for 4 S or a cumulative of 30 S.

P2601

The ECM detects that the ECT decreases less than 2 掳C (4 掳F) within 60 seconds. The condition exists for 4 S or a cumulative of 30 S.

P2602

The ECM detects the pump control circuit is shorted to ground. The condition exists for 4 seconds or a cumulative of 30 seconds.

P2603

The ECM detects the pump control circuit is shorted to voltage. The condition exists for 4 seconds or a cumulative of 30 seconds.

Action Taken When the DTC Sets

The DTCs are Type C DTCs.

Conditions for Clearing the DTC

The DTCs are Type C DTCs.

Diagnostic Aids

* This diagnostic uses a comprehensive approach to the diagnosis of the KR31 auxiliary coolant pump relay and its related circuits. The

auxiliary coolant pump relay is a printed circuit board (PCB) relay. The relay is an integral component to the underhood bussed electrical

center (UBEC). It cannot be removed and it is not visible.

* Much of the diagnosis is performed at the ECM connectors. Great care should be taken to ensure that the correct terminals are tested and the

proper test probes are utilized when performing this diagnostic.

* The test lamp is used to provide a visual aid to observe the integrity of the KR31 relay, the UBEC and the relay control circuit.

* Grounding terminal X2-58 activates the powertrain relay, which will supply power through KR31 relay coil and the relay control circuit.

Under normal circumstances the test lamp will illuminate with dim intensity due to the load created by the KR31 relay coil. If the test lamp

does not illuminate, or illuminates brightly a condition exists in the KR31 relay control circuit or the UBEC.

Reference Information

Schematic Reference

* Engine Cooling Schematics (See: Engine, Cooling and Exhaust/Cooling System/Diagrams)

* Engine Controls Schematics (LAU) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls

Schematics (LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1955

2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1955

* DTCs P0030, P0036, P0068, P0101, P0102, P0103, P0106, P0107, P0108, P0117, P0118, P0120, P0121, P0128, P0130, P0131, P0132,

P0133, P0134, P0135, P0136, P0137, P0138, P0140, P0141, P0201-P0208, P0220, P0300, P0301-P0304, P0442, P0443, P0446, P0449,

P0452, P0453, P0455, P0496, P1106, P1107, P1114, P1115, P1133, P1516, P2101, P2119, P2120, P2125, P2135, P2138, P2176 are not set.

* The engine is in Closed Loop status.

* The engine coolant temperature (ECT) is between -40 and +150锟斤拷C (-40 and +302锟斤拷F).

* The intake air temperature (IAT) is between -20 and +150锟斤拷C (-4 and +302锟斤拷F).

* The manifold absolute pressure (MAP) is between 10-255 kPa (1.45-37 psi).

* The vehicle speed is less than 134 km/h (83 mph).

* The engine speed is between 375-7,000 RPM.

* The mass air flow (MAF) is between 1-510 g/s.

* The barometric pressure (BARO) is more than 70 kPa (10.2 psi).

* The fuel level is more than 10 %.

* This diagnostic runs continuously when the above conditions have been met.

Conditions for Setting the DTC

* The average long term FT weighted average value is more or less than a calibrated value.

* The above condition is present for approximately 3 min after the Conditions for Running the DTC have been met.

Action Taken When the DTC Sets

The ECM records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the ECM stores this information in the

Failure Records. If the diagnostic reports a failure on the second ignition cycle the ECM records the operating conditions at the time of the failure.

The ECM writes the operating conditions to the Freeze Frame and updates the Failure Records. The ECM illuminates the malfunction indicator

lamp (MIL) when one of the following occur:

* The ECM detects the same fuel trim failure during 2 consecutive trips.

* The ECM detects any fuel trim failure during any subsequent trip if the conditions at the time of failure meet the following criteria:

- The engine load is within 20 % of the previous test that failed.

- The engine speed is within 375 RPM of the previous test that failed.

- The engine coolant temperature is in the same range of the previous test that failed.

Conditions for Clearing the MIL/DTC

* The ECM turns OFF the malfunction indicator lamp (MIL) at the beginning of the fourth ignition cycle, after 3 ignition cycles that the

diagnostic runs and does not fail.

* A current DTC, Last Test Failed, clears when the diagnostic runs and passes.

* A history DTC and related Freeze Frame data clears after 40 warm-up cycles, if no failures are reported by this or any other emission related

diagnostic.

* Clear the MIL and the DTC with a scan tool.

Reference Information

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

* Disregard any transmission symptoms, antilock brake system (ABS) indicators, and traction control system (TCS) indicators until any fuel

trim faults are repaired. A fuel trim fault may cause default actions such as harsh shifts and illumination of the ABS/TCS indicators.

* E85 compatible engine only-Over estimation of the ethanol content will result in a rich shift of fuel trim values, and under-estimation will

result in a lean shift of fuel trim values. A fuel trim DTC may set if the learned alcohol content, Fuel Alcohol Content parameter on the scan

tool, is different than the measured alcohol content in the vehicle such that fuel trim values exceed failure threshold values. Refer to Fuel

Composition Diagnosis (See: Powertrain Management/Computers and Control Systems/Testing and Inspection/Component Tests and

General Diagnostics).

* Verify that other DTCs are not set.

2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1867

2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1867

P0118

The ECM detects that the ECT is colder than -60锟斤拷C (-76锟斤拷F) for greater than 5 s.

Action Taken When the DTC Sets

DTCs P0117 and P0118 are Type B DTCs.

Conditions for Clearing the MIL/DTC

DTCs P0117 and P0118 are Type B DTCs.

Reference Information

Schematic Reference

Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

Warning

Under pressure, the temperature of the solution in the radiator can be considerably higher, without boiling. Removing the radiator cap while the

engine is hot (pressure is high), will cause the solution to boil instantaneously, with explosive force. The solution will spew out over the engine,

fenders, and the person removing the cap. Serious bodily injury may result. Flammable antifreeze, such as alcohol, is not recommended for use at

any time. Flammable antifreeze could cause a serious fire.

1. Turn OFF the ignition.

2. Inspect the cooling system surge tank for the proper engine coolant level. Refer to Cooling System Leak Testing (See: Engine, Cooling and

Exhaust/Cooling System/Testing and Inspection/Component Tests and General Diagnostics) and Cooling System Draining and Filling (Static

Fill) (See: Engine, Cooling and Exhaust/Cooling System/Service and Repair/Cooling System Draining and Filling (Static Fill)).

3. Turn ON the ignition, with the engine OFF.

4. Use the scan tool to verify the proper operation of the engine cooling system fans.

5. Turn OFF the ignition.

6. Verify the proper heat range, and the operation of the thermostat. Refer to Thermostat Diagnosis (See: Engine, Cooling and

Exhaust/Cooling System/Testing and Inspection/Symptom Related Diagnostic Procedures/Thermostat Diagnosis).

Circuit/System Testing

1. Ignition OFF, disconnect the harness connector at the B34 ECT sensor.

2. Ignition OFF for 90 s, test for less than 5 ohm between the low reference circuit terminal A and ground.

锟斤拷If greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the K20

ECM.

3. Ignition ON, verify the scan tool ECT parameter is colder than -39锟斤拷C (-38锟斤拷F).

锟斤拷If greater than the specified range, test the signal circuit terminal B for a short to ground. If the circuit tests normal, replace the K20 ECM.