2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1854
* DTCs P0030, P0036, P0068, P0101, P0102, P0103, P0106, P0107, P0108, P0117, P0118, P0120, P0121, P0128, P0130, P0131, P0132,
P0133, P0134, P0135, P0136, P0137, P0138, P0140, P0141, P0201-P0208, P0220, P0300, P0301-P0304, P0442, P0443, P0446, P0449,
P0452, P0453, P0455, P0496, P1106, P1107, P1114, P1115, P1133, P1516, P2101, P2119, P2120, P2125, P2135, P2138, P2176 are not set.
* The engine is in Closed Loop status.
* The engine coolant temperature (ECT) is between -40 and +150掳C (-40 and +302掳F).
* The intake air temperature (IAT) is between -20 and +150掳C (-4 and +302掳F).
* The manifold absolute pressure (MAP) is between 10-255 kPa (1.45-37 psi).
* The vehicle speed is less than 134 km/h (83 mph).
* The engine speed is between 375-7,000 RPM.
* The mass air flow (MAF) is between 1-510 g/s.
* The barometric pressure (BARO) is more than 70 kPa (10.2 psi).
* The fuel level is more than 10 %.
* This diagnostic runs continuously when the above conditions have been met.
Conditions for Setting the DTC
* The average long term FT weighted average value is more or less than a calibrated value.
* The above condition is present for approximately 3 min after the Conditions for Running the DTC have been met.
Action Taken When the DTC Sets
The ECM records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the ECM stores this information in the
Failure Records. If the diagnostic reports a failure on the second ignition cycle the ECM records the operating conditions at the time of the failure.
The ECM writes the operating conditions to the Freeze Frame and updates the Failure Records. The ECM illuminates the malfunction indicator
lamp (MIL) when one of the following occur:
* The ECM detects the same fuel trim failure during 2 consecutive trips.
* The ECM detects any fuel trim failure during any subsequent trip if the conditions at the time of failure meet the following criteria:
- The engine load is within 20 % of the previous test that failed.
- The engine speed is within 375 RPM of the previous test that failed.
- The engine coolant temperature is in the same range of the previous test that failed.
Conditions for Clearing the MIL/DTC
* The ECM turns OFF the malfunction indicator lamp (MIL) at the beginning of the fourth ignition cycle, after 3 ignition cycles that the
diagnostic runs and does not fail.
* A current DTC, Last Test Failed, clears when the diagnostic runs and passes.
* A history DTC and related Freeze Frame data clears after 40 warm-up cycles, if no failures are reported by this or any other emission related
diagnostic.
* Clear the MIL and the DTC with a scan tool.
Reference Information
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Verification
* Disregard any transmission symptoms, antilock brake system (ABS) indicators, and traction control system (TCS) indicators until any fuel
trim faults are repaired. A fuel trim fault may cause default actions such as harsh shifts and illumination of the ABS/TCS indicators.
* E85 compatible engine only-Over estimation of the ethanol content will result in a rich shift of fuel trim values, and under-estimation will
result in a lean shift of fuel trim values. A fuel trim DTC may set if the learned alcohol content, Fuel Alcohol Content parameter on the scan
tool, is different than the measured alcohol content in the vehicle such that fuel trim values exceed failure threshold values. Refer to Fuel
Composition Diagnosis (See: Powertrain Management/Computers and Control Systems/Testing and Inspection/Component Tests and
General Diagnostics).
* Verify that other DTCs are not set.
Showing posts with label P0121. Show all posts
Showing posts with label P0121. Show all posts
Wednesday, November 4, 2020
Wednesday, August 19, 2020
2010 Cadillac CTS Sedan AWD V6-3.0L Page 1762
2010 Cadillac CTS Sedan AWD V6-3.0L Page 1762
* DTCs P0068, P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120, P0121, P0122, P0123, P0220,
P0222, P0223, P0201, P0202, P0203, P0204, P0205, P0206, P0300, P0335, P0336, P0351, P0352, P0353, P0501, P0502, P0506, P0507,
P0601, P0602, P0603, P0604, P0606, P0607, P060D, P062F, P0641, P0651, P1101, P1516, P1682, P2101, P2119, P2120, P2122, P2123,
P2125, P2127, P2128, P2135, P2138, P2176, P2610 are not set.
This DTC runs for 12 s within the first 17 s of start-up, or until the calculated catalyst temperature is greater than 900掳C (1,652掳F). This diagnostic
runs once per trip when a cold start has been determined.
Conditions for Setting the DTC
The actual exhaust energy model does not match the expected exhaust energy model.
Action Taken When the DTC Sets
DTC P1400 is a Type A DTC.
Conditions for Clearing the MIL/DTC
DTC P1400 is a Type A DTC.
Reference Information
Description and Operation
Engine Control Module Description (See: Powertrain Management/Computers and Control Systems/Description and Operation/Engine Control
Module Description)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Diagnostic Aids
Any loading of the engine that lowers engine RPM, such as with partial application of the clutch, A/C cycling etc., during the first 17 s of engine
run time may set this DTC.
Circuit/System Verification
1. Allow the engine to cool.
2. Start and idle the engine for at least 2 min.
3. DTC P1400 should run and pass.
Circuit/System Testing
* Inspect the air intake system for the following:
- Damage, restriction, or modification
- Dirty or deteriorating air filter element
- Crankcase ventilation system for correct operation-Refer to Crankcase Ventilation System Inspection/Diagnosis (See: Powertrain
Management/Emission Control Systems/Positive Crankcase Ventilation/Testing and Inspection).
- Water intrusion
- Vacuum leak and other un-metered air downstream of the mass air flow (MAF) sensor
- Intake manifold leak
* Inspect the exhaust system for the following:
- Water intrusion
- Exhaust leak
- Damaged, restricted, modified or enhanced exhaust system-Refer to Symptoms - Engine Exhaust (See: Engine, Cooling and
Exhaust/Exhaust System/Testing and Inspection/Symptoms - Engine Exhaust).
* Inspect the engine mechanical for items that could alter the air flow into the combustion chamber. Refer to Symptoms - Engine Mechanical (
See: Engine, Cooling and Exhaust/Engine/Testing and Inspection/Symptom Related Diagnostic Procedures/Symptoms - Engine Mechanical).
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
Wednesday, June 24, 2020
2010 Cadillac Truck Escalade RWD V8-6.2L Page 1854
2010 Cadillac Truck Escalade RWD V8-6.2L Page 1854
* DTCs P0030, P0036, P0068, P0101, P0102, P0103, P0106, P0107, P0108, P0117, P0118, P0120, P0121, P0128, P0130, P0131, P0132,
P0133, P0134, P0135, P0136, P0137, P0138, P0140, P0141, P0201-P0208, P0220, P0300, P0301-P0304, P0442, P0443, P0446, P0449,
P0452, P0453, P0455, P0496, P1106, P1107, P1114, P1115, P1133, P1516, P2101, P2119, P2120, P2125, P2135, P2138, P2176 are not set.
* The engine is in Closed Loop status.
* The engine coolant temperature (ECT) is between -40 and +150掳C (-40 and +302掳F).
* The intake air temperature (IAT) is between -20 and +150掳C (-4 and +302掳F).
* The manifold absolute pressure (MAP) is between 10-255 kPa (1.45-37 psi).
* The vehicle speed is less than 134 km/h (83 mph).
* The engine speed is between 375-7,000 RPM.
* The mass air flow (MAF) is between 1-510 g/s.
* The barometric pressure (BARO) is more than 70 kPa (10.2 psi).
* The fuel level is more than 10 %.
* This diagnostic runs continuously when the above conditions have been met.
Conditions for Setting the DTC
* The average long term FT weighted average value is more or less than a calibrated value.
* The above condition is present for approximately 3 min after the Conditions for Running the DTC have been met.
Action Taken When the DTC Sets
The ECM records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the ECM stores this information in the
Failure Records. If the diagnostic reports a failure on the second ignition cycle the ECM records the operating conditions at the time of the failure.
The ECM writes the operating conditions to the Freeze Frame and updates the Failure Records. The ECM illuminates the malfunction indicator
lamp (MIL) when one of the following occur:
* The ECM detects the same fuel trim failure during 2 consecutive trips.
* The ECM detects any fuel trim failure during any subsequent trip if the conditions at the time of failure meet the following criteria:
- The engine load is within 20 % of the previous test that failed.
- The engine speed is within 375 RPM of the previous test that failed.
- The engine coolant temperature is in the same range of the previous test that failed.
Conditions for Clearing the MIL/DTC
* The ECM turns OFF the malfunction indicator lamp (MIL) at the beginning of the fourth ignition cycle, after 3 ignition cycles that the
diagnostic runs and does not fail.
* A current DTC, Last Test Failed, clears when the diagnostic runs and passes.
* A history DTC and related Freeze Frame data clears after 40 warm-up cycles, if no failures are reported by this or any other emission related
diagnostic.
* Clear the MIL and the DTC with a scan tool.
Reference Information
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Verification
* Disregard any transmission symptoms, antilock brake system (ABS) indicators, and traction control system (TCS) indicators until any fuel
trim faults are repaired. A fuel trim fault may cause default actions such as harsh shifts and illumination of the ABS/TCS indicators.
* E85 compatible engine only-Over estimation of the ethanol content will result in a rich shift of fuel trim values, and under-estimation will
result in a lean shift of fuel trim values. A fuel trim DTC may set if the learned alcohol content, Fuel Alcohol Content parameter on the scan
tool, is different than the measured alcohol content in the vehicle such that fuel trim values exceed failure threshold values. Refer to Fuel
Composition Diagnosis (See: Powertrain Management/Computers and Control Systems/Testing and Inspection/Component Tests and
General Diagnostics).
* Verify that other DTCs are not set.
* DTCs P0030, P0036, P0068, P0101, P0102, P0103, P0106, P0107, P0108, P0117, P0118, P0120, P0121, P0128, P0130, P0131, P0132,
P0133, P0134, P0135, P0136, P0137, P0138, P0140, P0141, P0201-P0208, P0220, P0300, P0301-P0304, P0442, P0443, P0446, P0449,
P0452, P0453, P0455, P0496, P1106, P1107, P1114, P1115, P1133, P1516, P2101, P2119, P2120, P2125, P2135, P2138, P2176 are not set.
* The engine is in Closed Loop status.
* The engine coolant temperature (ECT) is between -40 and +150掳C (-40 and +302掳F).
* The intake air temperature (IAT) is between -20 and +150掳C (-4 and +302掳F).
* The manifold absolute pressure (MAP) is between 10-255 kPa (1.45-37 psi).
* The vehicle speed is less than 134 km/h (83 mph).
* The engine speed is between 375-7,000 RPM.
* The mass air flow (MAF) is between 1-510 g/s.
* The barometric pressure (BARO) is more than 70 kPa (10.2 psi).
* The fuel level is more than 10 %.
* This diagnostic runs continuously when the above conditions have been met.
Conditions for Setting the DTC
* The average long term FT weighted average value is more or less than a calibrated value.
* The above condition is present for approximately 3 min after the Conditions for Running the DTC have been met.
Action Taken When the DTC Sets
The ECM records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the ECM stores this information in the
Failure Records. If the diagnostic reports a failure on the second ignition cycle the ECM records the operating conditions at the time of the failure.
The ECM writes the operating conditions to the Freeze Frame and updates the Failure Records. The ECM illuminates the malfunction indicator
lamp (MIL) when one of the following occur:
* The ECM detects the same fuel trim failure during 2 consecutive trips.
* The ECM detects any fuel trim failure during any subsequent trip if the conditions at the time of failure meet the following criteria:
- The engine load is within 20 % of the previous test that failed.
- The engine speed is within 375 RPM of the previous test that failed.
- The engine coolant temperature is in the same range of the previous test that failed.
Conditions for Clearing the MIL/DTC
* The ECM turns OFF the malfunction indicator lamp (MIL) at the beginning of the fourth ignition cycle, after 3 ignition cycles that the
diagnostic runs and does not fail.
* A current DTC, Last Test Failed, clears when the diagnostic runs and passes.
* A history DTC and related Freeze Frame data clears after 40 warm-up cycles, if no failures are reported by this or any other emission related
diagnostic.
* Clear the MIL and the DTC with a scan tool.
Reference Information
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Verification
* Disregard any transmission symptoms, antilock brake system (ABS) indicators, and traction control system (TCS) indicators until any fuel
trim faults are repaired. A fuel trim fault may cause default actions such as harsh shifts and illumination of the ABS/TCS indicators.
* E85 compatible engine only-Over estimation of the ethanol content will result in a rich shift of fuel trim values, and under-estimation will
result in a lean shift of fuel trim values. A fuel trim DTC may set if the learned alcohol content, Fuel Alcohol Content parameter on the scan
tool, is different than the measured alcohol content in the vehicle such that fuel trim values exceed failure threshold values. Refer to Fuel
Composition Diagnosis (See: Powertrain Management/Computers and Control Systems/Testing and Inspection/Component Tests and
General Diagnostics).
* Verify that other DTCs are not set.
Monday, May 4, 2020
2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1859
2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1859
* Before the ECM can report DTC P2227 failed, DTCs P0100, P0101, P0102, P0103, P0111, P0112, P0113, P0114, P0121, P0122, P0123,
P0221, P0222, P0223, P0236, P0237, P0238, P2228, and P2229 must run and pass.
* The engine is operating.
* The engine speed is less than 1,120 RPM.
* The throttle position sensor parameter is less than 10 %.
* DTC P2227 runs whenever the above conditions are met.
P2228 or P2229
* The ignition is ON.
* The DTCs run continuously when the above condition is met for 0.2 s.
Conditions for Setting the DTC
P2227
* The ECM detects that the BARO sensor signal plus a calibrated threshold is less than the boost pressure sensor signal plus a calibrated
threshold for more than 9 s.
OR
* The ECM detects that the BARO sensor signal plus a calibrated threshold greater than the boost pressure sensor signal plus a calibrated
threshold for more than 9 s.
OR
* The ECM detects that the BARO pressure changed greater than 5 kPa (0.7 psi) within 20 s.
OR
* The ECM detects that the BARO pressure changed greater than 10 kPa (1.5 psi) since the last ignition cycle.
P2228
* The ECM detects that the BARO sensor voltage is less than 0.20 V for 0.5 s.
OR
* The ECM detects that the BARO sensor signal is less than 45 kPa (6.5 psi) for 2 s
P2229
* The ECM detects that the BARO sensor voltage is greater than 4.8 V for 0.5 s.
OR
* The ECM detects that the BARO sensor signal is greater than 115 kPa (16.7 psi) for 2 s.
Action Taken When the DTC Sets
DTCs P2227, P2228, and P2229 are Type B DTCs.
Conditions for Clearing the MIL/DTC
DTCs P2227, P2228, and P2229 are Type B DTCs.
Reference Information
Schematic Reference
Engine Controls Schematics (LAU) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics
(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Verification
1. Start the engine. Observe the DTC information with a scan tool. DTCs P2227, P2228, or P2229 should not set.
2. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the
conditions that you observed from the Freeze Frame/Failure Records data.
Circuit/System Testing
1. Inspect the atmospheric vent on the K20 ECM case for one of the following conditions:
* Moisture in the vent inlet
* Debris in the vent inlet
Thursday, April 2, 2020
2010 Cadillac CTS Sedan AWD V6-3.6L Page 1786
2010 Cadillac CTS Sedan AWD V6-3.6L Page 1786
* DTCs P0068, P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120, P0121, P0122, P0123, P0220,
P0222, P0223, P0201, P0202, P0203, P0204, P0205, P0206, P0300, P0335, P0336, P0351, P0352, P0353, P0501, P0502, P0506, P0507,
P0601, P0602, P0603, P0604, P0606, P0607, P060D, P062F, P0641, P0651, P1101, P1516, P1682, P2101, P2119, P2120, P2122, P2123,
P2125, P2127, P2128, P2135, P2138, P2176, P2610 are not set.
This DTC runs for 12 s within the first 17 s of start-up, or until the calculated catalyst temperature is greater than 900掳C (1,652掳F). This diagnostic
runs once per trip when a cold start has been determined.
Conditions for Setting the DTC
The actual exhaust energy model does not match the expected exhaust energy model.
Action Taken When the DTC Sets
DTC P1400 is a Type A DTC.
Conditions for Clearing the MIL/DTC
DTC P1400 is a Type A DTC.
Reference Information
Description and Operation
Engine Control Module Description (See: Powertrain Management/Computers and Control Systems/Description and Operation/Engine Control
Module Description)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Diagnostic Aids
Any loading of the engine that lowers engine RPM, such as with partial application of the clutch, A/C cycling etc., during the first 17 s of engine
run time may set this DTC.
Circuit/System Verification
1. Allow the engine to cool.
2. Start and idle the engine for at least 2 min.
3. DTC P1400 should run and pass.
Circuit/System Testing
* Inspect the air intake system for the following:
- Damage, restriction, or modification
- Dirty or deteriorating air filter element
- Crankcase ventilation system for correct operation-Refer to Crankcase Ventilation System Inspection/Diagnosis (See: Powertrain
Management/Emission Control Systems/Positive Crankcase Ventilation/Testing and Inspection).
- Water intrusion
- Vacuum leak and other un-metered air downstream of the mass air flow (MAF) sensor
- Intake manifold leak
* Inspect the exhaust system for the following:
- Water intrusion
- Exhaust leak
- Damaged, restricted, modified or enhanced exhaust system-Refer to Symptoms - Engine Exhaust (See: Engine, Cooling and
Exhaust/Exhaust System/Testing and Inspection/Symptoms - Engine Exhaust).
* Inspect the engine mechanical for items that could alter the air flow into the combustion chamber. Refer to Symptoms - Engine Mechanical (
See: Engine, Cooling and Exhaust/Engine/Testing and Inspection/Symptom Related Diagnostic Procedures/Symptoms - Engine Mechanical).
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
Sunday, November 3, 2019
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1955
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1955
* DTCs P0030, P0036, P0068, P0101, P0102, P0103, P0106, P0107, P0108, P0117, P0118, P0120, P0121, P0128, P0130, P0131, P0132,
P0133, P0134, P0135, P0136, P0137, P0138, P0140, P0141, P0201-P0208, P0220, P0300, P0301-P0304, P0442, P0443, P0446, P0449,
P0452, P0453, P0455, P0496, P1106, P1107, P1114, P1115, P1133, P1516, P2101, P2119, P2120, P2125, P2135, P2138, P2176 are not set.
* The engine is in Closed Loop status.
* The engine coolant temperature (ECT) is between -40 and +150锟斤拷C (-40 and +302锟斤拷F).
* The intake air temperature (IAT) is between -20 and +150锟斤拷C (-4 and +302锟斤拷F).
* The manifold absolute pressure (MAP) is between 10-255 kPa (1.45-37 psi).
* The vehicle speed is less than 134 km/h (83 mph).
* The engine speed is between 375-7,000 RPM.
* The mass air flow (MAF) is between 1-510 g/s.
* The barometric pressure (BARO) is more than 70 kPa (10.2 psi).
* The fuel level is more than 10 %.
* This diagnostic runs continuously when the above conditions have been met.
Conditions for Setting the DTC
* The average long term FT weighted average value is more or less than a calibrated value.
* The above condition is present for approximately 3 min after the Conditions for Running the DTC have been met.
Action Taken When the DTC Sets
The ECM records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the ECM stores this information in the
Failure Records. If the diagnostic reports a failure on the second ignition cycle the ECM records the operating conditions at the time of the failure.
The ECM writes the operating conditions to the Freeze Frame and updates the Failure Records. The ECM illuminates the malfunction indicator
lamp (MIL) when one of the following occur:
* The ECM detects the same fuel trim failure during 2 consecutive trips.
* The ECM detects any fuel trim failure during any subsequent trip if the conditions at the time of failure meet the following criteria:
- The engine load is within 20 % of the previous test that failed.
- The engine speed is within 375 RPM of the previous test that failed.
- The engine coolant temperature is in the same range of the previous test that failed.
Conditions for Clearing the MIL/DTC
* The ECM turns OFF the malfunction indicator lamp (MIL) at the beginning of the fourth ignition cycle, after 3 ignition cycles that the
diagnostic runs and does not fail.
* A current DTC, Last Test Failed, clears when the diagnostic runs and passes.
* A history DTC and related Freeze Frame data clears after 40 warm-up cycles, if no failures are reported by this or any other emission related
diagnostic.
* Clear the MIL and the DTC with a scan tool.
Reference Information
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Verification
* Disregard any transmission symptoms, antilock brake system (ABS) indicators, and traction control system (TCS) indicators until any fuel
trim faults are repaired. A fuel trim fault may cause default actions such as harsh shifts and illumination of the ABS/TCS indicators.
* E85 compatible engine only-Over estimation of the ethanol content will result in a rich shift of fuel trim values, and under-estimation will
result in a lean shift of fuel trim values. A fuel trim DTC may set if the learned alcohol content, Fuel Alcohol Content parameter on the scan
tool, is different than the measured alcohol content in the vehicle such that fuel trim values exceed failure threshold values. Refer to Fuel
Composition Diagnosis (See: Powertrain Management/Computers and Control Systems/Testing and Inspection/Component Tests and
General Diagnostics).
* Verify that other DTCs are not set.
* DTCs P0030, P0036, P0068, P0101, P0102, P0103, P0106, P0107, P0108, P0117, P0118, P0120, P0121, P0128, P0130, P0131, P0132,
P0133, P0134, P0135, P0136, P0137, P0138, P0140, P0141, P0201-P0208, P0220, P0300, P0301-P0304, P0442, P0443, P0446, P0449,
P0452, P0453, P0455, P0496, P1106, P1107, P1114, P1115, P1133, P1516, P2101, P2119, P2120, P2125, P2135, P2138, P2176 are not set.
* The engine is in Closed Loop status.
* The engine coolant temperature (ECT) is between -40 and +150锟斤拷C (-40 and +302锟斤拷F).
* The intake air temperature (IAT) is between -20 and +150锟斤拷C (-4 and +302锟斤拷F).
* The manifold absolute pressure (MAP) is between 10-255 kPa (1.45-37 psi).
* The vehicle speed is less than 134 km/h (83 mph).
* The engine speed is between 375-7,000 RPM.
* The mass air flow (MAF) is between 1-510 g/s.
* The barometric pressure (BARO) is more than 70 kPa (10.2 psi).
* The fuel level is more than 10 %.
* This diagnostic runs continuously when the above conditions have been met.
Conditions for Setting the DTC
* The average long term FT weighted average value is more or less than a calibrated value.
* The above condition is present for approximately 3 min after the Conditions for Running the DTC have been met.
Action Taken When the DTC Sets
The ECM records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the ECM stores this information in the
Failure Records. If the diagnostic reports a failure on the second ignition cycle the ECM records the operating conditions at the time of the failure.
The ECM writes the operating conditions to the Freeze Frame and updates the Failure Records. The ECM illuminates the malfunction indicator
lamp (MIL) when one of the following occur:
* The ECM detects the same fuel trim failure during 2 consecutive trips.
* The ECM detects any fuel trim failure during any subsequent trip if the conditions at the time of failure meet the following criteria:
- The engine load is within 20 % of the previous test that failed.
- The engine speed is within 375 RPM of the previous test that failed.
- The engine coolant temperature is in the same range of the previous test that failed.
Conditions for Clearing the MIL/DTC
* The ECM turns OFF the malfunction indicator lamp (MIL) at the beginning of the fourth ignition cycle, after 3 ignition cycles that the
diagnostic runs and does not fail.
* A current DTC, Last Test Failed, clears when the diagnostic runs and passes.
* A history DTC and related Freeze Frame data clears after 40 warm-up cycles, if no failures are reported by this or any other emission related
diagnostic.
* Clear the MIL and the DTC with a scan tool.
Reference Information
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Verification
* Disregard any transmission symptoms, antilock brake system (ABS) indicators, and traction control system (TCS) indicators until any fuel
trim faults are repaired. A fuel trim fault may cause default actions such as harsh shifts and illumination of the ABS/TCS indicators.
* E85 compatible engine only-Over estimation of the ethanol content will result in a rich shift of fuel trim values, and under-estimation will
result in a lean shift of fuel trim values. A fuel trim DTC may set if the learned alcohol content, Fuel Alcohol Content parameter on the scan
tool, is different than the measured alcohol content in the vehicle such that fuel trim values exceed failure threshold values. Refer to Fuel
Composition Diagnosis (See: Powertrain Management/Computers and Control Systems/Testing and Inspection/Component Tests and
General Diagnostics).
* Verify that other DTCs are not set.
Subscribe to:
Posts (Atom)