P0AF0, P0AF5, P0BD4, P0BD9, P0BDE, and P0BE3
* Ignition ON.
* Motor temperature is greater than -40锟斤拷C (-40锟斤拷F).
锟斤拷If motor temperature is less than -40锟斤拷C (-40锟斤拷F) at Ignition ON, the drive motor must operate at greater than 20 Nm (14.75 lb ft) for a
cumulative time of 1.5 minutes before the DTC will run.
Conditions for Setting the DTC
P0AEE, P0AF3, P0BD2, P0BD7, P0BDC, and P0BE1
* A 15锟斤拷C ( 27锟斤拷F) difference is observed between the individual inverter phase temperature sensor and the average of all the inverter phase
temperatures.
* The above condition is present for 4 seconds.
P0AEF, P0AF4, P0BD3, P0BD8, P0BDD, and P0BE2
The inverter phase temperature sensor is greater than 125锟斤拷C (275锟斤拷F) for 3 seconds.
P0AF0, P0AF5, P0BD4, P0BD9, P0BDE, and P0BE3
The inverter phase temperature sensor is less than -40锟斤拷C (-40锟斤拷F) for 3 seconds.
Action Taken When the DTC Sets
* DTCs P0AEE, P0AEF, P0AF0, P0AF3, P0AF4, P0AF5, P0BD2, P0BD3, P0BD4, P0BD7, P0BD8, P0BD9, P0BDC, P0BDD, P0BDE,
P0BE1, P0BE2 AND P0BE3 are Type B DTCs.
* The PIM commands the battery energy control module (BECM) to open the high voltage contactor relays.
Conditions for Clearing the DTC
DTCs P0AEE, P0AEF, P0AF0, P0AF3, P0AF4, P0AF5, P0BD2, P0BD3, P0BD4, P0BD7, P0BD8, P0BD9, P0BDC, P0BDD, P0BDE, P0BE1,
P0BE2 AND P0BE3 are Type B DTCs.
Reference Information
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Circuit/System Verification
1. Clear the DTC information.
2. Ignition OFF for 1 minute.
3. Operate the vehicle under the Conditions for Running the DTC.
4. Retest for DTCs P0AEE, P0AEF, P0AF0, P0AF3, P0AF4, P0AF5, P0BD2, P0BD3, P0BD4, P0BD7, P0BD8, P0BD9, P0BDC, P0BDD,
P0BDE, P0BE1, P0BE2 AND P0BE3.
Circuit/System Testing
Program the PIM with the latest software version and recheck for DTCs.
If the DTC resets after programming or if the PIM already contains the latest software version, replace the PIM.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
Control Module References (See: Testing and Inspection/Programming and Relearning) for PIM replacement, setup, and programming.
P0AEF
DTC P0AEE, P0AEF, P0AF0, P0AF3-P0AF5, P0BD2-P0BD4, P0BD7-P0BD9, P0BDC-P0BDE, or P0BE1-P0BE3
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
