2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 1776
瀚慖f the DTC resets, program the PIM with the latest software version and recheck for DTCs. If the DTC resets after programming or if the
PIM already contains the latest software version, replace the PIM.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
Control Module References (See: Testing and Inspection/Programming and Relearning) for PIM replacement, setup, and programming.
P018B
DTC P018B-P018D
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC P018B
- Fuel Pressure Sensor Performance
DTC P018C
- Fuel Pressure Sensor Circuit Low Voltage
DTC P018D
- Fuel Pressure Sensor Circuit High Voltage
Diagnostic Fault Information
Circuit/System Description
The fuel pressure sensor is located on the fuel line. The fuel pressure sensor monitors the fuel pressure in the fuel line. The fuel pump flow control
module monitors the voltage signal from the fuel pressure sensor.
Conditions for Running the DTC
* The engine is running.
* DTC P018C, P018D, P0231, P0232, P023F, P064A, P1255 or P06A6 are not active.
* DTC P0641 has not failed this ignition cycle.
* Fuel pump control is enabled and the fuel pump control state is normal.
* The engine has been running for at least 5 seconds.
Conditions for Setting the DTC
The fuel pump control module does not detect a change in the fuel rail pressure of at least 30 kPa (4.4 psi) when the fuel pump is operating. The
fuel rail pressure sensor performance diagnostic provides a means to detect fuel pressure sensor output that is stuck within the normal operating
range of the sensor.
Action Taken When the DTC Sets
DTC P018B, P018C and P018D are Type A DTCs.
Conditions for Clearing the DTC
DTC P018B, P018C and P018D are Type A DTCs.
Thursday, October 31, 2019
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1751
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1751
Component Connector End Views (See: Diagrams/Connector Views)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
* Heated Oxygen Sensor Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical
Diagnostic Procedures/Wiring Repairs/Heated Oxygen Sensor Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Verification
* Observe the DTC information with a scan tool. Verify there are no B52 HO2S heater or fuel trim DTCs set.
锟斤拷If any DTCs are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code Descriptions/Diagnostic
Trouble Code (DTC) List - Vehicle).
* Engine idling at operating temperature, observe the appropriate B52 HO2S parameter with a scan tool. Verify the following:
- The B52 HO2S 1 value should vary from below 200 mV to above 800 mV and respond to fueling changes.
- The B52 HO2S 2 value should change greater than 200 mV when the throttle is quickly cycled 3 times from closed to wide open and
back to closed after running the engine at 1,500 RPM for 30 s.
* Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the
conditions that you observed from the Freeze Frame/Failure Records data.
Circuit/System Testing
1. Verify none of the following conditions exist:
* Lean or rich fuel injectors-Refer to Fuel Injector Diagnosis (CH47976) (See: Powertrain Management/Fuel Delivery and Air
Induction/Fuel Injector/Testing and Inspection)Fuel Injector Diagnosis (J39021 or Scan Tool) (See: Powertrain Management/Fuel
Delivery and Air Induction/Fuel Injector/Testing and Inspection)
* Water intrusion in the B52 HO2S harness connector
* Low or high fuel system pressure-Refer to Fuel System Diagnosis (w/o FPCM) (See: Powertrain Management/Computers and Control
Systems/Testing and Inspection/Component Tests and General Diagnostics)Fuel System Diagnosis (FPCM) (See: Powertrain
Management/Computers and Control Systems/Testing and Inspection/Component Tests and General Diagnostics)
* Fuel that is contaminated-Refer to Alcohol/Contaminants-in-Fuel Diagnosis (Without Special Tool) (See: Powertrain
Management/Computers and Control Systems/Testing and Inspection/Component Tests and General
Diagnostics/Alcohol/Contaminants-in-Fuel Diagnosis (Without Special Tool))Alcohol/Contaminants-in-Fuel Diagnosis (Special Tool) (
See: Powertrain Management/Fuel Delivery and Air Induction/Fuel/Testing and Inspection/Alcohol/Contaminants-in-Fuel Diagnosis
(Special Tool))
* Fuel saturation of the evaporative emission (EVAP) canister
* Exhaust leaks near the B52 HO2S
* Engine vacuum leaks
* Engine oil consumption-Refer to Oil Consumption Diagnosis (See: Engine, Cooling and Exhaust/Engine/Testing and
Inspection/Component Tests and General Diagnostics/Oil Consumption Diagnosis)
* Engine coolant consumption-Refer to Loss of Coolant (See: Engine, Cooling and Exhaust/Cooling System/Testing and
Inspection/Symptom Related Diagnostic Procedures/Loss of Coolant)
锟斤拷If you find any of the above conditions, repair as necessary.
2. If all conditions test normal, test or replace the appropriate B52 HO2S.
Repair Instructions
Caution: Refer to Heated Oxygen Sensor Resistance Learn Reset Caution (See: Powertrain Management/Computers and Control
Component Connector End Views (See: Diagrams/Connector Views)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
* Heated Oxygen Sensor Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical
Diagnostic Procedures/Wiring Repairs/Heated Oxygen Sensor Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Verification
* Observe the DTC information with a scan tool. Verify there are no B52 HO2S heater or fuel trim DTCs set.
锟斤拷If any DTCs are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code Descriptions/Diagnostic
Trouble Code (DTC) List - Vehicle).
* Engine idling at operating temperature, observe the appropriate B52 HO2S parameter with a scan tool. Verify the following:
- The B52 HO2S 1 value should vary from below 200 mV to above 800 mV and respond to fueling changes.
- The B52 HO2S 2 value should change greater than 200 mV when the throttle is quickly cycled 3 times from closed to wide open and
back to closed after running the engine at 1,500 RPM for 30 s.
* Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the
conditions that you observed from the Freeze Frame/Failure Records data.
Circuit/System Testing
1. Verify none of the following conditions exist:
* Lean or rich fuel injectors-Refer to Fuel Injector Diagnosis (CH47976) (See: Powertrain Management/Fuel Delivery and Air
Induction/Fuel Injector/Testing and Inspection)Fuel Injector Diagnosis (J39021 or Scan Tool) (See: Powertrain Management/Fuel
Delivery and Air Induction/Fuel Injector/Testing and Inspection)
* Water intrusion in the B52 HO2S harness connector
* Low or high fuel system pressure-Refer to Fuel System Diagnosis (w/o FPCM) (See: Powertrain Management/Computers and Control
Systems/Testing and Inspection/Component Tests and General Diagnostics)Fuel System Diagnosis (FPCM) (See: Powertrain
Management/Computers and Control Systems/Testing and Inspection/Component Tests and General Diagnostics)
* Fuel that is contaminated-Refer to Alcohol/Contaminants-in-Fuel Diagnosis (Without Special Tool) (See: Powertrain
Management/Computers and Control Systems/Testing and Inspection/Component Tests and General
Diagnostics/Alcohol/Contaminants-in-Fuel Diagnosis (Without Special Tool))Alcohol/Contaminants-in-Fuel Diagnosis (Special Tool) (
See: Powertrain Management/Fuel Delivery and Air Induction/Fuel/Testing and Inspection/Alcohol/Contaminants-in-Fuel Diagnosis
(Special Tool))
* Fuel saturation of the evaporative emission (EVAP) canister
* Exhaust leaks near the B52 HO2S
* Engine vacuum leaks
* Engine oil consumption-Refer to Oil Consumption Diagnosis (See: Engine, Cooling and Exhaust/Engine/Testing and
Inspection/Component Tests and General Diagnostics/Oil Consumption Diagnosis)
* Engine coolant consumption-Refer to Loss of Coolant (See: Engine, Cooling and Exhaust/Cooling System/Testing and
Inspection/Symptom Related Diagnostic Procedures/Loss of Coolant)
锟斤拷If you find any of the above conditions, repair as necessary.
2. If all conditions test normal, test or replace the appropriate B52 HO2S.
Repair Instructions
Caution: Refer to Heated Oxygen Sensor Resistance Learn Reset Caution (See: Powertrain Management/Computers and Control
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 584
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 584
- Left Seat Assembly Horizontal Position Sensor Circuit Short to Ground or Open
DTC B2375 5A
- Left Seat Assembly Horizontal Position Sensor Circuit Plausibility Failure
Diagnostic Fault Information
Circuit Description
The position sensor that sets this diagnostic trouble code (DTC) is either attached to the seat directional motor drive cable or directly to the motor it
monitors. It receives a 5-volt reference and ground from the memory seat module (MSM). The sensor sends a voltage signal that varies with the
movement of the seat through the signal circuit to the MSM. Then based on this voltage signal, the MSM determines the position of the seat.
Conditions for Running the DTC
The memory seat module must be powered.
Conditions for Setting the DTC
B1825 01, B1850 01, B1860 01, B2355 01, B2365 01, B2375 01
If the MSM sees the analog input from this sensor is greater than 4.75 volts, the sensor will be considered out of range and the MSM will set this
DTC.
B1825 06, B1850 06, B1860 06, B2355 06, B2365 06, B2375 06
If the MSM sees the analog input from this sensor is less than 0.22 volts, the sensor will be considered out of range and the MSM will set this DTC.
B1825 5A, B1850 5A, B1860 5A, B2355 5A, B2365 5A, B2375 5A
This DTC will set, if the MSM is controlling a motor in one direction and its position sensor is tracking the motor in the opposite direction. The
sensor is either mounted or wired incorrectly, or the polarity of the motor control circuits are reversed.
Action Taken When the DTC Sets
The MSM disables the memory recall and easy exit/entry action commands of the motor monitored by the sensor. The motor will respond to
manual positioning commands.
Conditions for Clearing the DTC
* The current DTC will clear and set to history, when the MSM sees the analog input from the sensor as between 0.22-4.75 volts and the
ignition is cycled OFF then back to ACC or RUN.
* A history DTC will clear after 50 consecutive fault-free ignition cycles have occurred.
- Left Seat Assembly Horizontal Position Sensor Circuit Short to Ground or Open
DTC B2375 5A
- Left Seat Assembly Horizontal Position Sensor Circuit Plausibility Failure
Diagnostic Fault Information
Circuit Description
The position sensor that sets this diagnostic trouble code (DTC) is either attached to the seat directional motor drive cable or directly to the motor it
monitors. It receives a 5-volt reference and ground from the memory seat module (MSM). The sensor sends a voltage signal that varies with the
movement of the seat through the signal circuit to the MSM. Then based on this voltage signal, the MSM determines the position of the seat.
Conditions for Running the DTC
The memory seat module must be powered.
Conditions for Setting the DTC
B1825 01, B1850 01, B1860 01, B2355 01, B2365 01, B2375 01
If the MSM sees the analog input from this sensor is greater than 4.75 volts, the sensor will be considered out of range and the MSM will set this
DTC.
B1825 06, B1850 06, B1860 06, B2355 06, B2365 06, B2375 06
If the MSM sees the analog input from this sensor is less than 0.22 volts, the sensor will be considered out of range and the MSM will set this DTC.
B1825 5A, B1850 5A, B1860 5A, B2355 5A, B2365 5A, B2375 5A
This DTC will set, if the MSM is controlling a motor in one direction and its position sensor is tracking the motor in the opposite direction. The
sensor is either mounted or wired incorrectly, or the polarity of the motor control circuits are reversed.
Action Taken When the DTC Sets
The MSM disables the memory recall and easy exit/entry action commands of the motor monitored by the sensor. The motor will respond to
manual positioning commands.
Conditions for Clearing the DTC
* The current DTC will clear and set to history, when the MSM sees the analog input from the sensor as between 0.22-4.75 volts and the
ignition is cycled OFF then back to ACC or RUN.
* A history DTC will clear after 50 consecutive fault-free ignition cycles have occurred.
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 1775
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 1775
DTC Descriptor
DTC P16F9
- Control Module Shutdown Performance
Circuit/System Description
This diagnostic applies to internal microprocessor integrity conditions within the hybrid powertrain control module (HPCM). The HPCM and each
Motor Control Module (MCM) utilize a programmable logic device (PLD) to perform certain input and output functions. The HPCM monitors the
ability of the PLD to perform these functions.
Conditions for Running the DTC
* The control module runs the program to detect an internal fault when the key is ON.
* Ignition voltage is 8-18V.
Conditions for Setting the DTC
The control module has detected the internal PLD has not turned ON or OFF correctly.
Action Taken When the DTC Sets
* DTC P16F9 is a Type A DTC.
* The HPCM commands the battery energy control module (BECM) to open the high voltage contactor relays.
Conditions for Clearing the DTC
DTC P16F9 is a Type A DTC.
Diagnostic Aids
A low 12V battery condition, an intermittent loss of power, or loss of communication to the drive motor generator power inverter module assembly
(PIM) may set this DTC.
Reference Information
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Circuit/System Verification
1. Inspect for DTC P0562 or any communication U-code DTCs.
瀚慖f the specified DTCs have set, repair them first. Refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code
Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle).
2. Clear the DTC information.
3. Ignition OFF for 1 minute.
4. Ignition ON.
5. Retest for DTC P16F9.
Circuit/System Testing
1. Inspect for DTC P0562 or any communication DTCs.
瀚慖f the specified DTCs have set, repair them first. Refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code
Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle).
2. Ignition OFF.
3. Wait 2 minutes.
4. Disconnect PIM connector X1.
5. Wait 2 minutes.
6. Reconnect PIM connector X1.
7. Ignition ON, retest for DTC P16F9.
DTC Descriptor
DTC P16F9
- Control Module Shutdown Performance
Circuit/System Description
This diagnostic applies to internal microprocessor integrity conditions within the hybrid powertrain control module (HPCM). The HPCM and each
Motor Control Module (MCM) utilize a programmable logic device (PLD) to perform certain input and output functions. The HPCM monitors the
ability of the PLD to perform these functions.
Conditions for Running the DTC
* The control module runs the program to detect an internal fault when the key is ON.
* Ignition voltage is 8-18V.
Conditions for Setting the DTC
The control module has detected the internal PLD has not turned ON or OFF correctly.
Action Taken When the DTC Sets
* DTC P16F9 is a Type A DTC.
* The HPCM commands the battery energy control module (BECM) to open the high voltage contactor relays.
Conditions for Clearing the DTC
DTC P16F9 is a Type A DTC.
Diagnostic Aids
A low 12V battery condition, an intermittent loss of power, or loss of communication to the drive motor generator power inverter module assembly
(PIM) may set this DTC.
Reference Information
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Circuit/System Verification
1. Inspect for DTC P0562 or any communication U-code DTCs.
瀚慖f the specified DTCs have set, repair them first. Refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code
Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle).
2. Clear the DTC information.
3. Ignition OFF for 1 minute.
4. Ignition ON.
5. Retest for DTC P16F9.
Circuit/System Testing
1. Inspect for DTC P0562 or any communication DTCs.
瀚慖f the specified DTCs have set, repair them first. Refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code
Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle).
2. Ignition OFF.
3. Wait 2 minutes.
4. Disconnect PIM connector X1.
5. Wait 2 minutes.
6. Reconnect PIM connector X1.
7. Ignition ON, retest for DTC P16F9.
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1750
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1750
P013A P013C, P013E, or P014A
* Before the ECM can report DTC P013A, or P013C failed, DTCs P013E, P014A, P2270, and P2272 must run and pass.
* Before the ECM can report DTC P013E, or P014A failed, DTCs P2270 and P2272 must run and pass.
* DTCs P0030, P0036, P0053, P0054, P0101, P0102, P0103, P0106, P0107, P0108, P0120, P0121, P0122, P0123, P0131, P0132, P0133,
P0134, P0135, P0137, P0138, P013A, P013B, P013E, P013F, P0140, P0141, P0171, P0172, P0201, P0202, P0203, P0204, P0220, P0222,
P0223, P0300, P0442, P0443, P0446, P0449, P0455, P0496, P1133, P1174, P1516, P2101, P2119, P2135, P2176, P2270, P2271, P2A00 are
not set.
* The ignition 1 voltage is between 10-32 V.
* The learned heater resistance is valid.
* The fuel level is greater than 10 %.
* The engine run time is equal to or greater than 5 minutes.
* The accelerator pedal (APP) is steady.
* The torque converter clutch (TCC) is applied.
* The DTCs run once per ignition cycle, during decel fuel cut-off (DFCO), when the above conditions are met.
P013B P013D, P013F, or P014B
* Before the ECM can report DTC P013B, or P013D failed, DTCs P013A, P013C, P013E, P013F, P014A, P014B, P2270, P2271, P2272, and
P2273 must run and pass.
* Before the ECM can report DTC P013F, or P014B failed, DTCs P013A, P013C, P013E, P014A, P2270, P2271, P2272, and P2273 must run
and pass.
* DTCs P0030, P0036, P0053, P0054, P0101, P0102, P0103, P0106, P0107, P0108, P0120, P0121, P0122, P0123, P0131, P0132, P0133,
P0134, P0135, P0137, P0138, P013A, P013B, P013E, P013F, P0140, P0141, P0171, P0172, P0201, P0202, P0203, P0204, P0220, P0222,
P0223, P0300, P0442, P0443, P0446, P0449, P0455, P0496, P1133, P1174, P1516, P2101, P2119, P2135, P2176, P2270, P2271, P2A00 are
not set.
* The ignition 1 voltage is between 10-32 V.
* The learned heater resistance is valid.
* The fuel level is greater than 10 %.
* The engine run time is equal to or greater than 5 minutes.
* The DTCs run once per ignition cycle when the above conditions are met.
Conditions for Setting the DTC
P0133 or P0153
* The ECM detects that the HO2S 1 rich-to-lean or lean-to-rich average response time is greater than a calibrated value.
* The DTCs set within 100 s when the above condition is met.
P013A or P013C
The ECM detects that the accumulated mass air flow monitored during rich-to-lean transitions between 450-150 mV is greater than 75 grams.
P013B or P013D
The ECM detects that the accumulated mass air flow monitored during lean-to-rich transitions between 350-650 mV is greater than 75 grams.
P013E or P014A
The ECM detects that the O2 sensor voltage has not decreased below 450 mV within 42 grams of accumulated air flow.
P013F or P014B
The ECM detects that the O2 sensor voltage has not increased above 350 mV within 200 grams of accumulated air flow.
P1133 or P1153
* The ECM detects that the HO2S 1 rich-to-lean counts, or the lean-to-rich counts are less than a calibrated value.
* The DTCs set within 100 s when the above condition is met.
Action Taken When the DTC Sets
DTCs P0133, P013A, P013B, P013C, P013D, P013E, P013F, P014A, P014B, P0153, P1133, and P1153 are Type B DTCs.
Conditions for Clearing the DTC
DTCs P0133, P013A, P013B, P013C, P013D, P013E, P013F, P014A, P014B, P0153, P1133, and P1153 are Type B DTCs.
Reference Information
Schematic Reference
Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
P013A P013C, P013E, or P014A
* Before the ECM can report DTC P013A, or P013C failed, DTCs P013E, P014A, P2270, and P2272 must run and pass.
* Before the ECM can report DTC P013E, or P014A failed, DTCs P2270 and P2272 must run and pass.
* DTCs P0030, P0036, P0053, P0054, P0101, P0102, P0103, P0106, P0107, P0108, P0120, P0121, P0122, P0123, P0131, P0132, P0133,
P0134, P0135, P0137, P0138, P013A, P013B, P013E, P013F, P0140, P0141, P0171, P0172, P0201, P0202, P0203, P0204, P0220, P0222,
P0223, P0300, P0442, P0443, P0446, P0449, P0455, P0496, P1133, P1174, P1516, P2101, P2119, P2135, P2176, P2270, P2271, P2A00 are
not set.
* The ignition 1 voltage is between 10-32 V.
* The learned heater resistance is valid.
* The fuel level is greater than 10 %.
* The engine run time is equal to or greater than 5 minutes.
* The accelerator pedal (APP) is steady.
* The torque converter clutch (TCC) is applied.
* The DTCs run once per ignition cycle, during decel fuel cut-off (DFCO), when the above conditions are met.
P013B P013D, P013F, or P014B
* Before the ECM can report DTC P013B, or P013D failed, DTCs P013A, P013C, P013E, P013F, P014A, P014B, P2270, P2271, P2272, and
P2273 must run and pass.
* Before the ECM can report DTC P013F, or P014B failed, DTCs P013A, P013C, P013E, P014A, P2270, P2271, P2272, and P2273 must run
and pass.
* DTCs P0030, P0036, P0053, P0054, P0101, P0102, P0103, P0106, P0107, P0108, P0120, P0121, P0122, P0123, P0131, P0132, P0133,
P0134, P0135, P0137, P0138, P013A, P013B, P013E, P013F, P0140, P0141, P0171, P0172, P0201, P0202, P0203, P0204, P0220, P0222,
P0223, P0300, P0442, P0443, P0446, P0449, P0455, P0496, P1133, P1174, P1516, P2101, P2119, P2135, P2176, P2270, P2271, P2A00 are
not set.
* The ignition 1 voltage is between 10-32 V.
* The learned heater resistance is valid.
* The fuel level is greater than 10 %.
* The engine run time is equal to or greater than 5 minutes.
* The DTCs run once per ignition cycle when the above conditions are met.
Conditions for Setting the DTC
P0133 or P0153
* The ECM detects that the HO2S 1 rich-to-lean or lean-to-rich average response time is greater than a calibrated value.
* The DTCs set within 100 s when the above condition is met.
P013A or P013C
The ECM detects that the accumulated mass air flow monitored during rich-to-lean transitions between 450-150 mV is greater than 75 grams.
P013B or P013D
The ECM detects that the accumulated mass air flow monitored during lean-to-rich transitions between 350-650 mV is greater than 75 grams.
P013E or P014A
The ECM detects that the O2 sensor voltage has not decreased below 450 mV within 42 grams of accumulated air flow.
P013F or P014B
The ECM detects that the O2 sensor voltage has not increased above 350 mV within 200 grams of accumulated air flow.
P1133 or P1153
* The ECM detects that the HO2S 1 rich-to-lean counts, or the lean-to-rich counts are less than a calibrated value.
* The DTCs set within 100 s when the above condition is met.
Action Taken When the DTC Sets
DTCs P0133, P013A, P013B, P013C, P013D, P013E, P013F, P014A, P014B, P0153, P1133, and P1153 are Type B DTCs.
Conditions for Clearing the DTC
DTCs P0133, P013A, P013B, P013C, P013D, P013E, P013F, P014A, P014B, P0153, P1133, and P1153 are Type B DTCs.
Reference Information
Schematic Reference
Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 583
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 583
* Front Seat Adjuster Replacement (with HP2) ()Front Seat Adjuster Replacement (without HP2) ()
* Seat Lumbar Sub System Replacement ()
* Front Seat Recliner Actuator Motor Replacement ()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for MSM replacement, setup, and programming
B2375
DTC B1825, B1850, B1860, B2355, B2365, or B2375
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC B1825 01
- Seat Recline Position Sensor Circuit Short to Battery
DTC B1825 06
- Seat Recline Position Sensor Circuit Short to Ground or Open
DTC B1825 5A
- Seat Recline Position Sensor Circuit Plausibility Failure
DTC B1850 01
- Left Seat Lumbar Horizontal Position Sensor Circuit Short to Battery
DTC B1850 06
- Left Seat Lumbar Horizontal Position Sensor Circuit Short to Ground or Open
DTC B1850 5A
- Left Seat Lumbar Horizontal Position Sensor Circuit Plausibility Failure
DTC B1860 01
- Left Seat Lumbar Vertical Position Sensor Circuit Short to Battery
DTC B1860 06
- Left Seat Lumbar Vertical Position Sensor Circuit Short to Ground or Open
DTC B1860 5A
- Left Seat Lumbar Vertical Position Sensor Circuit Plausibility Failure
DTC B2355 01
- Left Seat Front Vertical Position Sensor Circuit Short to Battery
DTC B2355 06
- Left Seat Front Vertical Position Sensor Circuit Short to Ground or Open
DTC B2355 5A
- Left Seat Front Vertical Position Sensor Circuit Plausibility Failure
DTC B2365 01
- Left Seat Rear Vertical Position Sensor Circuit Short to Battery
DTC B2365 06
- Left Seat Rear Vertical Position Sensor Circuit Short to Ground or Open
DTC B2365 5A
- Left Seat Rear Vertical Position Sensor Circuit Plausibility Failure
DTC B2375 01
- Left Seat Assembly Horizontal Position Sensor Circuit Short to Battery
* Front Seat Adjuster Replacement (with HP2) ()Front Seat Adjuster Replacement (without HP2) ()
* Seat Lumbar Sub System Replacement ()
* Front Seat Recliner Actuator Motor Replacement ()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for MSM replacement, setup, and programming
B2375
DTC B1825, B1850, B1860, B2355, B2365, or B2375
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC B1825 01
- Seat Recline Position Sensor Circuit Short to Battery
DTC B1825 06
- Seat Recline Position Sensor Circuit Short to Ground or Open
DTC B1825 5A
- Seat Recline Position Sensor Circuit Plausibility Failure
DTC B1850 01
- Left Seat Lumbar Horizontal Position Sensor Circuit Short to Battery
DTC B1850 06
- Left Seat Lumbar Horizontal Position Sensor Circuit Short to Ground or Open
DTC B1850 5A
- Left Seat Lumbar Horizontal Position Sensor Circuit Plausibility Failure
DTC B1860 01
- Left Seat Lumbar Vertical Position Sensor Circuit Short to Battery
DTC B1860 06
- Left Seat Lumbar Vertical Position Sensor Circuit Short to Ground or Open
DTC B1860 5A
- Left Seat Lumbar Vertical Position Sensor Circuit Plausibility Failure
DTC B2355 01
- Left Seat Front Vertical Position Sensor Circuit Short to Battery
DTC B2355 06
- Left Seat Front Vertical Position Sensor Circuit Short to Ground or Open
DTC B2355 5A
- Left Seat Front Vertical Position Sensor Circuit Plausibility Failure
DTC B2365 01
- Left Seat Rear Vertical Position Sensor Circuit Short to Battery
DTC B2365 06
- Left Seat Rear Vertical Position Sensor Circuit Short to Ground or Open
DTC B2365 5A
- Left Seat Rear Vertical Position Sensor Circuit Plausibility Failure
DTC B2375 01
- Left Seat Assembly Horizontal Position Sensor Circuit Short to Battery
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 1774
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 1774
* The transmission control module shifts to a default gear and turns OFF.
Conditions for Clearing the DTC
DTC P16F8 is a Type A DTC
Diagnostic Aids
When attempting to set transmission control module internal DTCs, run the engine for at least 1 minute, and then shut the engine OFF for 30
seconds. Following this procedure will allow for a complete transmission control module shutdown. Program the transmission control module with
the latest software version and retest the DTC to see if the DTC resets.
Reference Information
Schematic Reference
Automatic Transmission Controls Schematics (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Diagrams)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information.
Circuit/System Verification
Verify that DTC P16F8 is not set.
If the DTC is set, program the Q8 control solenoid valve assembly. If the DTC resets, replace the Q8 control solenoid valve assembly.
Component Testing
Perform the Control Solenoid Valve and Transmission Control Module Assembly Inspection (See: Transmission and Drivetrain/Automatic
Transmission/Transaxle/Testing and Inspection/Component Tests and General Diagnostics/2ML70 - Automatic Transmission/Control Solenoid
Valve and Transmission Control Module Assembly Inspection).
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
Control Module References (See: Testing and Inspection/Programming and Relearning) for Q8 control solenoid valve assembly for replacement,
setup, and programming.
P16F9
DTC P16F9
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
* The transmission control module shifts to a default gear and turns OFF.
Conditions for Clearing the DTC
DTC P16F8 is a Type A DTC
Diagnostic Aids
When attempting to set transmission control module internal DTCs, run the engine for at least 1 minute, and then shut the engine OFF for 30
seconds. Following this procedure will allow for a complete transmission control module shutdown. Program the transmission control module with
the latest software version and retest the DTC to see if the DTC resets.
Reference Information
Schematic Reference
Automatic Transmission Controls Schematics (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Diagrams)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information.
Circuit/System Verification
Verify that DTC P16F8 is not set.
If the DTC is set, program the Q8 control solenoid valve assembly. If the DTC resets, replace the Q8 control solenoid valve assembly.
Component Testing
Perform the Control Solenoid Valve and Transmission Control Module Assembly Inspection (See: Transmission and Drivetrain/Automatic
Transmission/Transaxle/Testing and Inspection/Component Tests and General Diagnostics/2ML70 - Automatic Transmission/Control Solenoid
Valve and Transmission Control Module Assembly Inspection).
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
Control Module References (See: Testing and Inspection/Programming and Relearning) for Q8 control solenoid valve assembly for replacement,
setup, and programming.
P16F9
DTC P16F9
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
Subscribe to:
Posts (Atom)