2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 2889

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 2889

瀚慖f less than the specified value, test the signal circuit for a short to ground. If the circuit tests normal, replace the ECM.

瀚慖f greater than the specified value, test the signal circuit for a short to voltage. If the circuit tests normal, replace the ECM.

5. Ignition ON, install a 3 A fused jumper wire between the signal circuit terminal B and ground. Verify the scan tool HO2S parameter is less

than 60 mV.

瀚慖f greater than the specified range, test the signal circuit for an open/high resistance. If the circuits test normal, replace the ECM.

6. Verify none of the following conditions exist:

* Rich fuel injectors-Refer to Fuel Injector Diagnosis (CH47976) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel

Injector/Testing and Inspection)Fuel Injector Diagnosis (J39021 or Scan Tool) (See: Powertrain Management/Fuel Delivery and Air

Induction/Fuel Injector/Testing and Inspection)

* Water intrusion in the HO2S harness connector

* High fuel system pressure-Refer to Fuel System Diagnosis (w/o FPCM) (See: Powertrain Management/Computers and Control

Systems/Testing and Inspection/Component Tests and General Diagnostics)Fuel System Diagnosis (FPCM) (See: Powertrain

Management/Computers and Control Systems/Testing and Inspection/Component Tests and General Diagnostics)

* Fuel that is contaminated-Refer to Alcohol/Contaminants-in-Fuel Diagnosis (Without Special Tool) (See: Powertrain

Management/Computers and Control Systems/Testing and Inspection/Component Tests and General

Diagnostics/Alcohol/Contaminants-in-Fuel Diagnosis (Without Special Tool))Alcohol/Contaminants-in-Fuel Diagnosis (Special Tool) (

See: Powertrain Management/Fuel Delivery and Air Induction/Fuel/Testing and Inspection/Alcohol/Contaminants-in-Fuel Diagnosis

(Special Tool))

* Fuel saturation of the evaporative emission (EVAP) canister

瀚慖f you find any of the above conditions, repair as necessary.

7. If all circuits test normal, replace the appropriate HO2S.

Repair Instructions

Caution: Refer to Heated Oxygen Sensor Resistance Learn Reset Caution (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service Precautions/Heated Oxygen Sensor Resistance Learn Reset Caution).

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Heated Oxygen Sensor Replacement - Bank 2 Sensor 1 (1500 Series) (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 2 Sensor 1 (2500 Series) (See: Powertrain

Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)

* Heated Oxygen Sensor Replacement - Bank 2 Sensor 2 (1500 Series) (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 2 Sensor 2 (2500 Series) (See: Powertrain

Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming

P2518

DTC P2518

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC P2518 11

- A/C Refrigerant Low Side Fluid Pressure Sensor Circuit Above Maximum Threshold

DTC P2518 12

- A/C Refrigerant Low Side Fluid Pressure Sensor Circuit Below Minimum Threshold

Diagnostic Fault Information

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1068

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1068

瀚慖f warmer than the specified value, test the signal circuit for a short to ground. If the circuit tests normal, replace the K20 ECM.

Note: If the fuse in the jumper wire opens, the signal circuit is shorted to a voltage and the sensor may be damaged.

6. Ignition ON, install a 3 A fused jumper wire between the signal circuit terminal 1 and the low reference circuit terminal 2. Verify the ECT

sensor parameter is greater than 142掳C (288掳F).

瀚慖f less than the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace

the K20 ECM.

7. If all circuits test normal, test or replace the B34 ECT sensor.

Component Testing

1. Ignition OFF, disconnect the harness connector at the B34 engine coolant temperature (ECT) sensor.

Note: A thermometer can be used to test the sensor off the vehicle.

2. Test the ECT sensor by varying the sensor temperature while monitoring the sensor resistance. Compare the readings with the Temperature

Versus Resistance - Engine Coolant Temperature Sensor (See: Powertrain Management/Computers and Control

Systems/Specifications/Temperature Versus Resistance - Engine Coolant Temperature Sensor) table and verify that the resistance is within 5

% of the specification.

瀚慖f not within the specified range, replace the B34 ECT sensor.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Engine Coolant Temperature Sensor Replacement (LF1) (See: Engine, Cooling and Exhaust/Cooling System/Engine - Coolant Temperature

Sensor/Switch/Coolant Temperature Sensor/Switch (For Computer)/Service and Repair)Engine Coolant Temperature Sensor Replacement

(LAU) (See: Engine, Cooling and Exhaust/Cooling System/Engine - Coolant Temperature Sensor/Switch/Coolant Temperature

Sensor/Switch (For Computer)/Service and Repair)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming

P0117

DTC P0117 or P0118 (LAU)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC P0117

- Engine Coolant Temperature (ECT) Sensor Circuit Low Voltage

DTC P0118

- Engine Coolant Temperature (ECT) Sensor Circuit High Voltage

Diagnostic Fault Information

Typical Scan Tool Data