2010 Cadillac Truck SRX FWD V6-3.0L Page 1352

2010 Cadillac Truck SRX FWD V6-3.0L Page 1352

瀚慖f the circuits test normal, replace the K20 ECM.

Note: Testing for the following steps is performed on the fuel injector side of the multi-way harness connector. It may be necessary to

remove the intake manifold to isolate the condition.

4. Ignition OFF, measure the resistance between the appropriate high voltage supply circuit and ground. The DMM should display OL ohm.

瀚慖f less than the specified range, test the high voltage supply circuit and the high voltage control circuit for a short to ground. If the

circuits/connections test normal, test or replace the appropriate Q17 fuel injector(s).

5. Test for 2-3 ohm between the appropriate high voltage supply circuit and high voltage control circuit.

瀚慖f less than the specified range, test for a short between the high voltage supply circuit and high voltage control circuit. If the

circuits/connections test normal, test or replace the appropriate Q17 fuel injector(s).

瀚慖f greater than the specified range, test the high voltage supply circuit and high voltage control circuit for an open/high resistance. If the

circuits/connections test normal, test or replace the appropriate Q17 fuel injector.

Component Testing

* Fuel Injector Solenoid Coil Test (LAU) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Injector/Testing and Inspection

)Fuel Injector Solenoid Coil Test (LF1, LFW) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Injector/Testing and

Inspection)

* Fuel Injector Balance Test (LAU) (See: Powertrain Management/Computers and Control Systems/Testing and Inspection/Component Tests

and General Diagnostics/Fuel Injector Balance Test)Fuel Injector Balance Test (LF1, LFW) (See: Powertrain Management/Computers and

Control Systems/Testing and Inspection/Component Tests and General Diagnostics/Fuel Injector Balance Test)

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Fuel Injection Fuel Rail Assembly Replacement - Bank 1 (LF1) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel

Rail/Service and Repair/Fuel Injection Fuel Rail Assembly Replacement - Bank 1)

* Fuel Injection Fuel Rail Assembly Replacement - Bank 2 (LF1) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel

Rail/Service and Repair/Fuel Injection Fuel Rail Assembly Replacement - Bank 2)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming

P0267

DTC P0201, P0202, P0203, P0204, P0205, P0206, P0261, P0262, P0264, P0265, P0267, P0268, P0270, P0271, P0273, P0274, P0276, or P0277

(LF1)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC P0201

- Cylinder 1 Injector Control Circuit

DTC P0202

- Cylinder 2 Injector Control Circuit

DTC P0203

- Cylinder 3 Injector Control Circuit

DTC P0204

- Cylinder 4 Injector Control Circuit

DTC P0205

- Cylinder 5 Injector Control Circuit

2010 Cadillac Truck SRX FWD V6-3.0L Page 922

2010 Cadillac Truck SRX FWD V6-3.0L Page 922

瀚慖f the test lamp illuminates, test the low control circuit for a short to ground. If the circuit tests normal, replace the K20 ECM.

3. Ignition ON, verify that a test lamp does not illuminate between ground and the high control circuit terminal 2.

瀚慖f the test lamp illuminates, test the high control circuit for a short to voltage. If the circuit tests normal, replace the K20 ECM.

4. Ignition ON, command the Fuel Pressure Regulator ON with a scan tool. Verify that the test lamp illuminates.

瀚慖f the test lamp does not illuminate, test the high control circuit for a short to ground or an open/high resistance. If the circuit tests normal,

replace the K20 ECM.

5. Ignition OFF, connect a test lamp between the low control circuit terminal 1 and B+.

6. Ignition ON, command the Fuel Pressure Regulator ON with a scan tool. Verify that the test lamp illuminates.

瀚慖f the test lamp does not illuminate, test the low control circuit for a short to voltage or an open/high resistance. If the circuit tests normal,

replace the K20 ECM.

7. If all circuits test normal, test or replace the G18 high pressure fuel pump.

Component Testing

Static Test

1. Ignition OFF, disconnect the harness connector at the G18 high pressure fuel pump.

Note: The DMM and test leads must be calibrated to 0 ohm in order to prevent misdiagnosis.

2. Test for 9-11 ohm at 25掳C (77掳F) between the low control circuit terminal 1 and the high control circuit terminal 2.

瀚慖f not within the specified range, replace the G18 high pressure fuel pump.

3. Measure the resistance between each terminal and the high pressure fuel pump housing. The DMM should display OL.

瀚慖f less than the specified value, replace the G18 high pressure fuel pump.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Fuel Pump Replacement (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Pump/Service and Repair/Fuel Pump

Replacement)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming

P00C9

DTC P0090-P0092, P00C8, P00C9, or P00CA (LF1, LFW)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC P0090

- Fuel Pressure Regulator Control Circuit

DTC P0091

- Fuel Pressure Regulator Control Circuit Low Voltage

DTC P0092

- Fuel Pressure Regulator Control Circuit High Voltage

DTC P00C8

- Fuel Pressure Regulator High Control Circuit

2010 Cadillac Truck SRX FWD V6-3.0L Page 1266

2010 Cadillac Truck SRX FWD V6-3.0L Page 1266

瀚慖f the circuits test normal, replace the K20 ECM.

Note: Testing for the following steps is performed on the fuel injector side of the multi-way harness connector. It may be necessary to

remove the intake manifold to isolate the condition.

4. Ignition OFF, measure the resistance between the appropriate high voltage supply circuit and ground. The DMM should display OL ohm.

瀚慖f less than the specified range, test the high voltage supply circuit and the high voltage control circuit for a short to ground. If the

circuits/connections test normal, test or replace the appropriate Q17 fuel injector(s).

5. Test for 2-3 ohm between the appropriate high voltage supply circuit and high voltage control circuit.

瀚慖f less than the specified range, test for a short between the high voltage supply circuit and high voltage control circuit. If the

circuits/connections test normal, test or replace the appropriate Q17 fuel injector(s).

瀚慖f greater than the specified range, test the high voltage supply circuit and high voltage control circuit for an open/high resistance. If the

circuits/connections test normal, test or replace the appropriate Q17 fuel injector.

Component Testing

* Fuel Injector Solenoid Coil Test (LAU) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Injector/Testing and Inspection

)Fuel Injector Solenoid Coil Test (LF1, LFW) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Injector/Testing and

Inspection)

* Fuel Injector Balance Test (LAU) (See: Powertrain Management/Computers and Control Systems/Testing and Inspection/Component Tests

and General Diagnostics/Fuel Injector Balance Test)Fuel Injector Balance Test (LF1, LFW) (See: Powertrain Management/Computers and

Control Systems/Testing and Inspection/Component Tests and General Diagnostics/Fuel Injector Balance Test)

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Fuel Injection Fuel Rail Assembly Replacement - Bank 1 (LF1) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel

Rail/Service and Repair/Fuel Injection Fuel Rail Assembly Replacement - Bank 1)

* Fuel Injection Fuel Rail Assembly Replacement - Bank 2 (LF1) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel

Rail/Service and Repair/Fuel Injection Fuel Rail Assembly Replacement - Bank 2)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming

P0203

DTC P0201, P0202, P0203, P0204, P0205, P0206, P0261, P0262, P0264, P0265, P0267, P0268, P0270, P0271, P0273, P0274, P0276, or P0277

(LF1)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC P0201

- Cylinder 1 Injector Control Circuit

DTC P0202

- Cylinder 2 Injector Control Circuit

DTC P0203

- Cylinder 3 Injector Control Circuit

DTC P0204

- Cylinder 4 Injector Control Circuit

DTC P0205

- Cylinder 5 Injector Control Circuit

2010 Cadillac Truck SRX FWD V6-3.0L Page 2013

2010 Cadillac Truck SRX FWD V6-3.0L Page 2013

瀚慖f greater than the specified range, test the signal circuit terminal 3 for a short to voltage. If the circuit tests normal, replace the K20 ECM.

5. Install a 3 A fused jumper wire between the signal circuit terminal 3 and the 5 V reference circuit terminal 1. Verify the scan tool BARO

parameter is greater than 127 kPa (18.4 psi).

瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace

the K20 ECM.

6. If the circuits test normal, replace the B17 BARO sensor.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Throttle Inlet Absolute Pressure Sensor Replacement (LF1) (See: Powertrain Management/Computers and Control Systems/Absolute

Pressure Sensor/Service and Repair) for BARO sensor replacement

* Control Module References (See: Testing and Inspection/Programming and Relearning) for engine control module replacement, setup, and

programming

P2228

DTC P2227-P2229 or P2230 (LF1, LFW)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC P2227

- Barometric Pressure (BARO) Sensor Performance

DTC P2228

- Barometric Pressure (BARO) Sensor Circuit Low Voltage

DTC P2229

- Barometric Pressure (BARO) Sensor Circuit High Voltage

DTC P2230

- Barometric Pressure (BARO) Sensor Circuit Erratic

Diagnostic Fault Information

Typical Scan Tool Data

Circuit/System Description

2010 Cadillac Truck SRX FWD V6-3.0L Page 1256

2010 Cadillac Truck SRX FWD V6-3.0L Page 1256

replace the K20 ECM.

瀚慖f greater than the specified range, test the 5 V reference circuit for a short to voltage. If the circuit tests normal, replace the K20 ECM.

6. Ignition ON, verify the scan tool Fuel Rail Pressure Sensor voltage parameter is less than 0.02 V.

瀚慖f greater than the specified value, test the signal circuit for a short to voltage. If the circuit tests normal, replace the K20 ECM.

7. Connect a 3 A fused jumper wire between the signal circuit terminal 12 and the 5 V reference circuit terminal 11. Verify the scan tool Fuel

Rail Pressure Sensor voltage parameter is greater than 4.96 V.

瀚慖f less than the specified value, test the signal circuit for an open/high resistance or a short to ground. If the circuit tests normal, replace

the K20 ECM.

8. Ignition OFF, remove the intake manifold.

9. Connect the multi-way harness connector X198.

Note: Testing for steps 12 through 16 are performed at the fuel rail fuel pressure sensor connector.

10. Disconnect the B47 fuel rail fuel pressure sensor connector.

11. Remove the fuse that supplies B+ to terminal 52-X1 of the K20 ECM.

12. Ignition OFF, test for less than 5 ohm between the low reference circuit terminal C and ground.

瀚慖f greater than the specified range, test the low reference circuit for an open/high resistance.

13. Install the fuse that supplies B+ to terminal 52-X1 of the K20 ECM.

14. Ignition ON, test for 4.8-5.2 V between the 5 V reference circuit terminal A and ground.

瀚慖f less than the specified range, test the 5 V reference circuit for a short to ground or an open/high resistance.

瀚慖f greater than the specified range, test the 5 V reference circuit for a short to voltage.

15. Ignition ON, verify the scan tool Fuel Rail Pressure Sensor voltage parameter is less than 0.02 V.

瀚慖f greater than the specified value, test the signal circuit for a short to voltage.

16. Connect a 3 A fused jumper wire between the signal circuit terminal B and the 5 V reference circuit terminal A. Verify the scan tool Fuel

Rail Pressure Sensor voltage parameter is greater than 4.96 V.

瀚慖f less than the specified value, test the signal circuit for an open/high resistance or a short to ground.

17. If all circuits test normal, replace the B47 fuel rail fuel pressure sensor.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Fuel Pressure Sensor Replacement - Fuel Injection Fuel Rail (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Pressure

Sensor/Switch/Service and Repair/Fuel Pressure Sensor Replacement - Fuel Injection Fuel Rail)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming

P0193

DTC P0192 or P0193 (LF1)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC P0192

- Fuel Rail Pressure Sensor Circuit Low Voltage

DTC P0193

- Fuel Rail Pressure Sensor Circuit High Voltage

2010 Cadillac Truck SRX FWD V6-3.0L Page 1374

2010 Cadillac Truck SRX FWD V6-3.0L Page 1374

瀚慖f the circuits test normal, replace the K20 ECM.

Note: Testing for the following steps is performed on the fuel injector side of the multi-way harness connector. It may be necessary to

remove the intake manifold to isolate the condition.

4. Ignition OFF, measure the resistance between the appropriate high voltage supply circuit and ground. The DMM should display OL ohm.

瀚慖f less than the specified range, test the high voltage supply circuit and the high voltage control circuit for a short to ground. If the

circuits/connections test normal, test or replace the appropriate Q17 fuel injector(s).

5. Test for 2-3 ohm between the appropriate high voltage supply circuit and high voltage control circuit.

瀚慖f less than the specified range, test for a short between the high voltage supply circuit and high voltage control circuit. If the

circuits/connections test normal, test or replace the appropriate Q17 fuel injector(s).

瀚慖f greater than the specified range, test the high voltage supply circuit and high voltage control circuit for an open/high resistance. If the

circuits/connections test normal, test or replace the appropriate Q17 fuel injector.

Component Testing

* Fuel Injector Solenoid Coil Test (LAU) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Injector/Testing and Inspection

)Fuel Injector Solenoid Coil Test (LF1, LFW) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Injector/Testing and

Inspection)

* Fuel Injector Balance Test (LAU) (See: Powertrain Management/Computers and Control Systems/Testing and Inspection/Component Tests

and General Diagnostics/Fuel Injector Balance Test)Fuel Injector Balance Test (LF1, LFW) (See: Powertrain Management/Computers and

Control Systems/Testing and Inspection/Component Tests and General Diagnostics/Fuel Injector Balance Test)

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Fuel Injection Fuel Rail Assembly Replacement - Bank 1 (LF1) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel

Rail/Service and Repair/Fuel Injection Fuel Rail Assembly Replacement - Bank 1)

* Fuel Injection Fuel Rail Assembly Replacement - Bank 2 (LF1) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel

Rail/Service and Repair/Fuel Injection Fuel Rail Assembly Replacement - Bank 2)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming

P0276

DTC P0201, P0202, P0203, P0204, P0205, P0206, P0261, P0262, P0264, P0265, P0267, P0268, P0270, P0271, P0273, P0274, P0276, or P0277

(LF1)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC P0201

- Cylinder 1 Injector Control Circuit

DTC P0202

- Cylinder 2 Injector Control Circuit

DTC P0203

- Cylinder 3 Injector Control Circuit

DTC P0204

- Cylinder 4 Injector Control Circuit

DTC P0205

- Cylinder 5 Injector Control Circuit

2010 Cadillac Truck SRX FWD V6-3.0L Page 1115

2010 Cadillac Truck SRX FWD V6-3.0L Page 1115

瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the K20 ECM.

8. Ignition OFF, connect the red lead of the J 38522 to the signal circuit terminal A at the B75B MAF/IAT sensor harness connector. Connect

the battery voltage supply to the B+, and the black lead to ground.

9. Set the J 38522 signal switch to 5 V, the Frequency switch to 5K, and the Duty Cycle switch to Normal.

10. Ignition ON, observe the scan tool MAF Sensor parameter. The scan tool MAF Sensor parameter should be between 4,950-5,050 Hz.

瀚慖f the MAF Sensor parameter is not within the specified range, replace the K20 ECM.

11. If all other circuits test normal, test or replace the B75B MAF/IAT sensor.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the repair.

* Engine Coolant Temperature Sensor Replacement (LF1) (See: Engine, Cooling and Exhaust/Cooling System/Engine - Coolant Temperature

Sensor/Switch/Coolant Temperature Sensor/Switch (For Computer)/Service and Repair)Engine Coolant Temperature Sensor Replacement

(LAU) (See: Engine, Cooling and Exhaust/Cooling System/Engine - Coolant Temperature Sensor/Switch/Coolant Temperature

Sensor/Switch (For Computer)/Service and Repair)

* Mass Airflow Sensor with Intake Air Temperature Sensor Replacement (LF1) (See: Powertrain Management/Computers and Control

Systems/Air Temperature Sensor ( Ambient / Intake )/Service and Repair)Mass Airflow Sensor with Intake Air Temperature Sensor

Replacement (LAU) (See: Powertrain Management/Computers and Control Systems/Air Temperature Sensor ( Ambient / Intake )/Service

and Repair)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming

P0102

DTC P0102 or P0103 (LF1)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC P0102

- Mass Air Flow (MAF) Sensor Circuit Low Frequency

DTC P0103

- Mass Air Flow (MAF) Sensor Circuit High Frequency

Diagnostic Fault Information

Typical Scan Tool Data

Circuit/System Description

The mass air flow (MAF) sensor is integrated with the intake air temperature (IAT) sensor. The MAF sensor is an air flow meter that measures the

2010 Cadillac Truck SRX FWD V6-3.0L Page 1363

2010 Cadillac Truck SRX FWD V6-3.0L Page 1363

瀚慖f the circuits test normal, replace the K20 ECM.

Note: Testing for the following steps is performed on the fuel injector side of the multi-way harness connector. It may be necessary to

remove the intake manifold to isolate the condition.

4. Ignition OFF, measure the resistance between the appropriate high voltage supply circuit and ground. The DMM should display OL ohm.

瀚慖f less than the specified range, test the high voltage supply circuit and the high voltage control circuit for a short to ground. If the

circuits/connections test normal, test or replace the appropriate Q17 fuel injector(s).

5. Test for 2-3 ohm between the appropriate high voltage supply circuit and high voltage control circuit.

瀚慖f less than the specified range, test for a short between the high voltage supply circuit and high voltage control circuit. If the

circuits/connections test normal, test or replace the appropriate Q17 fuel injector(s).

瀚慖f greater than the specified range, test the high voltage supply circuit and high voltage control circuit for an open/high resistance. If the

circuits/connections test normal, test or replace the appropriate Q17 fuel injector.

Component Testing

* Fuel Injector Solenoid Coil Test (LAU) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Injector/Testing and Inspection

)Fuel Injector Solenoid Coil Test (LF1, LFW) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Injector/Testing and

Inspection)

* Fuel Injector Balance Test (LAU) (See: Powertrain Management/Computers and Control Systems/Testing and Inspection/Component Tests

and General Diagnostics/Fuel Injector Balance Test)Fuel Injector Balance Test (LF1, LFW) (See: Powertrain Management/Computers and

Control Systems/Testing and Inspection/Component Tests and General Diagnostics/Fuel Injector Balance Test)

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Fuel Injection Fuel Rail Assembly Replacement - Bank 1 (LF1) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel

Rail/Service and Repair/Fuel Injection Fuel Rail Assembly Replacement - Bank 1)

* Fuel Injection Fuel Rail Assembly Replacement - Bank 2 (LF1) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel

Rail/Service and Repair/Fuel Injection Fuel Rail Assembly Replacement - Bank 2)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming

P0271

DTC P0201, P0202, P0203, P0204, P0205, P0206, P0261, P0262, P0264, P0265, P0267, P0268, P0270, P0271, P0273, P0274, P0276, or P0277

(LF1)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC P0201

- Cylinder 1 Injector Control Circuit

DTC P0202

- Cylinder 2 Injector Control Circuit

DTC P0203

- Cylinder 3 Injector Control Circuit

DTC P0204

- Cylinder 4 Injector Control Circuit

DTC P0205

- Cylinder 5 Injector Control Circuit

2010 Cadillac Truck SRX FWD V6-3.0L Page 1447

2010 Cadillac Truck SRX FWD V6-3.0L Page 1447

瀚慖f the camshaft position active counter does not increment, replace the K20 ECM.

瀚慖f the circuits test normal, replace the B23 camshaft position sensor.

Component Testing

Note: You must perform the Circuit/System Testing before proceeding with Component Testing.

1. Inspect the B23 crankshaft position sensor for looseness and correct installation. Remove the crankshaft position sensor from the engine and

inspect the sensor and the O-ring for damage.

瀚慖f the sensor is loose, incorrectly installed, or damaged, repair or replace the B23 crankshaft position sensor.

2. Connect the crankshaft position sensor connector to the crankshaft position sensor.

3. Ignition ON, observe the applicable camshaft position active counter parameter with a scan tool. Pass a steel object by the tip of the sensor

repeatedly. The camshaft position active counter parameter should increment.

瀚慖f the function does not perform as specified, replace the B23 camshaft position sensor.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Camshaft Position Sensor Replacement - Bank 2 (Left Side) Exhaust (See: Powertrain Management/Computers and Control

Systems/Camshaft Position Sensor/Service and Repair/Camshaft Position Sensor Replacement - Bank 2 (Left Side) Exhaust)

* Camshaft Position Sensor Replacement - Bank 2 (Left Side) Intake (See: Powertrain Management/Computers and Control

Systems/Camshaft Position Sensor/Service and Repair/Camshaft Position Sensor Replacement - Bank 2 (Left Side) Intake)

* Camshaft Position Sensor Replacement - Bank 1 (Right Side) Intake (See: Powertrain Management/Computers and Control

Systems/Camshaft Position Sensor/Service and Repair/Camshaft Position Sensor Replacement - Bank 1 (Right Side) Intake)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for K20 ECM replacement, setup, and

programming

P0341

DTC P0341, P0346, P0366, or P0391 (LF1)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC P0341

- Intake Camshaft Position Sensor Performance Bank 1

DTC P0346

- Intake Camshaft Position Sensor Performance Bank 2

DTC P0366

- Exhaust Camshaft Position Sensor Performance Bank 1

DTC P0391

- Exhaust Camshaft Position Sensor Performance Bank 2

Diagnostic Fault Information

2010 Cadillac Truck SRX FWD V6-3.0L Page 1341

2010 Cadillac Truck SRX FWD V6-3.0L Page 1341

瀚慖f the circuits test normal, replace the K20 ECM.

Note: Testing for the following steps is performed on the fuel injector side of the multi-way harness connector. It may be necessary to

remove the intake manifold to isolate the condition.

4. Ignition OFF, measure the resistance between the appropriate high voltage supply circuit and ground. The DMM should display OL ohm.

瀚慖f less than the specified range, test the high voltage supply circuit and the high voltage control circuit for a short to ground. If the

circuits/connections test normal, test or replace the appropriate Q17 fuel injector(s).

5. Test for 2-3 ohm between the appropriate high voltage supply circuit and high voltage control circuit.

瀚慖f less than the specified range, test for a short between the high voltage supply circuit and high voltage control circuit. If the

circuits/connections test normal, test or replace the appropriate Q17 fuel injector(s).

瀚慖f greater than the specified range, test the high voltage supply circuit and high voltage control circuit for an open/high resistance. If the

circuits/connections test normal, test or replace the appropriate Q17 fuel injector.

Component Testing

* Fuel Injector Solenoid Coil Test (LAU) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Injector/Testing and Inspection

)Fuel Injector Solenoid Coil Test (LF1, LFW) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Injector/Testing and

Inspection)

* Fuel Injector Balance Test (LAU) (See: Powertrain Management/Computers and Control Systems/Testing and Inspection/Component Tests

and General Diagnostics/Fuel Injector Balance Test)Fuel Injector Balance Test (LF1, LFW) (See: Powertrain Management/Computers and

Control Systems/Testing and Inspection/Component Tests and General Diagnostics/Fuel Injector Balance Test)

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Fuel Injection Fuel Rail Assembly Replacement - Bank 1 (LF1) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel

Rail/Service and Repair/Fuel Injection Fuel Rail Assembly Replacement - Bank 1)

* Fuel Injection Fuel Rail Assembly Replacement - Bank 2 (LF1) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel

Rail/Service and Repair/Fuel Injection Fuel Rail Assembly Replacement - Bank 2)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming

P0262

DTC P0201, P0202, P0203, P0204, P0205, P0206, P0261, P0262, P0264, P0265, P0267, P0268, P0270, P0271, P0273, P0274, P0276, or P0277

(LF1)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC P0201

- Cylinder 1 Injector Control Circuit

DTC P0202

- Cylinder 2 Injector Control Circuit

DTC P0203

- Cylinder 3 Injector Control Circuit

DTC P0204

- Cylinder 4 Injector Control Circuit

DTC P0205

- Cylinder 5 Injector Control Circuit

2010 Cadillac CTS Sedan AWD V6-3.6L Page 965

2010 Cadillac CTS Sedan AWD V6-3.6L Page 965

normal, replace the K20 ECM.

4. Connect a 3 A fused jumper wire between the heater control circuit terminal E and ground. Observe the appropriate scan tool HO2S Heater

Control Circuit Low Voltage Test Status parameter. The parameter should transition from OK to Malfunction.

瀚慖f not the specified value, test the heater control circuit terminal E for an open/high resistance. If the circuit tests normal, replace the K20

ECM.

Note:

* Less than 10 ohm of additional resistance on the ignition voltage circuit, or control circuit may set a DTC. If there is resistance on a

circuit, the driver will remain ON and the scan tool HO2S High Voltage Test Status parameter will display OK.

* Performing this test may set additional DTCs.

5. Ignition OFF, connect a 10 A fused jumper wire between the control circuit terminal E and the ignition voltage circuit terminal D.

6. Engine idling, observe the appropriate HO2S Control Circuit High Voltage Test Status parameter. The parameter should transition from Not

Run to Malfunction.

瀚慖f not the specified value, test the control circuit and the ignition voltage circuit for high resistance. If the circuits test normal, replace the

K20 ECM.

7. If all circuits test normal, test or replace the appropriate B52 HO2S.

Repair Instructions

Caution: Refer to Heated Oxygen Sensor Resistance Learn Reset Caution (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service Precautions/Heated Oxygen Sensor Resistance Learn Reset Caution).

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 (LF1) (See: Powertrain Management/Computers and Control Systems/Oxygen

Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 (LLT) (See: Powertrain Management/Computers and

Control Systems/Oxygen Sensor/Service and Repair)

* Heated Oxygen Sensor Replacement - Bank 1 Sensor 2 (LF1) (See: Powertrain Management/Computers and Control Systems/Oxygen

Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 1 Sensor 2 (LLT) (See: Powertrain Management/Computers and

Control Systems/Oxygen Sensor/Service and Repair)

* Heated Oxygen Sensor Replacement - Bank 2 Sensor 1 (LF1) (See: Powertrain Management/Computers and Control Systems/Oxygen

Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 2 Sensor 1 (LLT) (See: Powertrain Management/Computers and

Control Systems/Oxygen Sensor/Service and Repair)

* Heated Oxygen Sensor Replacement - Bank 2 Sensor 2 (LF1) (See: Powertrain Management/Computers and Control Systems/Oxygen

Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 2 Sensor 2 (LLT) (See: Powertrain Management/Computers and

Control Systems/Oxygen Sensor/Service and Repair)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming

P062B

DTC P062B (w/LLT)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptor

DTC P062B

- Control Module Fuel Injector Control Performance

Circuit/System Description

This diagnostic applies to internal microprocessor integrity conditions within the engine control module (ECM).

Conditions for Running the DTC

* The engine is running or cranking.

* The ignition voltage is between 8-18 V.

2010 Cadillac Truck SRX AWD V6-3.0L Page 1089

2010 Cadillac Truck SRX AWD V6-3.0L Page 1089

瀚慖f a DTC failed this ignition, replace the K20 ECM.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

Control Module References (See: Testing and Inspection/Programming and Relearning) for engine control module replacement, setup, and

programming

Fuel Pump Control Module

DTC P0601-P0604, P0606, or P062F (Fuel Pump Control Module)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC P0601

- Control Module Read Only Memory (ROM)

DTC P0602

- Control Module Not Programmed

DTC P0603

- Control Module Long Term Memory Reset

DTC P0604

- Control Module Random Access Memory (RAM)

DTC P0606

- Control Module Internal Performance

DTC P062F

- Control Module Long Term Memory Performance

Circuit/System Description

The internal fault detection is handled inside the fuel pump control module. No external circuits are involved.

Conditions for Running the DTC

The fuel pump control module runs the program to detect an internal fault when power up is commanded. The only requirements are voltage and

ground. This program runs even if the voltage is out of the valid operating range.

Conditions for Setting the DTC

The fuel pump control module has detected an internal malfunction.

Action Taken When the DTC Sets

DTC P0601, P0602, P0603, P0604, P0606 and P062F are type A DTCs.

Conditions for Clearing the DTC

DTC P0601, P0602, P0603, P0604, P0606 and P062F are type A DTCs.

Reference Information

Description and Operation

Fuel System Description (LF1) (See: Powertrain Management/Fuel Delivery and Air Induction/Description and Operation/Fuel System

Description)Fuel System Description (LAU or LY7) (See: Powertrain Management/Fuel Delivery and Air Induction/Description and

2010 Cadillac Truck SRX AWD V6-3.0L Page 922

2010 Cadillac Truck SRX AWD V6-3.0L Page 922

瀚慖f the test lamp illuminates, test the low control circuit for a short to ground. If the circuit tests normal, replace the K20 ECM.

3. Ignition ON, verify that a test lamp does not illuminate between ground and the high control circuit terminal 2.

瀚慖f the test lamp illuminates, test the high control circuit for a short to voltage. If the circuit tests normal, replace the K20 ECM.

4. Ignition ON, command the Fuel Pressure Regulator ON with a scan tool. Verify that the test lamp illuminates.

瀚慖f the test lamp does not illuminate, test the high control circuit for a short to ground or an open/high resistance. If the circuit tests normal,

replace the K20 ECM.

5. Ignition OFF, connect a test lamp between the low control circuit terminal 1 and B+.

6. Ignition ON, command the Fuel Pressure Regulator ON with a scan tool. Verify that the test lamp illuminates.

瀚慖f the test lamp does not illuminate, test the low control circuit for a short to voltage or an open/high resistance. If the circuit tests normal,

replace the K20 ECM.

7. If all circuits test normal, test or replace the G18 high pressure fuel pump.

Component Testing

Static Test

1. Ignition OFF, disconnect the harness connector at the G18 high pressure fuel pump.

Note: The DMM and test leads must be calibrated to 0 ohm in order to prevent misdiagnosis.

2. Test for 9-11 ohm at 25掳C (77掳F) between the low control circuit terminal 1 and the high control circuit terminal 2.

瀚慖f not within the specified range, replace the G18 high pressure fuel pump.

3. Measure the resistance between each terminal and the high pressure fuel pump housing. The DMM should display OL.

瀚慖f less than the specified value, replace the G18 high pressure fuel pump.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Fuel Pump Replacement (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Pump/Service and Repair/Fuel Pump

Replacement)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming

P00C9

DTC P0090-P0092, P00C8, P00C9, or P00CA (LF1, LFW)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC P0090

- Fuel Pressure Regulator Control Circuit

DTC P0091

- Fuel Pressure Regulator Control Circuit Low Voltage

DTC P0092

- Fuel Pressure Regulator Control Circuit High Voltage

DTC P00C8

- Fuel Pressure Regulator High Control Circuit

2010 Cadillac Truck SRX AWD V6-3.0L Page 1266

2010 Cadillac Truck SRX AWD V6-3.0L Page 1266

瀚慖f the circuits test normal, replace the K20 ECM.

Note: Testing for the following steps is performed on the fuel injector side of the multi-way harness connector. It may be necessary to

remove the intake manifold to isolate the condition.

4. Ignition OFF, measure the resistance between the appropriate high voltage supply circuit and ground. The DMM should display OL ohm.

瀚慖f less than the specified range, test the high voltage supply circuit and the high voltage control circuit for a short to ground. If the

circuits/connections test normal, test or replace the appropriate Q17 fuel injector(s).

5. Test for 2-3 ohm between the appropriate high voltage supply circuit and high voltage control circuit.

瀚慖f less than the specified range, test for a short between the high voltage supply circuit and high voltage control circuit. If the

circuits/connections test normal, test or replace the appropriate Q17 fuel injector(s).

瀚慖f greater than the specified range, test the high voltage supply circuit and high voltage control circuit for an open/high resistance. If the

circuits/connections test normal, test or replace the appropriate Q17 fuel injector.

Component Testing

* Fuel Injector Solenoid Coil Test (LAU) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Injector/Testing and Inspection

)Fuel Injector Solenoid Coil Test (LF1, LFW) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Injector/Testing and

Inspection)

* Fuel Injector Balance Test (LAU) (See: Powertrain Management/Computers and Control Systems/Testing and Inspection/Component Tests

and General Diagnostics/Fuel Injector Balance Test)Fuel Injector Balance Test (LF1, LFW) (See: Powertrain Management/Computers and

Control Systems/Testing and Inspection/Component Tests and General Diagnostics/Fuel Injector Balance Test)

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Fuel Injection Fuel Rail Assembly Replacement - Bank 1 (LF1) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel

Rail/Service and Repair/Fuel Injection Fuel Rail Assembly Replacement - Bank 1)

* Fuel Injection Fuel Rail Assembly Replacement - Bank 2 (LF1) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel

Rail/Service and Repair/Fuel Injection Fuel Rail Assembly Replacement - Bank 2)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming

P0203

DTC P0201, P0202, P0203, P0204, P0205, P0206, P0261, P0262, P0264, P0265, P0267, P0268, P0270, P0271, P0273, P0274, P0276, or P0277

(LF1)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC P0201

- Cylinder 1 Injector Control Circuit

DTC P0202

- Cylinder 2 Injector Control Circuit

DTC P0203

- Cylinder 3 Injector Control Circuit

DTC P0204

- Cylinder 4 Injector Control Circuit

DTC P0205

- Cylinder 5 Injector Control Circuit

2010 Cadillac Truck SRX AWD V6-3.0L Page 1363

2010 Cadillac Truck SRX AWD V6-3.0L Page 1363

瀚慖f the circuits test normal, replace the K20 ECM.

Note: Testing for the following steps is performed on the fuel injector side of the multi-way harness connector. It may be necessary to

remove the intake manifold to isolate the condition.

4. Ignition OFF, measure the resistance between the appropriate high voltage supply circuit and ground. The DMM should display OL ohm.

瀚慖f less than the specified range, test the high voltage supply circuit and the high voltage control circuit for a short to ground. If the

circuits/connections test normal, test or replace the appropriate Q17 fuel injector(s).

5. Test for 2-3 ohm between the appropriate high voltage supply circuit and high voltage control circuit.

瀚慖f less than the specified range, test for a short between the high voltage supply circuit and high voltage control circuit. If the

circuits/connections test normal, test or replace the appropriate Q17 fuel injector(s).

瀚慖f greater than the specified range, test the high voltage supply circuit and high voltage control circuit for an open/high resistance. If the

circuits/connections test normal, test or replace the appropriate Q17 fuel injector.

Component Testing

* Fuel Injector Solenoid Coil Test (LAU) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Injector/Testing and Inspection

)Fuel Injector Solenoid Coil Test (LF1, LFW) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Injector/Testing and

Inspection)

* Fuel Injector Balance Test (LAU) (See: Powertrain Management/Computers and Control Systems/Testing and Inspection/Component Tests

and General Diagnostics/Fuel Injector Balance Test)Fuel Injector Balance Test (LF1, LFW) (See: Powertrain Management/Computers and

Control Systems/Testing and Inspection/Component Tests and General Diagnostics/Fuel Injector Balance Test)

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Fuel Injection Fuel Rail Assembly Replacement - Bank 1 (LF1) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel

Rail/Service and Repair/Fuel Injection Fuel Rail Assembly Replacement - Bank 1)

* Fuel Injection Fuel Rail Assembly Replacement - Bank 2 (LF1) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel

Rail/Service and Repair/Fuel Injection Fuel Rail Assembly Replacement - Bank 2)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming

P0271

DTC P0201, P0202, P0203, P0204, P0205, P0206, P0261, P0262, P0264, P0265, P0267, P0268, P0270, P0271, P0273, P0274, P0276, or P0277

(LF1)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC P0201

- Cylinder 1 Injector Control Circuit

DTC P0202

- Cylinder 2 Injector Control Circuit

DTC P0203

- Cylinder 3 Injector Control Circuit

DTC P0204

- Cylinder 4 Injector Control Circuit

DTC P0205

- Cylinder 5 Injector Control Circuit

2010 Cadillac CTS Sedan AWD V6-3.6L Page 1008

2010 Cadillac CTS Sedan AWD V6-3.6L Page 1008

瀚慖f greater than the specified range, test the signal circuit terminal 3 for a short to voltage. If the circuit tests normal, replace the K20 ECM.

6. Install a 3 A fused jumper wire between the signal circuit terminal 3 and the 5 V reference circuit terminal 1. Verify the scan tool MAP

Sensor parameter is greater than 127 kPa.

瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace

the K20 ECM.

7. If the circuits test normal, test or replace the B74 MAP sensor.

Component Testing

Note: You must perform the Circuit/System Testing in order to verify the integrity of the MAP sensor circuits before proceeding with the

Component Testing.

Skewed Signal Test

1. Using the following steps and referencing the table below will determine if the MAP sensor is skewed.

2. Ignition ON, engine OFF, observe the MAP Sensor scan tool parameter.

3. Use the observed MAP Sensor scan tool parameter that is closest to a value that is indicated in the first column.

THEN

4. Using the J 23738-A - Mityvac or the J 35555 - Metal Mityvac to apply 5 in Hg of vacuum to the B74 MAP sensor, the parameter in the first

column should decrease by 17 kPa. The acceptable range is indicated in the second column.

5. Using the J 23738-A - Mityvac or the J 35555 - Metal Mityvac to apply 10 in Hg of vacuum to the B74 MAP sensor, the parameter in the

first column should decrease by 34 kPa. The acceptable range is indicated in the third column.

Erratic Signal Test

1. Ignition OFF, remove the B74 MAP sensor.

2. Install a 3 A fused jumper wire between the 5 V reference circuit terminal 1 and the corresponding terminal of the B74 MAP sensor.

3. Install a jumper wire between the low reference circuit terminal 2 of the B74 MAP sensor and ground.

4. Install a jumper wire at terminal 3 of the B74 MAP sensor.

5. Connect a DMM between the jumper wire from terminal 3 of the B74 MAP sensor and ground.

6. Ignition ON, with the J 23738-A - Mityvac or J 35555 - Metal Mityvac , slowly apply vacuum to the sensor while observing the voltage on

the DMM. The voltage should vary between 0-5.2 V, without any spikes or dropouts.

瀚慖f the voltage reading is erratic, replace the B74 MAP sensor.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming

P0107

DTC P0107 or P0108 (w/LF1)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provide an overview of each diagnostic category.

2010 Cadillac Truck SRX AWD V6-3.0L Page 1352

2010 Cadillac Truck SRX AWD V6-3.0L Page 1352

瀚慖f the circuits test normal, replace the K20 ECM.

Note: Testing for the following steps is performed on the fuel injector side of the multi-way harness connector. It may be necessary to

remove the intake manifold to isolate the condition.

4. Ignition OFF, measure the resistance between the appropriate high voltage supply circuit and ground. The DMM should display OL ohm.

瀚慖f less than the specified range, test the high voltage supply circuit and the high voltage control circuit for a short to ground. If the

circuits/connections test normal, test or replace the appropriate Q17 fuel injector(s).

5. Test for 2-3 ohm between the appropriate high voltage supply circuit and high voltage control circuit.

瀚慖f less than the specified range, test for a short between the high voltage supply circuit and high voltage control circuit. If the

circuits/connections test normal, test or replace the appropriate Q17 fuel injector(s).

瀚慖f greater than the specified range, test the high voltage supply circuit and high voltage control circuit for an open/high resistance. If the

circuits/connections test normal, test or replace the appropriate Q17 fuel injector.

Component Testing

* Fuel Injector Solenoid Coil Test (LAU) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Injector/Testing and Inspection

)Fuel Injector Solenoid Coil Test (LF1, LFW) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Injector/Testing and

Inspection)

* Fuel Injector Balance Test (LAU) (See: Powertrain Management/Computers and Control Systems/Testing and Inspection/Component Tests

and General Diagnostics/Fuel Injector Balance Test)Fuel Injector Balance Test (LF1, LFW) (See: Powertrain Management/Computers and

Control Systems/Testing and Inspection/Component Tests and General Diagnostics/Fuel Injector Balance Test)

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Fuel Injection Fuel Rail Assembly Replacement - Bank 1 (LF1) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel

Rail/Service and Repair/Fuel Injection Fuel Rail Assembly Replacement - Bank 1)

* Fuel Injection Fuel Rail Assembly Replacement - Bank 2 (LF1) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel

Rail/Service and Repair/Fuel Injection Fuel Rail Assembly Replacement - Bank 2)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming

P0267

DTC P0201, P0202, P0203, P0204, P0205, P0206, P0261, P0262, P0264, P0265, P0267, P0268, P0270, P0271, P0273, P0274, P0276, or P0277

(LF1)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC P0201

- Cylinder 1 Injector Control Circuit

DTC P0202

- Cylinder 2 Injector Control Circuit

DTC P0203

- Cylinder 3 Injector Control Circuit

DTC P0204

- Cylinder 4 Injector Control Circuit

DTC P0205

- Cylinder 5 Injector Control Circuit

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2034

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2034

replace the K20 ECM.

瀚慖f greater than the specified range, test the 5 V reference circuit for a short to voltage. If the circuit tests normal, replace the K20 ECM.

4. Ignition ON, test for 4.8-5.2 V between the camshaft position signal circuit terminal C and ground.

瀚慖f less than the specified range, test the signal circuit for an open/high resistance or short to ground. If the circuit tests normal, replace the

K20 ECM.

瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the K20 ECM.

5. Ignition OFF, connect a fused jumper wire to the camshaft position signal circuit terminal C.

6. Ignition ON, momentarily touch the other the other end of the fused jumper wire to the battery negative post. The scan tool should show the

Camshaft Position Active counter incrementing.

瀚慖f the Camshaft Position Active counter increments, test or replace the B23 camshaft position sensor.

瀚慖f the Camshaft Position Active counter does not increment, replace the K20 ECM.

Component Testing

Note: You must perform the Circuit/System Testing before proceeding with Component Testing.

1. Inspect the camshaft position sensor for correct installation. Remove the camshaft position sensor from the engine and inspect the sensor

O-ring for damage.

瀚慖f the sensor is loose, incorrectly installed, or damaged, replace the B23 camshaft position sensor.

2. Connect the camshaft position sensor harness connector to the B23 camshaft position sensor.

3. Ignition ON, engine OFF. Observe the Camshaft Position Active counter parameter on the scan tool.

4. Pass a flat steel object across the tip of the sensor repeatedly. The Camshaft Position Active counter parameter should increment with each

pass of the steel object.

瀚慖f the parameter does not increment, replace the B23 camshaft position sensor.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Camshaft Position Sensor Replacement (See: Powertrain Management/Computers and Control Systems/Camshaft Position Sensor/Service

and Repair)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming

P0341

DTC P0341

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptor

DTC P0341

- Camshaft Position Sensor Performance

Diagnostic Fault Information

Circuit/System Description

2010 Cadillac Truck SRX AWD V6-3.0L Page 1256

2010 Cadillac Truck SRX AWD V6-3.0L Page 1256

replace the K20 ECM.

瀚慖f greater than the specified range, test the 5 V reference circuit for a short to voltage. If the circuit tests normal, replace the K20 ECM.

6. Ignition ON, verify the scan tool Fuel Rail Pressure Sensor voltage parameter is less than 0.02 V.

瀚慖f greater than the specified value, test the signal circuit for a short to voltage. If the circuit tests normal, replace the K20 ECM.

7. Connect a 3 A fused jumper wire between the signal circuit terminal 12 and the 5 V reference circuit terminal 11. Verify the scan tool Fuel

Rail Pressure Sensor voltage parameter is greater than 4.96 V.

瀚慖f less than the specified value, test the signal circuit for an open/high resistance or a short to ground. If the circuit tests normal, replace

the K20 ECM.

8. Ignition OFF, remove the intake manifold.

9. Connect the multi-way harness connector X198.

Note: Testing for steps 12 through 16 are performed at the fuel rail fuel pressure sensor connector.

10. Disconnect the B47 fuel rail fuel pressure sensor connector.

11. Remove the fuse that supplies B+ to terminal 52-X1 of the K20 ECM.

12. Ignition OFF, test for less than 5 ohm between the low reference circuit terminal C and ground.

瀚慖f greater than the specified range, test the low reference circuit for an open/high resistance.

13. Install the fuse that supplies B+ to terminal 52-X1 of the K20 ECM.

14. Ignition ON, test for 4.8-5.2 V between the 5 V reference circuit terminal A and ground.

瀚慖f less than the specified range, test the 5 V reference circuit for a short to ground or an open/high resistance.

瀚慖f greater than the specified range, test the 5 V reference circuit for a short to voltage.

15. Ignition ON, verify the scan tool Fuel Rail Pressure Sensor voltage parameter is less than 0.02 V.

瀚慖f greater than the specified value, test the signal circuit for a short to voltage.

16. Connect a 3 A fused jumper wire between the signal circuit terminal B and the 5 V reference circuit terminal A. Verify the scan tool Fuel

Rail Pressure Sensor voltage parameter is greater than 4.96 V.

瀚慖f less than the specified value, test the signal circuit for an open/high resistance or a short to ground.

17. If all circuits test normal, replace the B47 fuel rail fuel pressure sensor.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Fuel Pressure Sensor Replacement - Fuel Injection Fuel Rail (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Pressure

Sensor/Switch/Service and Repair/Fuel Pressure Sensor Replacement - Fuel Injection Fuel Rail)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming

P0193

DTC P0192 or P0193 (LF1)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC P0192

- Fuel Rail Pressure Sensor Circuit Low Voltage

DTC P0193

- Fuel Rail Pressure Sensor Circuit High Voltage

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1818

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1818

瀚慖f greater than the specified range, test the signal circuit for an open/high resistance. If the circuit tests normal, replace the K20 ECM.

5. If all circuits test normal, replace the appropriate B52 HO2S.

Repair Instructions

Caution: Refer to Heated Oxygen Sensor Resistance Learn Reset Caution (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service Precautions/Heated Oxygen Sensor Resistance Learn Reset Caution).

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 (1500 Series) (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 (2500 Series) (See: Powertrain

Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)

* Heated Oxygen Sensor Replacement - Bank 1 Sensor 2 (1500 Series) (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 1 Sensor 2 (2500 Series) (See: Powertrain

Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)

* Heated Oxygen Sensor Replacement - Bank 2 Sensor 1 (1500 Series) (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 2 Sensor 1 (2500 Series) (See: Powertrain

Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)

* Heated Oxygen Sensor Replacement - Bank 2 Sensor 2 (1500 Series) (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 2 Sensor 2 (2500 Series) (See: Powertrain

Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)

* Control Module References (See: Testing and Inspection/Programming and Relearning)for ECM replacement, setup, and programming

P0153

DTC P0133, P013A-P013F, P014A, P014B, P0153, P1133, or P1153

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC P0133

- HO2S Slow Response Bank 1 Sensor 1

DTC P013A

- HO2S Slow Response Rich to Lean Bank 1 Sensor 2

DTC P013B

- HO2S Slow Response Lean to Rich Bank 1 Sensor 2

DTC P013C

- HO2S Slow Response Rich to Lean Bank 2 Sensor 2

DTC P013D

- HO2S Slow Response Lean to Rich Bank 2 Sensor 2

DTC P013E

- HO2S Delayed Response Rich to Lean Bank 1 Sensor 2

DTC P013F

- HO2S Delayed Response Lean to Rich Bank 1 Sensor 2

DTC P014A

- HO2S Delayed Response Rich to Lean Bank 2 Sensor 2

DTC P014B

- HO2S Delayed Response Lean to Rich Bank 2 Sensor 2

DTC P0153

- HO2S Slow Response Bank 2 Sensor 1