2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 2714
Reference Information
Schematic Reference
Automatic Transmission Controls Schematics (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Diagrams)
Connector End View Reference
* Component Connector End Views (See: Diagrams/Connector Views)
* Inline Harness Connector End Views (See: Power and Ground Distribution/Multiple Junction Connector/Diagrams)
Description and Operation
* Transmission General Description (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Description and
Operation/6L45/6L50/6L80/6L90 - Automatic Transmission/Transmission General Description)
* Transmission Component and System Description (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Description and
Operation/6L45/6L50/6L80/6L90 - Automatic Transmission/Transmission Component and System Description)
* Electronic Component Description (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Description and
Operation/6L45/6L50/6L80/6L90 - Automatic Transmission/Electronic Component Description)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Special Tools
DT-47825-10 - Jumper Harness
Circuit/System Verification
1. Engine running in Park position. Move the gear shifter lever into each gear position and back into Park position. Verify with a scan tool the
following test status parameters display OK:
* Line Pressure Control Solenoid Performance Test Status
* Line Pressure Control Solenoid Control Circuit High Voltage Test Status
* Line Pressure Control Solenoid Control Circuit Low Voltage Test Status
2. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the
conditions that you observed from the Freeze Frame/Failure Records data.
Circuit/System Testing
Note: You must perform the Circuit/System Verification first.
1. Ignition OFF, remove the Q8 control solenoid valve assembly. Refer to Control Solenoid Valve and Transmission Control Module Assembly
Replacement (See: Powertrain Management/Transmission Control Systems/Actuators and Solenoids - Transmission and
Drivetrain/Actuators and Solenoids - A/T/Shift Solenoid/Service and Repair).
2. Perform the Control Solenoid Valve and Transmission Control Module Assembly Inspection (See: Transmission and Drivetrain/Automatic
Transmission/Transaxle/Testing and Inspection/Component Tests and General Diagnostics/6L45/6L50/6L80/6L90 - Automatic
Transmission/Control Solenoid Valve and Transmission Control Module Assembly Inspection).
3. Place the Q8 control solenoid valve assembly on a clean work surface near the transmission assembly.
4. Connect DT-47825-10 - jumper harness between the vehicle wire harness electrical connector, and the Q8 control solenoid valve assembly
electrical connector.
5. Ignition ON, verify with a scan tool the following test status parameters display OK:
* Line Pressure Control Solenoid Performance Test Status
* Line Pressure Control Solenoid Control Circuit High Voltage Test Status
