2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 2208
Circuit/System Testing
1. Ignition ON, engine OFF.
2. Seal the EVAP system using the Purge/Seal function with a scan tool.
3. Start the engine.
4. Observe the FTP sensor with a scan tool. The Fuel Tank Pressure Sensor parameter should be less than 1.7 volts after 90 seconds.
瀚慖f the Fuel Tank Pressure Sensor parameter is greater than the specified range, replace the EVAP canister purge solenoid valve.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
Evaporative Emission Canister Purge Solenoid Valve Replacement (See: Powertrain Management/Emission Control Systems/Evaporative
Emissions System/Canister Purge Solenoid/Service and Repair)
P0506
DTC P0506 or P0507
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provide an overview of each diagnostic category.
DTC Descriptors
DTC P0506
- Idle Speed Low
DTC P0507
- Idle Speed High
Circuit/System Description
The throttle actuator control (TAC) motor is controlled by the engine control module (ECM). The DC motor located in the throttle body drives the
throttle blade. In order to decrease idle speed, along with spark and fuel delivery changes the ECM commands the throttle closed reducing air flow
into the engine and the idle speed decreases. In order to increase idle speed, the ECM commands the throttle plate open allowing more air to pass
the throttle plate.
Conditions for Running the DTC
* DTCs P0068, P0101, P0102, P0103, P0112, P0113, P0116, P0117, P0118, P0120, P0121, P0122, P0123, P0128, P0171, P0172, P0174,
P0175, P0201, P0202, P0203, P0204, P0205, P0206, P0207, P0208, P0220, P0221, P0222, P0223, P0300-P0308, P0351-P0358, P0461-
P0463, P0496, P0502, P0503, P0606, P0722, P0723, P0806-P0808, P1516, P2066-P2068, P2101, P2135, P2227-P2230 are not set.
* The engine is operating for at least 60 s.
* The engine is idling for greater than 10 s.
* The barometric pressure (BARO) is greater than 70 kPa (11 psi).
* The engine coolant temperature (ECT) is greater than 60掳C (140掳F).
* The intake air temperature (IAT) is warmer than -20掳C (-4掳F).
* The vehicle speed is less than 3 km/h (2 mph).
* The commanded engine speed is steady within 25 RPM.
* The transmission is not changing gears.
* The torque converter clutch (TCC) is not changing states.
* The manual transmission clutch pedal position is between 20-88 percent - If equipped.
* The manual transmission clutch is not depressed - If equipped.
* The power take-off (PTO) is not active - If equipped.
* The transfer case is not in 4WD Low - If equipped.
* A scan tool output control is not active.
* The system voltage is between11-18 V.
* DTC P0506 and P0507 run continuously when the above conditions are met for greater than 10 s.
Conditions for Setting the DTC
CADILLAC Diagnostic and Repair Information ,Wiring Diagrams. DTC. TSB. Types: TSB, DTC, Wiring Diagrams, OEM Procedures. Trusted by more than 400,000 technicians. OEM accurate fix for faster repairs. Repair Procedures and Labor Times. Factory Auto Repair info. Request A Demo Today. Factory-Correct Diagrams. Factory Part Numbers. Maintenance Schedules. Repair Procedures. Labor Times. Types: TSB, DTC.