2010 Cadillac Truck Escalade AWD V8-6.2L Page 135
* Control circuit terminal 6 X1
* Control circuit terminal 8 X1
* Control circuit terminal 7 X1
锟斤拷If greater than the specified range, test the control circuit for a short to voltage. If the circuit tests normal, replace the SDM.
4. Ignition OFF, test for greater than 25 ohm between the control circuit terminals listed below and ground on the SDM side of the connector:
* Control circuit terminal 5 X1
* Control circuit terminal 6 X1
* Control circuit terminal 7 X1
* Control circuit terminal 8 X1
锟斤拷If less than the specified range, test the control circuit for a short to ground. If the circuit tests normal, replace the SDM.
5. Install a 3 A fused jumper wire between the control circuit terminals listed below.
* Passenger instrument panel airbag stage 1 terminal 5 and 6 X1
* Passenger instrument panel airbag stage 2 terminal 8 and 7 X1
6. Verify the scan tool Deployment Loop Resistance parameter is less than 2 ohm.
锟斤拷If greater than the specified range, test both control circuits terminals for an open/high resistance. If the circuits test normal, replace the
SDM.
7. Disconnect the passenger instrument panel air bag harness connector.
8. With the appropriate load tool adaptor, connect special tool J 38715-A in place of the air bag.
9. Ignition ON, test for less than 11 V between the control circuit terminals listed below and ground:
* Control circuit terminal A1
* Control circuit terminal A2
* Control circuit terminal B1
* Control circuit terminal B2
锟斤拷If greater than the specified range, test the control circuit for a short to voltage.
10. Ignition OFF, test for greater than 25 ohm between the control circuit terminals listed below and ground:
* Control circuit terminal A1
* Control circuit terminal A2
* Control circuit terminal B1
* Control circuit terminal B2
锟斤拷If less than the specified range, test the control circuit for a short to ground.
11. Ignition OFF, test for less than 5 ohm between the control circuit terminals listed below:
* X200 control circuit terminal A1 and passenger instrument panel air bag harness connector control circuit terminal A1
* X200 control circuit terminal A2 and passenger instrument panel air bag harness connector control circuit terminal A2
* X200 control circuit terminal B1 and passenger instrument panel air bag harness connector control circuit terminal B1
* X200 control circuit terminal B2 andpassenger instrument panel air bag harness connector control circuit terminal B2
锟斤拷If greater than the specified range, test the control circuit for an open/high resistance.
12. If all circuits test normal, replace the passenger instrument panel air bag.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* SIR/SRS Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Wiring Repairs/SIR/SRS Wiring Repairs)
* Instrument Panel Inflatable Restraint Module Replacement (See: Restraints and Safety Systems/Air Bag Systems/Air Bag/Service and
Repair/Removal and Replacement/Instrument Panel Inflatable Restraint Module Replacement)
* Steering Wheel Inflatable Restraint Module Replacement (See: Restraints and Safety Systems/Air Bag Systems/Air Bag/Service and
Repair/Removal and Replacement/Steering Wheel Inflatable Restraint Module Replacement)
* Steering Wheel Inflatable Restraint Module Coil Replacement (See: Restraints and Safety Systems/Air Bag Systems/Clockspring Assembly
/ Spiral Cable/Service and Repair/Removal and Replacement)
* Inflatable Restraint Side Impact Sensor Replacement (Front Side Door) (See: Restraints and Safety Systems/Air Bag Systems/Impact
Sensor/Service and Repair/Inflatable Restraint Side Impact Sensor Replacement (Front Side Door))Inflatable Restraint Side Impact Sensor
CADILLAC Diagnostic and Repair Information ,Wiring Diagrams. DTC. TSB. Types: TSB, DTC, Wiring Diagrams, OEM Procedures. Trusted by more than 400,000 technicians. OEM accurate fix for faster repairs. Repair Procedures and Labor Times. Factory Auto Repair info. Request A Demo Today. Factory-Correct Diagrams. Factory Part Numbers. Maintenance Schedules. Repair Procedures. Labor Times. Types: TSB, DTC.