2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 1783
Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Fuel System Description (See: Powertrain Management/Computers and Control Systems/Description and Operation/Fuel System Description)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning)for scan tool information
Circuit/System Verification
Ignition ON, command the fuel pump ON and OFF using the scan tool ECM fuel pump output control. The fuel pump should turn ON and OFF.
Circuit/System Testing
1. Ignition OFF, disconnect the harness connector at the G12 fuel pump.
2. Connect a test lamp between the control circuit terminal D and ground.
3. Ignition ON, command the G12 fuel pump ON and OFF with a scan tool. The test lamp should turn ON and OFF, as commanded.
瀚慖f the test lamp is always ON, test the control circuit for a short to voltage. If the circuit tests normal, replace the K27 fuel pump control
module.
瀚慖f the test lamp is always OFF, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace
the K27 fuel pump control module.
4. Ignition OFF, connect a test lamp between the control circuit terminal D and the low reference circuit terminal A.
5. Ignition ON, command the G12 fuel pump ON with a scan tool. The test lamp should illuminate.
瀚慖f the test lamp does not illuminate, test the low reference circuit terminal A for a short to voltage or an open/high resistance. If the circuit
tests normal, replace the K27 fuel pump control module.
6. If all circuits test normal, replace the fuel tank G12 fuel pump module.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Fuel Tank Fuel Pump Module Replacement (2500 LWB - 43.5L (11.5 gal) Tank Rear) (See: Powertrain Management/Fuel Delivery and Air
Induction/Fuel Pump/Service and Repair/Fuel Tank Fuel Pump Module Replacement (2500 LWB - 43.5L (11.5 Gal) Tank Rear))Fuel Tank
Fuel Pump Module Replacement (2500 LWB - 98.4L (26 gal) Tank Front) (See: Powertrain Management/Fuel Delivery and Air
Induction/Fuel Pump/Service and Repair/Fuel Tank Fuel Pump Module Replacement (2500 LWB - 98.4L (26 Gal) Tank Front))Fuel Tank
Fuel Pump Module Replacement (1500 SWB - 98.4L (26 gal) Tank + E85) (See: Powertrain Management/Fuel Delivery and Air
Induction/Fuel Pump/Service and Repair/Fuel Tank Fuel Pump Module Replacement (1500 SWB - 98.4L (26 Gal) Tank + E85))Fuel Tank
Fuel Pump Module Replacement (1500 Series) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Pump/Service and
Repair/Fuel Tank Fuel Pump Module Replacement (1500 Series))Fuel Tank Fuel Pump Module Replacement (1500 LWB - 117.3L (31 gal)
Tank + E85) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Pump/Service and Repair/Fuel Tank Fuel Pump Module
Replacement (1500 LWB - 117.3L (31 Gal) Tank + E85))
* Control Module References (See: Testing and Inspection/Programming and Relearning)for fuel pump control module replacement, setup,
