2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 1785
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning)for scan tool information
Circuit/System Testing
1. Ignition OFF, disconnect the harness connector at the K27 fuel pump control module.
2. Ignition OFF, connect a test lamp between the control circuit terminal 13 and ground.
3. Ignition ON, command the fuel pump ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the
commanded states.
瀚慖f the test lamp is always ON, test the control circuit for a short to voltage. If the circuit tests normal, replace the K20 ECM.
瀚慖f the test lamp is always OFF, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace
the K20 ECM.
4. If all circuits test normal, replace the K27 fuel pump control module.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
Control Module References (See: Testing and Inspection/Programming and Relearning)for ECM or fuel pump control module replacement, setup,
and programming
P0030
DTC P0030, P0036, P0050, P0053, P0054, P0056, P0059, P0060, P0135, P0141, P0155, or P0161
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC P0030
- HO2S Heater Control Circuit Bank 1 Sensor 1
DTC P0036
- HO2S Heater Control Circuit Bank 1 Sensor 2
DTC P0050
- HO2S Heater Control Circuit Bank 2 Sensor 1
DTC P0053
- HO2S Heater Resistance Bank 1 Sensor 1
DTC P0054
- HO2S Heater Resistance Bank 1 Sensor 2
DTC P0056
- HO2S Heater Control Circuit Bank 2 Sensor 2
DTC P0059
- HO2S Heater Resistance Bank 2 Sensor 1
DTC P0060
- HO2S Heater Resistance Bank 2 Sensor 2
DTC P0135
- HO2S Heater Performance Bank 1 Sensor 1
DTC P0141
- HO2S Heater Performance Bank 1 Sensor 2
Friday, November 1, 2019
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1760
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1760
1. Start the engine.
2. Allow the engine to reach normal operating temperature.
3. Allow the engine to idle.
4. Observe the DTC information with a scan tool.
锟斤拷If the scan tool indicates P0016 has failed this ignition cycle, continue with the Circuit/System Testing.
5. Operate the vehicle within the Conditions For Running the DTC. You may also operate the vehicle within the conditions that are captured in
the Freeze Frame/Failure Records Data List.
Circuit/System Testing
Note: You must perform the Circuit/System Verification before proceeding with Circuit/System Testing.
1. Inspect the engine front cover area, or review the service history of the vehicle for any recent repairs involving the timing chain, timing chain
tensioner, camshaft, crankshaft, camshaft actuator, or sprockets.
锟斤拷If recent repairs were made, inspect the timing chain, timing chain tensioner, and both sprockets for proper timing alignment or indexing.
2. Remove the engine front cover, refer to Engine Front Cover Replacement (See: Engine, Cooling and Exhaust/Engine/Timing
Components/Timing Cover/Service and Repair) and inspect the timing chain, timing chain tensioner, and sprockets for wear or damage.
锟斤拷If any components are worn or damage, replace as necessary.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
With 6.0L or 6.2L
DTC P0016 (With 6.0L or 6.2L)
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptor
DTC P0016
- Crankshaft Position (CKP) Camshaft Position (CMP) Correlation
Circuit/System Description
The engine control module (ECM) uses the crankshaft position (CKP) sensor and the camshaft position (CMP) sensor pulses to monitor the
correlation between the crankshaft and the camshaft position. The crankshaft reluctor wheel consists of a 60-tooth pattern with 2 teeth missing for
the reference gap. Each tooth is evenly spaced 6 degrees apart, except for the reference gap. The camshaft reluctor wheel has 4 teeth, 2 narrow, and
2 wide. The 4 trailing edges of each tooth are evenly spaced at 90 degrees apart around the circumference of the camshaft sprocket. With the engine
running, and the CMP actuator in the parked position, the ECM expects the camshaft signal pulses to occur 36 crankshaft degrees before top dead
center (BTDC) for cylinder number 1, and every 90 degrees thereafter.
Conditions for Running the DTC
* DTC P0335, P0336, P0340, P0341, P0641, or P0651 is not set.
* The engine is running.
* The engine speed is less than 2,000 RPM.
* The CMP actuator is commanded to the parked position.
* DTC P0016 runs continuously when the above conditions are met.
Conditions for Setting the DTC
The ECM detects that the CMP sensor pulses occur more than 11 crank degrees before, or 11 crank degrees after, nominal position for 24 out of 30
1. Start the engine.
2. Allow the engine to reach normal operating temperature.
3. Allow the engine to idle.
4. Observe the DTC information with a scan tool.
锟斤拷If the scan tool indicates P0016 has failed this ignition cycle, continue with the Circuit/System Testing.
5. Operate the vehicle within the Conditions For Running the DTC. You may also operate the vehicle within the conditions that are captured in
the Freeze Frame/Failure Records Data List.
Circuit/System Testing
Note: You must perform the Circuit/System Verification before proceeding with Circuit/System Testing.
1. Inspect the engine front cover area, or review the service history of the vehicle for any recent repairs involving the timing chain, timing chain
tensioner, camshaft, crankshaft, camshaft actuator, or sprockets.
锟斤拷If recent repairs were made, inspect the timing chain, timing chain tensioner, and both sprockets for proper timing alignment or indexing.
2. Remove the engine front cover, refer to Engine Front Cover Replacement (See: Engine, Cooling and Exhaust/Engine/Timing
Components/Timing Cover/Service and Repair) and inspect the timing chain, timing chain tensioner, and sprockets for wear or damage.
锟斤拷If any components are worn or damage, replace as necessary.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
With 6.0L or 6.2L
DTC P0016 (With 6.0L or 6.2L)
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptor
DTC P0016
- Crankshaft Position (CKP) Camshaft Position (CMP) Correlation
Circuit/System Description
The engine control module (ECM) uses the crankshaft position (CKP) sensor and the camshaft position (CMP) sensor pulses to monitor the
correlation between the crankshaft and the camshaft position. The crankshaft reluctor wheel consists of a 60-tooth pattern with 2 teeth missing for
the reference gap. Each tooth is evenly spaced 6 degrees apart, except for the reference gap. The camshaft reluctor wheel has 4 teeth, 2 narrow, and
2 wide. The 4 trailing edges of each tooth are evenly spaced at 90 degrees apart around the circumference of the camshaft sprocket. With the engine
running, and the CMP actuator in the parked position, the ECM expects the camshaft signal pulses to occur 36 crankshaft degrees before top dead
center (BTDC) for cylinder number 1, and every 90 degrees thereafter.
Conditions for Running the DTC
* DTC P0335, P0336, P0340, P0341, P0641, or P0651 is not set.
* The engine is running.
* The engine speed is less than 2,000 RPM.
* The CMP actuator is commanded to the parked position.
* DTC P0016 runs continuously when the above conditions are met.
Conditions for Setting the DTC
The ECM detects that the CMP sensor pulses occur more than 11 crank degrees before, or 11 crank degrees after, nominal position for 24 out of 30
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 592
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 592
Circuit/System Description
When the heated seat function is active, the heated seat module (HSM) supplies battery voltage through the element supply voltage circuit to the
seat heater elements. The HSM controls the seat temperature by providing a pulse width modulated (PWM) ground through the heated seat element
control circuit to the seat heater elements. The HSM then monitors the current flow through the heating element and the temperature sensor rate of
change to verify correct operation.
Conditions for Running the DTC
The HSM must be powered and the heated seat must be enabled.
Conditions for Setting the DTC
B2425 04 or B2430 04
The HSM does not detect a temperature change within 210 seconds.
B2425 0A or B2430 0A
The HSM detects that the set point temperature has not been reached within 8.5 minutes.
B2425 0B, B2425 0E, B2430 0B, or B2430 0E
By measuring output current, the HSM calculates that the heating element resistance is below the minimum resistance.
B2425 0C, B2445 0D, B2430 0C, or B2430 0D
By measuring output current, the HSM calculates that the heating element resistance is above the maximum resistance.
B2425 1F or B2430 1F
The temperature sensor voltage is erratic or changes suddenly.
Circuit/System Description
When the heated seat function is active, the heated seat module (HSM) supplies battery voltage through the element supply voltage circuit to the
seat heater elements. The HSM controls the seat temperature by providing a pulse width modulated (PWM) ground through the heated seat element
control circuit to the seat heater elements. The HSM then monitors the current flow through the heating element and the temperature sensor rate of
change to verify correct operation.
Conditions for Running the DTC
The HSM must be powered and the heated seat must be enabled.
Conditions for Setting the DTC
B2425 04 or B2430 04
The HSM does not detect a temperature change within 210 seconds.
B2425 0A or B2430 0A
The HSM detects that the set point temperature has not been reached within 8.5 minutes.
B2425 0B, B2425 0E, B2430 0B, or B2430 0E
By measuring output current, the HSM calculates that the heating element resistance is below the minimum resistance.
B2425 0C, B2445 0D, B2430 0C, or B2430 0D
By measuring output current, the HSM calculates that the heating element resistance is above the maximum resistance.
B2425 1F or B2430 1F
The temperature sensor voltage is erratic or changes suddenly.
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 3144
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 3144
* Do not replace a control module reporting a U-code. The U-code identifies which control module needs to be diagnosed for a communication
issue.
* Communication may be available between the BCM and the scan tool with either the low or high speed GMLAN serial data system
inoperative. This condition is due to the BCM using both the low and high speed GMLAN systems.
* Use to determine if the module uses high or low speed GMLAN serial data communications.
* Some control modules may not have internal protection for specific control circuits and may open a B+ or ignition fuse. If a fuse is open and
the B+ or ignition circuit is not shorted to ground, ensure none of the control circuits are shorted to ground before replacing the control
module.
* This diagnostic can be used for any control module that is not communicating, regardless of the type of serial data circuit it is connected to,
providing the vehicle is equipped with the control module.
Reference Information
Schematic Reference
* Data Communication Schematics (See: Powertrain Management/Computers and Control Systems/Information Bus/Diagrams/Electrical
Diagrams)
* Antilock Brake System Schematics (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical
Diagrams) for the ABS - Hybrid
* Antilock Brake System Schematics (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical
Diagrams) for the ABS - Non-Hybrid Less than 3900 kg (8600 lb) GVW
* Antilock Brake System Schematics (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical
Diagrams) for the ABS - Non-Hybrid Greater than/Equal to 3900 kg (8600 lb) GVW
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Data Link Communications Description and Operation (See: Powertrain Management/Computers and Control Systems/Information
Bus/Description and Operation)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Testing
1. Ignition OFF, disconnect the harness connector of the yaw rate sensor.
2. Ignition ON, verify that a test lamp illuminates between the module voltage circuit and ground.
瀚慖f the test lamp does not illuminate, test the circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the
EBCM.
3. Ignition OFF, test for less than 5 ohms between the module ground circuits and ground.
瀚慖f greater than the specified value, test the ground circuit for an open/high resistance. If the circuit tests normal, replace the EBCM.
4. If all circuits test normal, replace the yaw rate sensor.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* GMLAN Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Wiring Repairs/GMLAN Wiring Repairs)
* ABS Description and Operation (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Description and
Operation/ABS Description and Operation) for the ABS - Hybrid
* Vehicle Yaw Sensor with Vehicle Lateral Accelerometer Replacement (See: Brakes and Traction Control/Antilock Brakes / Traction
Control Systems/Yaw Rate Sensor/Service and Repair/Less than 3900 kg (8600 lb) GVW) for the ABS - Non-Hybrid Less than 3900 kg
* Do not replace a control module reporting a U-code. The U-code identifies which control module needs to be diagnosed for a communication
issue.
* Communication may be available between the BCM and the scan tool with either the low or high speed GMLAN serial data system
inoperative. This condition is due to the BCM using both the low and high speed GMLAN systems.
* Use to determine if the module uses high or low speed GMLAN serial data communications.
* Some control modules may not have internal protection for specific control circuits and may open a B+ or ignition fuse. If a fuse is open and
the B+ or ignition circuit is not shorted to ground, ensure none of the control circuits are shorted to ground before replacing the control
module.
* This diagnostic can be used for any control module that is not communicating, regardless of the type of serial data circuit it is connected to,
providing the vehicle is equipped with the control module.
Reference Information
Schematic Reference
* Data Communication Schematics (See: Powertrain Management/Computers and Control Systems/Information Bus/Diagrams/Electrical
Diagrams)
* Antilock Brake System Schematics (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical
Diagrams) for the ABS - Hybrid
* Antilock Brake System Schematics (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical
Diagrams) for the ABS - Non-Hybrid Less than 3900 kg (8600 lb) GVW
* Antilock Brake System Schematics (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical
Diagrams) for the ABS - Non-Hybrid Greater than/Equal to 3900 kg (8600 lb) GVW
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Data Link Communications Description and Operation (See: Powertrain Management/Computers and Control Systems/Information
Bus/Description and Operation)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Testing
1. Ignition OFF, disconnect the harness connector of the yaw rate sensor.
2. Ignition ON, verify that a test lamp illuminates between the module voltage circuit and ground.
瀚慖f the test lamp does not illuminate, test the circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the
EBCM.
3. Ignition OFF, test for less than 5 ohms between the module ground circuits and ground.
瀚慖f greater than the specified value, test the ground circuit for an open/high resistance. If the circuit tests normal, replace the EBCM.
4. If all circuits test normal, replace the yaw rate sensor.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* GMLAN Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Wiring Repairs/GMLAN Wiring Repairs)
* ABS Description and Operation (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Description and
Operation/ABS Description and Operation) for the ABS - Hybrid
* Vehicle Yaw Sensor with Vehicle Lateral Accelerometer Replacement (See: Brakes and Traction Control/Antilock Brakes / Traction
Control Systems/Yaw Rate Sensor/Service and Repair/Less than 3900 kg (8600 lb) GVW) for the ABS - Non-Hybrid Less than 3900 kg
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 1784
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 1784
DTC P025A
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions)provides an overview of each diagnostic category.
DTC Descriptor
DTC P025A
- Fuel Pump Control Module Enable Circuit
Diagnostic Fault Information
Circuit/System Description
The engine control module (ECM) supplies voltage to the fuel pump control module when the ECM detects that the ignition is on. The voltage from
the ECM to the fuel pump control module remains active for 2 seconds, unless the engine is in crank or run. While this voltage is being received,
the fuel pump control module supplies a varying voltage to the fuel tank pump module in order to maintain the desired fuel rail pressure.
Conditions for Running the DTC
The ignition is ON.
Conditions for Setting the DTC
The GMLAN serial data message from the ECM to the fuel pump control module does not agree with the state of the control enable voltage signal
supplied from the ECM to the fuel pump control module for more than 2 seconds.
Action Taken When the DTC Sets
DTC P025A is a Type A DTC.
Conditions for Clearing the DTC
DTC P025A is a Type A DTC.
Reference Information
Schematic Reference
Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Fuel System Description (See: Powertrain Management/Computers and Control Systems/Description and Operation/Fuel System Description)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
DTC P025A
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions)provides an overview of each diagnostic category.
DTC Descriptor
DTC P025A
- Fuel Pump Control Module Enable Circuit
Diagnostic Fault Information
Circuit/System Description
The engine control module (ECM) supplies voltage to the fuel pump control module when the ECM detects that the ignition is on. The voltage from
the ECM to the fuel pump control module remains active for 2 seconds, unless the engine is in crank or run. While this voltage is being received,
the fuel pump control module supplies a varying voltage to the fuel tank pump module in order to maintain the desired fuel rail pressure.
Conditions for Running the DTC
The ignition is ON.
Conditions for Setting the DTC
The GMLAN serial data message from the ECM to the fuel pump control module does not agree with the state of the control enable voltage signal
supplied from the ECM to the fuel pump control module for more than 2 seconds.
Action Taken When the DTC Sets
DTC P025A is a Type A DTC.
Conditions for Clearing the DTC
DTC P025A is a Type A DTC.
Reference Information
Schematic Reference
Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Fuel System Description (See: Powertrain Management/Computers and Control Systems/Description and Operation/Fuel System Description)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1759
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1759
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions)provides an overview of each diagnostic category.
DTC Descriptor
DTC P0016
- Crankshaft Position (CKP) Camshaft Position (CMP) Correlation
Circuit/System Description
The engine control module (ECM) uses the crankshaft position (CKP) sensor and the camshaft position (CMP) sensor pulses to monitor the
correlation between the crankshaft and the camshaft position. The crankshaft reluctor wheel consists of a 60-tooth pattern with 2 teeth missing for
the reference gap. Each tooth is evenly spaced 6 degrees apart, except for the reference gap. The camshaft reluctor wheel has 4 teeth, 2 narrow, and
2 wide. The 4 trailing edges of each tooth are evenly spaced at 90 degrees apart around the circumference of the camshaft sprocket. With the engine
running, and the CMP actuator in the parked position, the ECM expects the camshaft signal pulses to occur 36 crankshaft degrees before top dead
center (BTDC) for cylinder number 1, and every 90 degrees thereafter.
Conditions for Running the DTC
* DTC P0335, P0336, P0340, P0341, P0641, or P0651 is not set.
* The engine is running.
* The engine speed is less than 2,000 RPM.
* DTC P0016 runs continuously when the above conditions are met.
Conditions for Setting the DTC
The ECM detects that the CMP sensor pulses occur more than 11 crank degrees before, or 11 crank degrees after, nominal position for 24 out of 30
engine cycles.
Action Taken When the DTC Sets
DTC P0016 is a Type B DTC.
Conditions for Clearing the DTC
DTC P0016 is a Type B DTC.
Reference Information
Schematic Reference
Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Electronic Ignition System Description (See: Powertrain Management/Computers and Control Systems/Description and Operation/Electronic
Ignition System Description)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning)for scan tool information
Circuit/System Verification
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions)provides an overview of each diagnostic category.
DTC Descriptor
DTC P0016
- Crankshaft Position (CKP) Camshaft Position (CMP) Correlation
Circuit/System Description
The engine control module (ECM) uses the crankshaft position (CKP) sensor and the camshaft position (CMP) sensor pulses to monitor the
correlation between the crankshaft and the camshaft position. The crankshaft reluctor wheel consists of a 60-tooth pattern with 2 teeth missing for
the reference gap. Each tooth is evenly spaced 6 degrees apart, except for the reference gap. The camshaft reluctor wheel has 4 teeth, 2 narrow, and
2 wide. The 4 trailing edges of each tooth are evenly spaced at 90 degrees apart around the circumference of the camshaft sprocket. With the engine
running, and the CMP actuator in the parked position, the ECM expects the camshaft signal pulses to occur 36 crankshaft degrees before top dead
center (BTDC) for cylinder number 1, and every 90 degrees thereafter.
Conditions for Running the DTC
* DTC P0335, P0336, P0340, P0341, P0641, or P0651 is not set.
* The engine is running.
* The engine speed is less than 2,000 RPM.
* DTC P0016 runs continuously when the above conditions are met.
Conditions for Setting the DTC
The ECM detects that the CMP sensor pulses occur more than 11 crank degrees before, or 11 crank degrees after, nominal position for 24 out of 30
engine cycles.
Action Taken When the DTC Sets
DTC P0016 is a Type B DTC.
Conditions for Clearing the DTC
DTC P0016 is a Type B DTC.
Reference Information
Schematic Reference
Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Electronic Ignition System Description (See: Powertrain Management/Computers and Control Systems/Description and Operation/Electronic
Ignition System Description)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning)for scan tool information
Circuit/System Verification
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 591
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 591
Dealer Installed
DTC B2425 or B2430 (Dealer Installed)
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC B2425 04
- Left Seat Heater Cushion Circuit Open
DTC B2425 0A
- Left Seat Heater Cushion Circuit Rate of Change Below Threshold
DTC B2425 0B
- Left Seat Heater Cushion Circuit Current Above Threshold
DTC B2425 0C
- Left Seat Heater Cushion Circuit Current Below Threshold
DTC B2425 0D
- Left Seat Heater Cushion Circuit Resistance Above Threshold
DTC B2425 0E
- Left Seat Heater Cushion Circuit Resistance Below Threshold
DTC B2425 1F
- Left Seat Heater Cushion Circuit Intermittent
DTC B2430 04
- Right Seat Heater Cushion Circuit Open
DTC B2430 0A
- Right Seat Heater Cushion Circuit Rate of Change Below Threshold
DTC B2430 0B
- Right Seat Heater Cushion Circuit Current Above Threshold
DTC B2430 0C
- Right Seat Heater Cushion Circuit Current Below Threshold
DTC B2430 0D
- Right Seat Heater Cushion Circuit Resistance Above Threshold
DTC B2430 0E
- Right Seat Heater Cushion Circuit Resistance Below Threshold
DTC B2430 1F
- Right Seat Heater Cushion Circuit Intermittent
Diagnostic Fault Information
Dealer Installed
DTC B2425 or B2430 (Dealer Installed)
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC B2425 04
- Left Seat Heater Cushion Circuit Open
DTC B2425 0A
- Left Seat Heater Cushion Circuit Rate of Change Below Threshold
DTC B2425 0B
- Left Seat Heater Cushion Circuit Current Above Threshold
DTC B2425 0C
- Left Seat Heater Cushion Circuit Current Below Threshold
DTC B2425 0D
- Left Seat Heater Cushion Circuit Resistance Above Threshold
DTC B2425 0E
- Left Seat Heater Cushion Circuit Resistance Below Threshold
DTC B2425 1F
- Left Seat Heater Cushion Circuit Intermittent
DTC B2430 04
- Right Seat Heater Cushion Circuit Open
DTC B2430 0A
- Right Seat Heater Cushion Circuit Rate of Change Below Threshold
DTC B2430 0B
- Right Seat Heater Cushion Circuit Current Above Threshold
DTC B2430 0C
- Right Seat Heater Cushion Circuit Current Below Threshold
DTC B2430 0D
- Right Seat Heater Cushion Circuit Resistance Above Threshold
DTC B2430 0E
- Right Seat Heater Cushion Circuit Resistance Below Threshold
DTC B2430 1F
- Right Seat Heater Cushion Circuit Intermittent
Diagnostic Fault Information
Subscribe to:
Posts (Atom)