2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 2979

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 2979

Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle) for DTC P254F.

Note: DTC P3401, P3425, P3441, and P3449 sets with an open ignition circuit fuse.

3. Ignition ON, command the appropriate cylinder deactivation solenoid ON and OFF while observing the following status parameters with a

scan tool:

* Cyl. 1, 4, 6, or 7 Deact. Sol. CKT Open Test Status

* Cyl. 1, 4, 6, or 7 Deact. Sol. CKT Short Gnd Test Status

* Cyl. 1, 4, 6, or 7 Deact. Sol. CKT Short Volts Test Status

Each parameter should display OK or Not Run

4. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Ignition OFF, remove the intake manifold. Refer to Intake Manifold Replacement (See: Engine, Cooling and Exhaust/Engine/Intake

Manifold/Service and Repair).

2. Disconnect the harness connector at the valve lifter oil manifold assembly.

3. Ignition ON, verify that a test lamp illuminates between the ignition circuit terminal E and ground.

瀚慖f the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit tests normal and

the ignition circuit fuse is open, test all the components connected to the ignition circuit and replace as necessary.

4. Verify that a test lamp does not illuminate between the ignition circuit terminal E and the appropriate cylinder deactivation solenoid control

circuit terminal listed below.

* Cylinder deactivation solenoid valve 1 terminal C

* Cylinder deactivation solenoid valve 2 terminal A

* Cylinder deactivation solenoid valve 3 terminal B

* Cylinder deactivation solenoid valve 4 terminal D

瀚慖f the test lamp illuminates, test the control circuit for a short to ground. If the circuit tests normal, replace the ECM.

5. Remove the test lamp.

6. Command the appropriate cylinder deactivation solenoid ON with a scan tool. Verify the scan tool Cylinder Deactivation Solenoid Valve

Control Circuit High Voltage Test Status parameter displays OK.

瀚慖f not the specified value, test the appropriate control circuit listed below for a short to voltage. If the circuit tests normal, replace the

ECM.

* Cylinder deactivation solenoid valve 1 terminal C

* Cylinder deactivation solenoid valve 2 terminal A

* Cylinder deactivation solenoid valve 3 terminal B

* Cylinder deactivation solenoid valve 4 terminal D

7. Install a 3 A fused jumper wire between the appropriate control circuit terminal listed below and the ignition circuit terminal E. Command the

appropriate cylinder deactivation solenoid ON with a scan tool. Verify the scan tool Cylinder Deactivation Solenoid Valve Control Circuit

High Voltage Test Status parameter displays Malfunction.

* Cylinder deactivation solenoid valve 1 terminal C

* Cylinder deactivation solenoid valve 2 terminal A

* Cylinder deactivation solenoid valve 3 terminal B

* Cylinder deactivation solenoid valve 4 terminal D

瀚慖f not the specified value, test the control circuit for an open/high resistance. If the circuit tests normal, replace the ECM.

8. If all the circuits test normal, test or replace the valve lifter oil manifold assembly.

Component Testing

Static Test

1. Ignition OFF, open the hood to disable the Auto-Stop function. Refer to Hybrid Modes of Operation Description ( See: Hybrid Drive

Systems/Description and Operation/Hybrid Modes of Operation).

2. Ignition ON, verify the scan tool Hood Position parameter displays Open.

瀚慖f not the specified value, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code

Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle) for DTC P254F.

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 2516

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 2516

Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle) for DTC P254F.

Circuit/System Testing

Note: An intermittent or momentary, less than 1 s, loss of system voltage during throttle tip-in may set DTC P060D.

1. Ignition ON, clear the DTC information with a scan tool. Observe the scan tool DTC information. Verify that DTCs P0602 or P2610 do not

fail this ignition cycle.

瀚慖f DTC P0602 failed this ignition, reprogram the ECM. Refer to Control Module References (See: Testing and Inspection/Programming

and Relearning). If DTC P0602 resets, replace the ECM.

瀚慖f DTC P2610 failed this ignition, test the ECM ignition, battery positive voltage, and ground circuits for an open/high resistance or a

short to ground. If the circuits test normal, replace the ECM.

2. Ignition ON, observe the DTC information with a scan tool. Verify DTCs P0601, P0603, P0604, P0606, P0607, P060D, P062F, or P16F3 do

not set this ignition cycle.

瀚慖f any of the DTCs set this ignition cycle, replace the ECM.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, programming and setup

2ML70 - Automatic Transmission

DTC P0601-P0606, P060B, or P062F

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptor

DTC P0601

- Transmission Control Module (TCM) Read Only Memory (ROM)

DTC P0602

- Transmission Control Module (TCM) Not Programmed

DTC P0603

- Transmission Control Module (TCM) Long Term Memory Reset

DTC P0604

- Transmission Control Module (TCM) Random Access Memory (RAM)

DTC P0606

- Transmission Control Module (TCM) Internal Performance

DTC P060B

- Control Module Analog to Digital Performance

DTC P062F

- Transmission Control Module (TCM) Long Term Memory Performance

Circuit/System Description

This is an internal fault detection of the transmission control module. This fault is handled inside the transmission control module and no external

circuits are involved. The transmission control module is part of the control solenoid valve assembly, and is not serviced separately.

Conditions for Running the DTC

* The control solenoid valve assembly runs the program to detect an internal fault when the key is ON or the engine is running.