2010 Cadillac Truck SRX FWD V6-3.0L Page 1930

2010 Cadillac Truck SRX FWD V6-3.0L Page 1930

2. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Ignition OFF, disconnect the harness connector at the appropriate Q6 Camshaft Position Actuator Solenoid Valve.

2. Ignition ON, verify that a test lamp illuminates between the ignition circuit terminal 1 and ground.

瀚慖f the test lamp does not illuminate, test the circuit for a short to ground or an open/high resistance. If the circuit tests normal and the

ignition circuit fuse is open, test all the components connected to the ignition circuit and replace as necessary.

3. Connect a DMM, set on the diode setting, between the control circuit terminal 2 and ground. The voltage should be greater than 2 V.

瀚慖f the DMM displays OL, test the control circuit for a short to voltage or an open/high resistance. If the circuit/connections test normal,

replace the K20 Engine Control Module.

瀚慖f less than the specified value, test the control circuit for a short to ground. If the circuit tests normal, replace the K20 Engine Control

Module.

4. Command the Camshaft Position Actuator Solenoid Valve ON and OFF with a scan tool. The DMM should transition from greater than 2 V

when commanded OFF to less than 1 V, when commanded ON.

瀚慖f the circuit voltage does not correspond to the specified values, replace the K20 Engine Control Module.

5. If all circuits/connections test normal, test or replace the appropriate Q6 Camshaft Position Actuator Solenoid Valve.

Component Testing

1. Ignition OFF, disconnect the harness connector at the appropriate Q6 Camshaft Position Actuator Solenoid Valve.

2. Test for 7-12 ohm between the control terminal 2 and the ignition terminal 1 of the Q6 Camshaft Position Actuator Solenoid Valve.

瀚慖f not within the specified range, replace the Q6 Camshaft Position Actuator Solenoid Valve.

3. Test for infinite resistance between each terminal and the Q6 Camshaft Position Actuator Solenoid Valve housing.

瀚慖f not the specified value, replace the Q6 Camshaft Position Actuator Solenoid Valve.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Camshaft Position Actuator Solenoid Valve Solenoid Replacement - Bank 1 (Right Side) Intake (See: Engine, Cooling and

Exhaust/Engine/Actuators and Solenoids - Engine/Variable Valve Timing Solenoid/Service and Repair/Camshaft Position Actuator Solenoid

Valve Solenoid Replacement - Bank 1 (Right Side) Intake)

* Camshaft Position Actuator Solenoid Valve Solenoid Replacement - Bank 1 (Right Side) Exhaust (See: Engine, Cooling and

Exhaust/Engine/Actuators and Solenoids - Engine/Variable Valve Timing Solenoid/Service and Repair/Camshaft Position Actuator Solenoid

Valve Solenoid Replacement - Bank 1 (Right Side) Exhaust)

* Camshaft Position Actuator Solenoid Valve Solenoid Replacement - Bank 2 (Left Side) Intake (See: Engine, Cooling and

Exhaust/Engine/Actuators and Solenoids - Engine/Variable Valve Timing Solenoid/Service and Repair/Camshaft Position Actuator Solenoid

Valve Solenoid Replacement - Bank 2 (Left Side) Intake)

* Camshaft Position Actuator Solenoid Valve Solenoid Replacement - Bank 2 (Left Side) Exhaust (See: Engine, Cooling and

Exhaust/Engine/Actuators and Solenoids - Engine/Variable Valve Timing Solenoid/Service and Repair/Camshaft Position Actuator Solenoid

Valve Solenoid Replacement - Bank 2 (Left Side) Exhaust)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for Engine Control Module replacement, setup, and

programming

P2091

DTC P0010, P0013, P0020, P0023, P2088, P2089, P2090, P2091, P2092, P2093, P2094, or P2095 (Without LF1, LFW)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

2010 Cadillac CTS Sedan AWD V6-3.6L Page 1082

2010 Cadillac CTS Sedan AWD V6-3.6L Page 1082

2. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Ignition OFF, disconnect the harness connector at the appropriate HO2S.

2. Ignition ON, verify that the scan tool HO2S 2 voltage parameter is between 400-520 mV.

瀚慖f less than the specified range, test the signal circuit terminal B for a short to ground. If the circuit/connections test normal, replace the

ECM.

瀚慖f greater than the specified range, test the signal circuit terminal B for a short to voltage. If the circuit/connections test normal, replace

the ECM.

3. Connect a 3 A fused jumper wire between the signal circuit terminal B and ground. Verify the scan tool HO2S voltage parameter is less than

60 mV.

瀚慖f greater than the specified range, test the signal circuit for an open/high resistance. If the circuit/connections test normal, replace the

ECM.

4. Connect a 3 A fused jumper wire between the signal circuit terminal B and the low reference circuit terminal A. Verify the scan tool HO2S

voltage parameter is less than 60 mV.

瀚慖f greater than the specified range, test the low reference circuit for an open/high resistance or for a short to voltage. If the

circuit/connections test normal, replace the ECM.

5. Verify that the following conditions do not exist:

* Lean, rich, or leaking fuel injectors.

* A fuel pressure that is too low or too high-Refer to Fuel System Diagnosis (See: Powertrain Management/Computers and Control

Systems/Testing and Inspection/Component Tests and General Diagnostics/Fuel System Diagnosis).

* Fuel that is contaminated-Refer to Alcohol/Contaminants-in-Fuel Diagnosis (with Special Tool) (See: Powertrain

Management/Computers and Control Systems/Testing and Inspection/Component Tests and General

Diagnostics/Alcohol/Contaminants-in-Fuel Diagnosis (with Special Tool))Alcohol/Contaminants-in-Fuel Diagnosis (without Special

Tool) (See: Powertrain Management/Computers and Control Systems/Testing and Inspection/Component Tests and General

Diagnostics/Alcohol/Contaminants-in-Fuel Diagnosis (without Special Tool)).

* Evidence of water intrusion into the electrical connector of the HO2S

* The HO2S is loose

* Exhaust leaks near the HO2S

* Engine vacuum leaks

瀚慖f you find any of the above conditions, repair as necessary.

6. If all circuits/connections test normal, replace the appropriate HO2S sensor.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 (LF1) (See: Powertrain Management/Computers and Control Systems/Oxygen

Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 (LLT) (See: Powertrain Management/Computers and

Control Systems/Oxygen Sensor/Service and Repair)

* Heated Oxygen Sensor Replacement - Bank 2 Sensor 2 (LF1) (See: Powertrain Management/Computers and Control Systems/Oxygen

Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 2 Sensor 2 (LLT) (See: Powertrain Management/Computers and

Control Systems/Oxygen Sensor/Service and Repair)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for engine control module replacement, setup, and

programming

P0140

DTC P0137, P0138, P0140, P0157, P0158, or P0160 (With LLT)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1808

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1808

2. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Ignition OFF, disconnect the harness connector at the appropriate Q6 Camshaft Position Actuator Solenoid Valve.

2. Ignition ON, verify that a test lamp illuminates between the ignition circuit terminal 1 and ground.

瀚慖f the test lamp does not illuminate, test the circuit for a short to ground or an open/high resistance. If the circuit tests normal and the

ignition circuit fuse is open, test all the components connected to the ignition circuit and replace as necessary.

3. Connect a DMM, set on the diode setting, between the control circuit terminal 2 and ground. The voltage should be greater than 2 V.

瀚慖f the DMM displays OL, test the control circuit for a short to voltage or an open/high resistance. If the circuit/connections test normal,

replace the K20 Engine Control Module.

瀚慖f less than the specified value, test the control circuit for a short to ground. If the circuit tests normal, replace the K20 Engine Control

Module.

4. Command the Camshaft Position Actuator Solenoid Valve ON and OFF with a scan tool. The DMM should transition from greater than 2 V

when commanded OFF to less than 1 V, when commanded ON.

瀚慖f the circuit voltage does not correspond to the specified values, replace the K20 Engine Control Module.

5. If all circuits/connections test normal, test or replace the appropriate Q6 Camshaft Position Actuator Solenoid Valve.

Component Testing

1. Ignition OFF, disconnect the harness connector at the appropriate Q6 Camshaft Position Actuator Solenoid Valve.

2. Test for 7-12 ohm between the control terminal 2 and the ignition terminal 1 of the Q6 Camshaft Position Actuator Solenoid Valve.

瀚慖f not within the specified range, replace the Q6 Camshaft Position Actuator Solenoid Valve.

3. Test for infinite resistance between each terminal and the Q6 Camshaft Position Actuator Solenoid Valve housing.

瀚慖f not the specified value, replace the Q6 Camshaft Position Actuator Solenoid Valve.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Camshaft Position Actuator Solenoid Valve Solenoid Replacement - Bank 1 (Right Side) Intake (See: Engine, Cooling and

Exhaust/Engine/Actuators and Solenoids - Engine/Variable Valve Timing Solenoid/Service and Repair/Camshaft Position Actuator Solenoid

Valve Solenoid Replacement - Bank 1 (Right Side) Intake)

* Camshaft Position Actuator Solenoid Valve Solenoid Replacement - Bank 1 (Right Side) Exhaust (See: Engine, Cooling and

Exhaust/Engine/Actuators and Solenoids - Engine/Variable Valve Timing Solenoid/Service and Repair/Camshaft Position Actuator Solenoid

Valve Solenoid Replacement - Bank 1 (Right Side) Exhaust)

* Camshaft Position Actuator Solenoid Valve Solenoid Replacement - Bank 2 (Left Side) Intake (See: Engine, Cooling and

Exhaust/Engine/Actuators and Solenoids - Engine/Variable Valve Timing Solenoid/Service and Repair/Camshaft Position Actuator Solenoid

Valve Solenoid Replacement - Bank 2 (Left Side) Intake)

* Camshaft Position Actuator Solenoid Valve Solenoid Replacement - Bank 2 (Left Side) Exhaust (See: Engine, Cooling and

Exhaust/Engine/Actuators and Solenoids - Engine/Variable Valve Timing Solenoid/Service and Repair/Camshaft Position Actuator Solenoid

Valve Solenoid Replacement - Bank 2 (Left Side) Exhaust)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for Engine Control Module replacement, setup, and

programming

P2096

DTC P2096

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.