2010 Cadillac CTS Sedan AWD V6-3.6L Page 1082
2. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the
conditions that you observed from the Freeze Frame/Failure Records data.
Circuit/System Testing
1. Ignition OFF, disconnect the harness connector at the appropriate HO2S.
2. Ignition ON, verify that the scan tool HO2S 2 voltage parameter is between 400-520 mV.
瀚慖f less than the specified range, test the signal circuit terminal B for a short to ground. If the circuit/connections test normal, replace the
ECM.
瀚慖f greater than the specified range, test the signal circuit terminal B for a short to voltage. If the circuit/connections test normal, replace
the ECM.
3. Connect a 3 A fused jumper wire between the signal circuit terminal B and ground. Verify the scan tool HO2S voltage parameter is less than
60 mV.
瀚慖f greater than the specified range, test the signal circuit for an open/high resistance. If the circuit/connections test normal, replace the
ECM.
4. Connect a 3 A fused jumper wire between the signal circuit terminal B and the low reference circuit terminal A. Verify the scan tool HO2S
voltage parameter is less than 60 mV.
瀚慖f greater than the specified range, test the low reference circuit for an open/high resistance or for a short to voltage. If the
circuit/connections test normal, replace the ECM.
5. Verify that the following conditions do not exist:
* Lean, rich, or leaking fuel injectors.
* A fuel pressure that is too low or too high-Refer to Fuel System Diagnosis (See: Powertrain Management/Computers and Control
Systems/Testing and Inspection/Component Tests and General Diagnostics/Fuel System Diagnosis).
* Fuel that is contaminated-Refer to Alcohol/Contaminants-in-Fuel Diagnosis (with Special Tool) (See: Powertrain
Management/Computers and Control Systems/Testing and Inspection/Component Tests and General
Diagnostics/Alcohol/Contaminants-in-Fuel Diagnosis (with Special Tool))Alcohol/Contaminants-in-Fuel Diagnosis (without Special
Tool) (See: Powertrain Management/Computers and Control Systems/Testing and Inspection/Component Tests and General
Diagnostics/Alcohol/Contaminants-in-Fuel Diagnosis (without Special Tool)).
* Evidence of water intrusion into the electrical connector of the HO2S
* The HO2S is loose
* Exhaust leaks near the HO2S
* Engine vacuum leaks
瀚慖f you find any of the above conditions, repair as necessary.
6. If all circuits/connections test normal, replace the appropriate HO2S sensor.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 (LF1) (See: Powertrain Management/Computers and Control Systems/Oxygen
Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 (LLT) (See: Powertrain Management/Computers and
Control Systems/Oxygen Sensor/Service and Repair)
* Heated Oxygen Sensor Replacement - Bank 2 Sensor 2 (LF1) (See: Powertrain Management/Computers and Control Systems/Oxygen
Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 2 Sensor 2 (LLT) (See: Powertrain Management/Computers and
Control Systems/Oxygen Sensor/Service and Repair)
* Control Module References (See: Testing and Inspection/Programming and Relearning) for engine control module replacement, setup, and
programming
P0140
DTC P0137, P0138, P0140, P0157, P0158, or P0160 (With LLT)
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
