2010 Cadillac Truck SRX FWD V6-3.0L Page 1729

2010 Cadillac Truck SRX FWD V6-3.0L Page 1729

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

Note: If other DTCs are set, diagnose those DTCs first.

1. Perform the Transmission Fluid Level and Condition Check (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing

and Inspection/Component Tests and General Diagnostics/6T70/6T75 - Automatic Transmission/Transmission Fluid Level and Condition

Check) to verify correct fluid level and condition.

Note: Perform a scan tool snapshot during the road test.

2. Perform the Road Test (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing and Inspection/Initial Inspection and

Diagnostic Overview). Verify the transmission operation performs as indicated, in the road test instructions.

3. Review the scan tool snapshot transmission data parameters. Verify the engine and transmission data parameters display the correct values in

all forward gear ranges:

* Engine Speed

* Transmission ISS

* Transmission OSS

* Vehicle Speed

* Shift Solenoid 1

* TFP Switch 1

* TFP Switch 3

* TFP Switch 4

* TFP Switch 5

4. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Perform the Line Pressure Check (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing and Inspection/Component

Tests and General Diagnostics/6T70/6T75 - Automatic Transmission/Line Pressure Check). Verify the transmission line pressure gauge is

within the range specified in the Line PC Solenoid Valve Pressure table. Refer to Solenoid Valve Pressure (See: Specifications/Mechanical

Specifications/Automatic Transmission/Transaxle/System Specifications/6T70/6T75 - Automatic Transmission/Solenoid Valve Pressure).

瀚慖f not within the specified range, repair as necessary. Refer to Fluid Pressure High or Low (See: Transmission and Drivetrain/Automatic

Transmission/Transaxle/Testing and Inspection/Symptom Related Diagnostic Procedures/6T70/6T75 - Automatic Transmission/Fluid

Pressure High or Low) for further diagnosis.

2. Ignition OFF, remove the control solenoid valve assembly. Refer to Control Solenoid Valve and Transmission Control Module Assembly

Replacement (See: Powertrain Management/Transmission Control Systems/Actuators and Solenoids - Transmission and

Drivetrain/Actuators and Solenoids - A/T/Shift Solenoid/Service and Repair).

3. Perform the Control Solenoid Valve and Transmission Control Module Assembly Solenoid Performance Test (See: Transmission and

Drivetrain/Automatic Transmission/Transaxle/Testing and Inspection/Component Tests and General Diagnostics/6T70/6T75 - Automatic

Transmission/Control Solenoid Valve and Transmission Control Module Assembly Solenoid Performance Test). Test all solenoids on the

control solenoid valve assembly. A pressure change should occur for each solenoid.

瀚慖f the control solenoid valve assembly does not pass the performance test, replace the control solenoid valve assembly.

4. Listed in the table below are conditions for each component that could set DTC P0751 or P0752. Carefully inspect each component for that

condition. Repair or replace as necessary.

2010 Cadillac Truck SRX FWD V6-3.0L Page 1578

2010 Cadillac Truck SRX FWD V6-3.0L Page 1578

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Circuit/System Verification

Note: This DTC may be stored as a history DTC without affecting the operation of the module. If stored only as a history DTC and not retrieved as

a current DTC, do not replace the module.

Verify that DTC P0602 is not set.

If the DTC is set, program the K27 fuel pump control module.

Verify that DTCs P0601, P0603, P0604, P0606, and P062F are not set.

If the DTCs are set, program the K27 fuel pump control module. If the DTCs reset, replace the K27 fuel pump control module.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

Control Module References (See: Testing and Inspection/Programming and Relearning) for fuel pump control module replacement, setup, and

programming

6T70/6T75 - Automatic Transmission

DTC P0601-P0604 or P062F

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC P0601

- Transmission Control Module (TCM) Read Only Memory (ROM)

DTC P0602

- Transmission Control Module (TCM) Not Programmed

DTC P0603

- Transmission Control Module (TCM) Long Term Memory Reset

DTC P0604

- Transmission Control Module (TCM) Random Access Memory (RAM)

DTC P062F

- Transmission Control Module (TCM) Long Term Memory Performance

Circuit/System Description

This is an internal fault detection of the control solenoid (w/body and TCM) valve assembly. This fault is handled inside the control solenoid

(w/body and TCM) valve assembly and no external circuits are involved.

Conditions for Running the DTC

The ignition is ON.

Conditions for Setting the DTC

2010 Cadillac Truck SRX FWD V6-3.0L Page 2035

2010 Cadillac Truck SRX FWD V6-3.0L Page 2035

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

* Heated Oxygen Sensor Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical

Diagnostic Procedures/Wiring Repairs/Heated Oxygen Sensor Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

1. Ignition ON, observe the DTC information with a scan tool. Verify no B52 HO2S heater DTCs are set.

瀚慖f a B52 HO2S heater DTC is set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code

Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle).

2. Engine running, observe the appropriate scan tool B52 HO2S voltage parameter. The reading should be within the range of 50-1,050 mV.

3. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Ignition OFF, disconnect the appropriate B52 HO2S harness connector.

2. Ignition ON, observe the appropriate scan tool HO2S voltage parameter. The parameter should display 1.27 V.

瀚慖f less than the specified range, test the high and low signal circuits for a short to ground. If both signal circuit test normal, replace the

K20 ECM.

3. Ignition ON, test for 2.5-3.0 V between the high signal circuit terminal B and ground.

瀚慖f less than the specified range, test the high signal circuit for an open/high resistance. If the circuit tests normal, replace the K20 ECM.

瀚慖f greater than the specified range, test the high signal circuit for a short to voltage. If the circuit tests normal, replace the K20 ECM.

4. Ignition OFF, connect a 3 A fused jumper wire between the high signal circuit terminal B and the low signal circuit terminal A.

Note: The low signal circuit is tied to a pull-up circuit within the ECM. A voltage of 0.90-1.10 V on the low signal circuit is normal.

5. Ignition ON, verify the scan tool HO2S parameter displays 0.0 V.

瀚慖f greater than the specified range, test the low signal circuit for an open/high resistance or for a short to voltage. If the circuit tests

normal, replace the K20 ECM.

6. If all circuits test normal, test or replace the appropriate B52 HO2S.

Repair Instructions

Caution: Refer to Heated Oxygen Sensor Resistance Learn Reset Caution (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service Precautions/Heated Oxygen Sensor Resistance Learn Reset Caution).

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Heated Oxygen Sensor Replacement - Bank 1 Sensor 2 (LF1) (See: Powertrain Management/Computers and Control Systems/Oxygen

Sensor/Service and Repair/Heated Oxygen Sensor Replacement - Bank 1 Sensor 2)

* Heated Oxygen Sensor Replacement - Bank 2 Sensor 2 (LF1) (See: Powertrain Management/Computers and Control Systems/Oxygen

Sensor/Service and Repair/Heated Oxygen Sensor Replacement - Bank 2 Sensor 2)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming

P2273

DTC P2271 or P2273 (LF1)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 3001

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 3001

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Testing

1. Ignition OFF, disconnect the harness connector of the yaw rate sensor.

2. Ignition ON, verify that a test lamp illuminates between the module voltage circuit and ground.

瀚慖f the test lamp does not illuminate, test the circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the

EBCM.

3. Ignition OFF, test for less than 5 ohms between the module ground circuits and ground.

瀚慖f greater than the specified value, test the ground circuit for an open/high resistance. If the circuit tests normal, replace the EBCM.

4. If all circuits test normal, replace the yaw rate sensor.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* GMLAN Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Wiring Repairs/GMLAN Wiring Repairs)

* ABS Description and Operation (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Description and

Operation/ABS Description and Operation) for the ABS - Hybrid

* Vehicle Yaw Sensor with Vehicle Lateral Accelerometer Replacement (See: Brakes and Traction Control/Antilock Brakes / Traction

Control Systems/Yaw Rate Sensor/Service and Repair/Less than 3900 kg (8600 lb) GVW) for the ABS - Non-Hybrid Less than 3900 kg

(8600 lb) GVW

* Vehicle Yaw Sensor with Vehicle Lateral Accelerometer Replacement (See: Brakes and Traction Control/Antilock Brakes / Traction

Control Systems/Yaw Rate Sensor/Service and Repair/Less than 3900 kg (8600 lb) GVW) for the ABS - Non-Hybrid Greater than/Equal to

3900 kg (8600 lb) GVW

* Control Module References (See: Testing and Inspection/Programming and Relearning) for module replacement, setup, and programming

U2161

DTC U2105-U2199

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptor

DTC U2142 00

- Lost Communication With Yaw Rate Sensor (YRS)

Circuit/System Description

Modules connected to the CAN bus serial data circuits monitor for serial data communications during normal vehicle operation. Operating

information and commands are exchanged among the modules. The modules have prerecorded information about what messages are needed to be

exchanged on the serial data circuits. The messages are supervised and also, some periodic messages are used by the receiver module as an

availability indication of the transmitter module. Each message contains the identification number of the transmitter module.

The electronic brake control module (EBCM) activates the other modules connected to the CAN serial data circuits by applying voltage when the

ignition key is in ACC, ON or START. The EBCM, Yaw Rate and Lateral Acceleration Sensor are the only modules connected to the CAN bus

serial data circuits. For more information on CAN bus serial data refer to Data Link Communications Description and Operation (See: Powertrain

Management/Computers and Control Systems/Information Bus/Description and Operation).

Conditions for Running the DTC

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2944

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2944

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Testing

1. Ignition OFF, disconnect the harness connector of the yaw rate sensor.

2. Ignition ON, verify that a test lamp illuminates between the module voltage circuit and ground.

瀚慖f the test lamp does not illuminate, test the circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the

EBCM.

3. Ignition OFF, test for less than 5 ohms between the module ground circuits and ground.

瀚慖f greater than the specified value, test the ground circuit for an open/high resistance. If the circuit tests normal, replace the EBCM.

4. If all circuits test normal, replace the yaw rate sensor.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* GMLAN Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Wiring Repairs/GMLAN Wiring Repairs)

* ABS Description and Operation (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Description and

Operation/ABS Description and Operation) for the ABS - Hybrid

* Vehicle Yaw Sensor with Vehicle Lateral Accelerometer Replacement (See: Brakes and Traction Control/Antilock Brakes / Traction

Control Systems/Yaw Rate Sensor/Service and Repair/Less than 3900 kg (8600 lb) GVW) for the ABS - Non-Hybrid Less than 3900 kg

(8600 lb) GVW

* Vehicle Yaw Sensor with Vehicle Lateral Accelerometer Replacement (See: Brakes and Traction Control/Antilock Brakes / Traction

Control Systems/Yaw Rate Sensor/Service and Repair/Less than 3900 kg (8600 lb) GVW) for the ABS - Non-Hybrid Greater than/Equal to

3900 kg (8600 lb) GVW

* Control Module References (See: Testing and Inspection/Programming and Relearning) for module replacement, setup, and programming

U2133

DTC U2105-U2199

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptor

DTC U2142 00

- Lost Communication With Yaw Rate Sensor (YRS)

Circuit/System Description

Modules connected to the CAN bus serial data circuits monitor for serial data communications during normal vehicle operation. Operating

information and commands are exchanged among the modules. The modules have prerecorded information about what messages are needed to be

exchanged on the serial data circuits. The messages are supervised and also, some periodic messages are used by the receiver module as an

availability indication of the transmitter module. Each message contains the identification number of the transmitter module.

The electronic brake control module (EBCM) activates the other modules connected to the CAN serial data circuits by applying voltage when the

ignition key is in ACC, ON or START. The EBCM, Yaw Rate and Lateral Acceleration Sensor are the only modules connected to the CAN bus

serial data circuits. For more information on CAN bus serial data refer to Data Link Communications Description and Operation (See: Powertrain

Management/Computers and Control Systems/Information Bus/Description and Operation).

Conditions for Running the DTC

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2610

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2610

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Special Tools

EN-46999 Displacement On Demand Tester

For equivalent regional tools, refer to Special Tools (See: Powertrain Management/Computers and Control Systems/Tools and Equipment).

Circuit/System Verification

Note: DTC P3401, P3425, P3441, and P3449 sets with an open ignition circuit fuse.

1. Ignition ON, command the appropriate cylinder deactivation solenoid ON and OFF while observing the following status parameters with a

scan tool:

* Cyl. 1, 4, 6, or 7 Deact. Sol. Ckt Open Test Status

* Cyl. 1, 4, 6, or 7 Deact. Sol. Ckt Short Gnd Test Status

* Cyl. 1, 4, 6, or 7 Deact. Sol. Ckt Short Volts Test Status

Each parameter should display OK or Not Run

2. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Ignition OFF, remove the intake manifold. Refer to Intake Manifold Replacement (Without AFM) (See: Engine, Cooling and

Exhaust/Engine/Intake Manifold/Service and Repair)Intake Manifold Replacement (With AFM) (See: Engine, Cooling and

Exhaust/Engine/Intake Manifold/Service and Repair).

2. Disconnect the harness connector at the valve lifter oil manifold assembly.

3. Ignition ON, verify that a test lamp illuminates between the ignition circuit terminal E and ground.

瀚慖f the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit tests normal and

the ignition circuit fuse is open, test all the components connected to the ignition circuit and replace as necessary.

4. Verify that a test lamp does not illuminate between the ignition circuit terminal E and the appropriate cylinder deactivation solenoid control

circuit terminal listed below.

* Cylinder deactivation solenoid valve 1 terminal C

* Cylinder deactivation solenoid valve 2 terminal A

* Cylinder deactivation solenoid valve 3 terminal B

* Cylinder deactivation solenoid valve 4 terminal D

瀚慖f the test lamp illuminates, test the control circuit for a short to ground. If the circuit tests normal, replace the ECM.

5. Remove the test lamp.

6. Command the appropriate cylinder deactivation solenoid ON with a scan tool. Verify the scan tool Cylinder Deactivation Solenoid Valve

Control Circuit High Voltage Test Status parameter displays OK.

瀚慖f not the specified value, test the appropriate control circuit listed below for a short to voltage. If the circuit tests normal, replace the

ECM.

* Cylinder deactivation solenoid valve 1 terminal C

* Cylinder deactivation solenoid valve 2 terminal A

* Cylinder deactivation solenoid valve 3 terminal B

* Cylinder deactivation solenoid valve 4 terminal D

7. Install a 3 A fused jumper wire between the appropriate control circuit terminal listed below and the ignition circuit terminal E. Command the

appropriate cylinder deactivation solenoid ON with a scan tool. Verify the scan tool Cylinder Deactivation Solenoid Valve Control Circuit

High Voltage Test Status parameter displays Malfunction.

* Cylinder deactivation solenoid valve 1 terminal C

* Cylinder deactivation solenoid valve 2 terminal A

2010 Cadillac Truck SRX AWD V6-3.0L Page 385

2010 Cadillac Truck SRX AWD V6-3.0L Page 385

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

Measure actual temperature using a thermometer at each of the duct temperature sensors. Compare this value to the appropriate scan tool Duct

Actual parameter. The measured temperature should be within 5掳C (9掳F) difference of appropriate Duct Actual parameter value.

Circuit/System Testing

1. Ignition OFF, disconnect the harness connector at the appropriate temperature sensor.

2. Test for less than 10 ohm between the temperature sensor ground circuit terminal B and ground.

瀚慖f greater than the specified value, test the ground circuit for an open/high resistance. If the circuit tests normal, replace the K33 HVAC

Control Module.

3. Ignition ON, test for 4.8-5.2 V between the signal circuit terminal A and ground.

瀚慖f less than the specified range, test the signal circuit for a short to ground or open/high resistance. If the circuit tests normal, replace the

K33 HVAC Control Module.

瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the K33 HVAC Control

Module.

4. If all circuits test normal, replace the temperature sensor.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* HVAC Component Replacement Reference (See: Heating and Air Conditioning/Service and Repair/Removal and Replacement)

* Control Module References (See: Testing and Inspection/Programming and Relearning)

B0550

DTC B0550

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptor

DTC B0550 32

- Odometer Circuit General Memory Malfunction

Circuit/System Description

The instrument cluster is equipped with odometers that indicate the distance traveled by the vehicle. One type of odometer is the season odometer

where the traveled distance can not be reset by the driver. This information is also stored in the body control module (BCM). In addition to storing

the season odometer value for the vehicle, the instrument cluster and the BCM store the VIN. Software checks are performed to ensure these

modules, and their stored season odometer information, can not be moved or transferred between different vehicles.

Conditions for Running the DTC

The ignition is ON.

Conditions for Setting the DTC

The BCM has detected an internal memory malfunction.

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2215

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2215

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

Circuit/System Verification

1. Clear the DTC information.

2. Ignition OFF for 1 minute.

3. Ignition ON.

4. Retest for DTCs P0642, P0643, P0652 and P0653.

Circuit/System Testing

1. Clear the DTC and operate the vehicle under the condition for running and setting the DTC.

2. Shut the ignition OFF for 30 seconds, and verify that the DTC does not reset.

瀚慖f the DTC resets, replace the Drive Motor Generator Power Inverter Module Assembly (PIM).

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

Control Module References (See: Testing and Inspection/Programming and Relearning) for PIM replacement, setup, and programming.

P0653

DTC P0642, P0643, P0652, or P0653

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptor

DTC P0642

- 5 Volt Reference 1 Circuit Low Voltage

DTC P0643

- 5 Volt Reference 1 Circuit High Voltage

DTC P0652

- 5 Volt Reference 2 Circuit Low Voltage

DTC P0653

- 5 Volt Reference 2 Circuit High Voltage

Circuit/System Description

The drive motor generator power inverter module (PIM) contains two motor control modules (MCM) and a hybrid powertrain control module

(HPCM). Each MCM utilizes a 5 Volt reference power supply for internal circuit needs. This fault is handled inside the PIM and no external

circuits are involved.

Conditions for Running the DTC

* The control module runs the program to detect an internal fault when the key is ON.

* Ignition voltage is 8-18V.

Conditions for Setting the DTC

The control module has detected an internal malfunction.

Action Taken When the DTC Sets

* DTCs P0642, P0643, P0652 and P0653 are Type A DTCs.

* The PIM commands the battery energy control module (BECM) to open the high voltage contactor relays.

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2175

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2175

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Circuit/System Verification

Note: This DTC may be stored as a history DTC without affecting the operation of the module. If stored only as a history DTC and not retrieved as

a current DTC, do not replace the module.

1. Verify that DTC P0602 is not set.

瀚慖f the DTC is set, program the K27 fuel pump control module.

2. Verify that DTCs P0601, P0603, P0604, P0606, and P062F are not set.

瀚慖f the DTCs are set, program the K27 fuel pump control module. If the DTCs reset, replace the K27 fuel pump control module.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

Control Module References (See: Testing and Inspection/Programming and Relearning)for fuel pump control module replacement, setup, and

programming

2ML70 - Automatic Transmission

DTC P0601-P0606, P060B, or P062F

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptor

DTC P0601

- Transmission Control Module (TCM) Read Only Memory (ROM)

DTC P0602

- Transmission Control Module (TCM) Not Programmed

DTC P0603

- Transmission Control Module (TCM) Long Term Memory Reset

DTC P0604

- Transmission Control Module (TCM) Random Access Memory (RAM)

DTC P0606

- Transmission Control Module (TCM) Internal Performance

DTC P060B

- Control Module Analog to Digital Performance

DTC P062F

- Transmission Control Module (TCM) Long Term Memory Performance

Circuit/System Description

This is an internal fault detection of the transmission control module. This fault is handled inside the transmission control module and no external

circuits are involved. The transmission control module is part of the control solenoid valve assembly, and is not serviced separately.

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2126

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2126

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning)for scan tool information

Circuit/System Testing

1. Engine running, accessories OFF, measure and record the battery voltage at the battery terminals. The voltage should be between 12.6 and

15.0 volts.

瀚慖f not within the specified range, refer to Charging System Test (See: Starting and Charging/Testing and Inspection/Component Tests

and General Diagnostics/Charging System Test).

2. Ignition OFF, disconnect the harness connectors at the ECM.

3. Ignition OFF and scan tool disconnected, open and close the driver door, and wait 1 minute. Test for less than 5 ohms of resistance between

the ground circuit terminal 73 X1 and ground.

瀚慖f greater than the specified range, test the ground circuit for an open/high resistance.

4. Verify that a test lamp illuminates between the B+ circuit terminal 20 X1 and ground.

瀚慖f the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance.

5. Install a 3A jumper wire between the PWR/TRN relay control circuit terminal 59 X1 and ground.

6. Ignition ON, verify that a test lamp illuminates between the ignition circuit terminals listed below and ground.

* Terminal 19 X1

* Terminal 47 X1

瀚慖f the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance.

7. If all circuits test normal, replace the ECM.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

Control Module References (See: Testing and Inspection/Programming and Relearning)for ECM replacement, setup, and programming.

FPCM

DTC P0562 (FPCM)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptor

DTC P0562

- System Voltage Low - FPCM

Diagnostic Fault Information

Circuit/System Description

The fuel pump control module (FPCM) monitors the system voltage to ensure that the voltage stays within the proper range. Damage to

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2011

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2011

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Special Tools

J 35616 GM Approved Terminal Test Kit

Circuit/System Verification

1. Engine at operating temperature, observe DTC information with a scan tool. DTC P0324, P0325, P0326, P0327, P0328, P0330, P0332, or

P0333 should not set.

2. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

P0324

Note: If DTC P0325, P0326, P0327, P0328, P0330, P0332, or P0333 are also set, diagnose those DTCs first.

DTC P0324 indicates an internal control module circuitry failure. Replace the ECM.

P0325, P0326, P0327, P0328, P0330, P0332, P0333

1. Ignition OFF, disconnect the affected KS.

2. Ignition OFF. Connect a DMM to both KS signal circuits, terminals A and B, at the affected KS. Set the DMM to the 400 mV AC scale,

select the Hz mode. Let the reading stabilize at 0 Hz.

Note: DO NOT tap on plastic engine components.

3. Tap on the engine block with a non-metallic object near the affected KS and observe the DMM for a fluctuating frequency.

瀚慖f the DMM does not display a fluctuating frequency while tapping on the engine block then replace the affected KS.

4. Verify the affected KS is properly tightened, refer to Fastener Tightening Specifications (See: Engine, Cooling and

Exhaust/Engine/Specifications/Fastener Tightening Specifications).

5. Ignition OFF, with appropriate length jumper wires, connect the KS1 harness to the KS2 sensor and the KS2 harness to the KS1 sensor.

6. Monitor the DTCs using a scan tool. Operate the vehicle within the conditions for running the DTC. Verify the fault does not follow the

sensor in question.

瀚慖f the fault follows the sensor in question, replace the appropriate KS.

7. Ignition OFF, remove the jumper wires from the previous step.

8. Measure for 2-3 volts between each of the following circuits and ground on the ECM side of the harness connector:

* The KS signal circuit, terminal A

* The KS signal circuit, terminal B

瀚慖f less than the specified range, test the circuits for a short to ground or an open/high resistance. If the circuits test normal, replace the

ECM.

瀚慖f greater than the specified range, test the circuits for a short to voltage. If the circuits test normal, replace the ECM.

9. Test for intermittent or poor connections at the ECM, KS, and in-line connectors where present.

10. If all circuits test normal, replace the ECM.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Knock Sensor 1 Replacement (See: Powertrain Management/Computers and Control Systems/Knock Sensor/Service and Repair/Knock

Sensor 1 Replacement)

* Knock Sensor 2 Replacement (See: Powertrain Management/Computers and Control Systems/Knock Sensor/Service and Repair/Knock

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1925

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1925

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Special Tools

J 34730-405 Injector Test Lamp

Circuit/System Verification

1. Engine idling, observe the following control circuit status parameters for each fuel injector:

* Cyl 1-8 Injector Ckt Short Gnd Test Status

* Cyl 1-8 Injector Ckt Open Test Status

* Cyl 1-8 Injector Ckt Short Volts Test Status

Each parameter should display OK or Not Run.

2. Engine running, observe the DTC information with a scan tool. DTC P0201, P0202, P0203, P0204, P0205, P0206, P0207 or P0208 should

not set.

3. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Ignition OFF, disconnect the affected fuel injector harness connector at the fuel injector.

2. Ignition ON, verify that a test lamp illuminates between the ignition voltage circuit terminal A and ground.

瀚慖f the test lamp does not illuminate, test the ignition voltage circuit for a short to ground or an open/high resistance. If the circuit tests

normal and the ignition voltage circuit fuse is open, test or replace the fuel injector.

3. Connect the J 34730-405 between the control circuit terminal B and the ignition voltage circuit terminal A.

4. Command the fuel injector ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded

states.

瀚慖f the test lamp is always ON, test the control circuit for a short to ground. If the circuit tests normal, replace the engine control module

(ECM).

瀚慖f the test lamp is always OFF, test the control circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace

the ECM.

5. If all circuits test normal, test or replace the fuel injector.

Component Testing

Note: The engine coolant temperature (ECT) sensor must be between 10-32掳C (50-90掳F) for an accurate measurement.

Measure for 11-14 ohm between the terminals of the fuel injector.

If not within the specified range, replace the fuel injector.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Fuel Injector Replacement (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Injector/Service and Repair/Removal and

Replacement)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming

P0204

DTC P0201, P0202, P0203, P0204, P0205, P0206, P0207, or P0208

Diagnostic Instructions

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1830

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1830

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning)for scan tool information

Circuit/System Verification

1. Ignition ON, observe the DTC information with a scan tool. Verify no B52 HO2S heater DTCs are set.

瀚慖f a B52 HO2S heater DTC is set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code

Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle).

2. Engine running, observe the appropriate scan tool B52 HO2S voltage parameter. The reading should be within the range of 50-1,050 mV.

3. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

Note: All modules must be powered down or misdiagnosis may result.

1. Ignition OFF, disconnect the harness connector at the appropriate B52 HO2S.

2. Ignition OFF, all vehicle systems OFF, this may take up to 2 minutes, test for less than 5 ohm between the low reference circuit terminal A

and ground.

瀚慖f greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the ECM.

3. Ignition ON, verify the appropriate scan tool B52 HO2S parameter is approximately 450 mV.

瀚慖f less than the specified value, test the signal circuit for a short to ground. If the circuit tests normal, replace the K20 ECM.

瀚慖f greater than the specified value, test the signal circuit for a short to voltage. If the circuit tests normal, replace the K20 ECM.

4. Ignition ON, install a 3 A fused jumper wire between the signal circuit terminal B and ground. Verify the appropriate scan tool B52 HO2S

parameter is less than 60 mV.

瀚慖f greater than the specified range, test the signal circuit for an open/high resistance. If the circuit tests normal, replace the K20 ECM.

5. If all circuits test normal, replace the appropriate B52 HO2S.

Repair Instructions

Caution: Refer to Heated Oxygen Sensor Resistance Learn Reset Caution (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service Precautions/Heated Oxygen Sensor Resistance Learn Reset Caution).

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 (1500 Series) (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 (2500 Series) (See: Powertrain

Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)

* Heated Oxygen Sensor Replacement - Bank 1 Sensor 2 (1500 Series) (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 1 Sensor 2 (2500 Series) (See: Powertrain

Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)

* Heated Oxygen Sensor Replacement - Bank 2 Sensor 1 (1500 Series) (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 2 Sensor 1 (2500 Series) (See: Powertrain

Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)

* Heated Oxygen Sensor Replacement - Bank 2 Sensor 2 (1500 Series) (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 2 Sensor 2 (2500 Series) (See: Powertrain

Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)

* Control Module References (See: Testing and Inspection/Programming and Relearning)for ECM replacement, setup, and programming

P0158

DTC P0131, P0132, P0137, P0138, P0151, P0152, P0157, or P0158

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1621

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1621

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

Note: If a crankshaft or camshaft position sensor DTC is set, the Camshaft Position Actuator output control will not function.

1. Ignition ON, observe the DTC information with a scan tool. Verify DTC P0335, P0336, P0340, and P0341 is not set.

瀚慖f a DTC is set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code Descriptions/Diagnostic Trouble

Code (DTC) List - Vehicle) for further diagnosis.

2. Engine idling, command the Camshaft Position Actuator to 10掳 while observing the following control circuit status parameters with a scan

tool:

* The CMP Actuator Solenoid Ckt Short To Ground Test Status

* The CMP Acutator Solenoid Ckt Open Test Status

* The CMP Actuator Solenoid Ckt Short To Volts Test Status

Each parameter should display OK or Not Run

3. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Ignition OFF, disconnect the Camshaft Position Sensor and Actuator Magnet jumper harness connector. Refer to Inline Harness Connector

End Views (See: Power and Ground Distribution/Multiple Junction Connector/Diagrams) for connector identification.

Note: Testing for steps 2-4 is performed on the ECM side of the jumper harness connector.

2. Ignition OFF for 1 minute, test for less than 5 ohm between the low reference circuit terminal E and ground.

瀚慖f greater than the specified value, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the ECM.

Note: A test lamp must be used for this test. The control circuit is pulled-up to a low current voltage. A voltage on the control circuit is

normal.

3. Ignition ON, engine OFF, verify that a test lamp does not illuminate between the control circuit terminal D and ground.

瀚慖f the test lamp illuminates, test the control circuit for a short to voltage. If the circuit tests normal, replace the ECM.

4. Connect the DMM black lead to the control circuit terminal D. Connect the DMM red lead to B+. Set the DMM on the diode setting.

Command the CMP actuator solenoid ON and OFF with a scan tool. The DMM should transition from OL when commanded OFF to less

than 1 V when commanded ON.

瀚慖f the circuit voltage does not correspond to the specified values, test the control circuit for an open/high resistance or a short to ground. If

the circuit tests normal, replace the ECM.

Note: Testing for steps 5 and 6 is performed on the engine side of the jumper harness connector.

5. Ignition OFF, test for infinite resistance between the control circuit terminal D and ground.

瀚慖f not the specified value, repair the control circuit for a short to ground.

6. Test for 5.0-9.0 ohm between the control circuit terminal D and the low reference circuit terminal E.

瀚慖f less than the specified range, test for a short between the control circuit and the low reference circuit. If the circuits/connections test

normal, test or replace the Camshaft Position Actuator Magnet.

瀚慖f greater than the specified range, test the control circuit and the low reference for an open/high resistance. If the circuits/connections test

normal, test or replace the Camshaft Position Actuator Magnet.

7. If all circuits test normal, repair the poor connection at the camshaft position sensor jumper wire harness.

2010 Cadillac Truck SRX AWD V6-3.0L Page 522

2010 Cadillac Truck SRX AWD V6-3.0L Page 522

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Testing

1. Ignition OFF, disconnect the X2, X3 harness connectors at the K29 seat heating control module.

2. Test for greater than 3.0 kOhms between the signal and the low reference circuits listed below:

* E14B driver seat cushion terminal 3 X3 and terminal 13 X2

* E14D passenger seat cushion terminal 4 X3 and terminal 14 X2

瀚慖f less than the specified value, test for a short between the signal and low reference circuits. If the circuits test normal, replace the

appropriate E14 seat cushion heating element.

3. If all circuits test normal, replace the K29 seat heating control module.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Driver or Passenger Seat Cushion Heater Replacement (See: Body and Frame/Seats/Seat Temperature Element/Service and Repair/Driver or

Passenger Seat Cushion Heater Replacement)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for seat heating control module replacement, setup

and programming

With KA6

DTC B2345 (With KA6)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC B2345 13

- Seat Heater Disable Circuit Low Voltage High/Temperature

Diagnostic Fault Information

Circuit/System Description

The rear seat heating control module controls seat heating operation for both left and right rear seats. The heating elements are controlled through

individual high side and low side control circuits. The low side control circuits for both seats are connected to a common reference point internal to

2010 Cadillac Truck Escalade RWD V8-6.2L Page 3001

2010 Cadillac Truck Escalade RWD V8-6.2L Page 3001

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Testing

1. Ignition OFF, disconnect the harness connector of the yaw rate sensor.

2. Ignition ON, verify that a test lamp illuminates between the module voltage circuit and ground.

瀚慖f the test lamp does not illuminate, test the circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the

EBCM.

3. Ignition OFF, test for less than 5 ohms between the module ground circuits and ground.

瀚慖f greater than the specified value, test the ground circuit for an open/high resistance. If the circuit tests normal, replace the EBCM.

4. If all circuits test normal, replace the yaw rate sensor.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* GMLAN Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Wiring Repairs/GMLAN Wiring Repairs)

* ABS Description and Operation (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Description and

Operation/ABS Description and Operation) for the ABS - Hybrid

* Vehicle Yaw Sensor with Vehicle Lateral Accelerometer Replacement (See: Brakes and Traction Control/Antilock Brakes / Traction

Control Systems/Yaw Rate Sensor/Service and Repair/Less than 3900 kg (8600 lb) GVW) for the ABS - Non-Hybrid Less than 3900 kg

(8600 lb) GVW

* Vehicle Yaw Sensor with Vehicle Lateral Accelerometer Replacement (See: Brakes and Traction Control/Antilock Brakes / Traction

Control Systems/Yaw Rate Sensor/Service and Repair/Less than 3900 kg (8600 lb) GVW) for the ABS - Non-Hybrid Greater than/Equal to

3900 kg (8600 lb) GVW

* Control Module References (See: Testing and Inspection/Programming and Relearning) for module replacement, setup, and programming

U2161

DTC U2105-U2199

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptor

DTC U2142 00

- Lost Communication With Yaw Rate Sensor (YRS)

Circuit/System Description

Modules connected to the CAN bus serial data circuits monitor for serial data communications during normal vehicle operation. Operating

information and commands are exchanged among the modules. The modules have prerecorded information about what messages are needed to be

exchanged on the serial data circuits. The messages are supervised and also, some periodic messages are used by the receiver module as an

availability indication of the transmitter module. Each message contains the identification number of the transmitter module.

The electronic brake control module (EBCM) activates the other modules connected to the CAN serial data circuits by applying voltage when the

ignition key is in ACC, ON or START. The EBCM, Yaw Rate and Lateral Acceleration Sensor are the only modules connected to the CAN bus

serial data circuits. For more information on CAN bus serial data refer to Data Link Communications Description and Operation (See: Powertrain

Management/Computers and Control Systems/Information Bus/Description and Operation).

Conditions for Running the DTC

2010 Cadillac Truck Escalade RWD V8-6.2L Page 2944

2010 Cadillac Truck Escalade RWD V8-6.2L Page 2944

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Testing

1. Ignition OFF, disconnect the harness connector of the yaw rate sensor.

2. Ignition ON, verify that a test lamp illuminates between the module voltage circuit and ground.

瀚慖f the test lamp does not illuminate, test the circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the

EBCM.

3. Ignition OFF, test for less than 5 ohms between the module ground circuits and ground.

瀚慖f greater than the specified value, test the ground circuit for an open/high resistance. If the circuit tests normal, replace the EBCM.

4. If all circuits test normal, replace the yaw rate sensor.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* GMLAN Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Wiring Repairs/GMLAN Wiring Repairs)

* ABS Description and Operation (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Description and

Operation/ABS Description and Operation) for the ABS - Hybrid

* Vehicle Yaw Sensor with Vehicle Lateral Accelerometer Replacement (See: Brakes and Traction Control/Antilock Brakes / Traction

Control Systems/Yaw Rate Sensor/Service and Repair/Less than 3900 kg (8600 lb) GVW) for the ABS - Non-Hybrid Less than 3900 kg

(8600 lb) GVW

* Vehicle Yaw Sensor with Vehicle Lateral Accelerometer Replacement (See: Brakes and Traction Control/Antilock Brakes / Traction

Control Systems/Yaw Rate Sensor/Service and Repair/Less than 3900 kg (8600 lb) GVW) for the ABS - Non-Hybrid Greater than/Equal to

3900 kg (8600 lb) GVW

* Control Module References (See: Testing and Inspection/Programming and Relearning) for module replacement, setup, and programming

U2133

DTC U2105-U2199

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptor

DTC U2142 00

- Lost Communication With Yaw Rate Sensor (YRS)

Circuit/System Description

Modules connected to the CAN bus serial data circuits monitor for serial data communications during normal vehicle operation. Operating

information and commands are exchanged among the modules. The modules have prerecorded information about what messages are needed to be

exchanged on the serial data circuits. The messages are supervised and also, some periodic messages are used by the receiver module as an

availability indication of the transmitter module. Each message contains the identification number of the transmitter module.

The electronic brake control module (EBCM) activates the other modules connected to the CAN serial data circuits by applying voltage when the

ignition key is in ACC, ON or START. The EBCM, Yaw Rate and Lateral Acceleration Sensor are the only modules connected to the CAN bus

serial data circuits. For more information on CAN bus serial data refer to Data Link Communications Description and Operation (See: Powertrain

Management/Computers and Control Systems/Information Bus/Description and Operation).

Conditions for Running the DTC

2010 Cadillac Truck Escalade RWD V8-6.2L Page 2610

2010 Cadillac Truck Escalade RWD V8-6.2L Page 2610

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Special Tools

EN-46999 Displacement On Demand Tester

For equivalent regional tools, refer to Special Tools (See: Powertrain Management/Computers and Control Systems/Tools and Equipment).

Circuit/System Verification

Note: DTC P3401, P3425, P3441, and P3449 sets with an open ignition circuit fuse.

1. Ignition ON, command the appropriate cylinder deactivation solenoid ON and OFF while observing the following status parameters with a

scan tool:

* Cyl. 1, 4, 6, or 7 Deact. Sol. Ckt Open Test Status

* Cyl. 1, 4, 6, or 7 Deact. Sol. Ckt Short Gnd Test Status

* Cyl. 1, 4, 6, or 7 Deact. Sol. Ckt Short Volts Test Status

Each parameter should display OK or Not Run

2. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Ignition OFF, remove the intake manifold. Refer to Intake Manifold Replacement (Without AFM) (See: Engine, Cooling and

Exhaust/Engine/Intake Manifold/Service and Repair)Intake Manifold Replacement (With AFM) (See: Engine, Cooling and

Exhaust/Engine/Intake Manifold/Service and Repair).

2. Disconnect the harness connector at the valve lifter oil manifold assembly.

3. Ignition ON, verify that a test lamp illuminates between the ignition circuit terminal E and ground.

瀚慖f the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit tests normal and

the ignition circuit fuse is open, test all the components connected to the ignition circuit and replace as necessary.

4. Verify that a test lamp does not illuminate between the ignition circuit terminal E and the appropriate cylinder deactivation solenoid control

circuit terminal listed below.

* Cylinder deactivation solenoid valve 1 terminal C

* Cylinder deactivation solenoid valve 2 terminal A

* Cylinder deactivation solenoid valve 3 terminal B

* Cylinder deactivation solenoid valve 4 terminal D

瀚慖f the test lamp illuminates, test the control circuit for a short to ground. If the circuit tests normal, replace the ECM.

5. Remove the test lamp.

6. Command the appropriate cylinder deactivation solenoid ON with a scan tool. Verify the scan tool Cylinder Deactivation Solenoid Valve

Control Circuit High Voltage Test Status parameter displays OK.

瀚慖f not the specified value, test the appropriate control circuit listed below for a short to voltage. If the circuit tests normal, replace the

ECM.

* Cylinder deactivation solenoid valve 1 terminal C

* Cylinder deactivation solenoid valve 2 terminal A

* Cylinder deactivation solenoid valve 3 terminal B

* Cylinder deactivation solenoid valve 4 terminal D

7. Install a 3 A fused jumper wire between the appropriate control circuit terminal listed below and the ignition circuit terminal E. Command the

appropriate cylinder deactivation solenoid ON with a scan tool. Verify the scan tool Cylinder Deactivation Solenoid Valve Control Circuit

High Voltage Test Status parameter displays Malfunction.

* Cylinder deactivation solenoid valve 1 terminal C

* Cylinder deactivation solenoid valve 2 terminal A

2010 Cadillac Truck Escalade RWD V8-6.2L Page 2175

2010 Cadillac Truck Escalade RWD V8-6.2L Page 2175

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Circuit/System Verification

Note: This DTC may be stored as a history DTC without affecting the operation of the module. If stored only as a history DTC and not retrieved as

a current DTC, do not replace the module.

1. Verify that DTC P0602 is not set.

瀚慖f the DTC is set, program the K27 fuel pump control module.

2. Verify that DTCs P0601, P0603, P0604, P0606, and P062F are not set.

瀚慖f the DTCs are set, program the K27 fuel pump control module. If the DTCs reset, replace the K27 fuel pump control module.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

Control Module References (See: Testing and Inspection/Programming and Relearning)for fuel pump control module replacement, setup, and

programming

2ML70 - Automatic Transmission

DTC P0601-P0606, P060B, or P062F

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptor

DTC P0601

- Transmission Control Module (TCM) Read Only Memory (ROM)

DTC P0602

- Transmission Control Module (TCM) Not Programmed

DTC P0603

- Transmission Control Module (TCM) Long Term Memory Reset

DTC P0604

- Transmission Control Module (TCM) Random Access Memory (RAM)

DTC P0606

- Transmission Control Module (TCM) Internal Performance

DTC P060B

- Control Module Analog to Digital Performance

DTC P062F

- Transmission Control Module (TCM) Long Term Memory Performance

Circuit/System Description

This is an internal fault detection of the transmission control module. This fault is handled inside the transmission control module and no external

circuits are involved. The transmission control module is part of the control solenoid valve assembly, and is not serviced separately.

2010 Cadillac Truck Escalade RWD V8-6.2L Page 2126

2010 Cadillac Truck Escalade RWD V8-6.2L Page 2126

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning)for scan tool information

Circuit/System Testing

1. Engine running, accessories OFF, measure and record the battery voltage at the battery terminals. The voltage should be between 12.6 and

15.0 volts.

瀚慖f not within the specified range, refer to Charging System Test (See: Starting and Charging/Testing and Inspection/Component Tests

and General Diagnostics/Charging System Test).

2. Ignition OFF, disconnect the harness connectors at the ECM.

3. Ignition OFF and scan tool disconnected, open and close the driver door, and wait 1 minute. Test for less than 5 ohms of resistance between

the ground circuit terminal 73 X1 and ground.

瀚慖f greater than the specified range, test the ground circuit for an open/high resistance.

4. Verify that a test lamp illuminates between the B+ circuit terminal 20 X1 and ground.

瀚慖f the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance.

5. Install a 3A jumper wire between the PWR/TRN relay control circuit terminal 59 X1 and ground.

6. Ignition ON, verify that a test lamp illuminates between the ignition circuit terminals listed below and ground.

* Terminal 19 X1

* Terminal 47 X1

瀚慖f the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance.

7. If all circuits test normal, replace the ECM.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

Control Module References (See: Testing and Inspection/Programming and Relearning)for ECM replacement, setup, and programming.

FPCM

DTC P0562 (FPCM)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptor

DTC P0562

- System Voltage Low - FPCM

Diagnostic Fault Information

Circuit/System Description

The fuel pump control module (FPCM) monitors the system voltage to ensure that the voltage stays within the proper range. Damage to