2010 Cadillac Truck SRX AWD V6-3.0L Page 977
* Heated Oxygen Sensor Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical
Diagnostic Procedures/Wiring Repairs/Heated Oxygen Sensor Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Verification
1. Ignition ON, observe the DTC information with a scan tool. Verify no B52 HO2S heater DTCs are set.
瀚慖f a B52 HO2S heater DTC is set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code
Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle).
2. Engine running, observe the appropriate scan tool B52 HO2S voltage parameter. The reading should be within the range of 50-1,050 mV.
3. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the
conditions that you observed from the Freeze Frame/Failure Records data.
Circuit/System Testing
1. Verify none of the following conditions exist:
* Lean or rich fuel injectors-Refer to Fuel Injector Solenoid Coil Test (LAU) (See: Powertrain Management/Fuel Delivery and Air
Induction/Fuel Injector/Testing and Inspection)Fuel Injector Solenoid Coil Test (LF1, LFW) (See: Powertrain Management/Fuel
Delivery and Air Induction/Fuel Injector/Testing and Inspection).
* Water intrusion in the B52 HO2S harness connector
* Low or high fuel system pressure-Refer to Fuel System Diagnosis (LF1 China) (See: Powertrain Management/Fuel Delivery and Air
Induction/Fuel Pump/Testing and Inspection/Fuel System Diagnosis (China))Fuel System Diagnosis (LF1 Except China) (See:
Powertrain Management/Fuel Delivery and Air Induction/Fuel Pump/Testing and Inspection/Fuel System Diagnosis (Except China))Fuel
System Diagnosis (LAU China) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Pump/Testing and Inspection/Fuel
System Diagnosis (China))Fuel System Diagnosis (LAU Except China) (See: Powertrain Management/Fuel Delivery and Air
Induction/Fuel Pump/Testing and Inspection/Fuel System Diagnosis (Except China)).
* Fuel that is contaminated-Refer to Alcohol/Contaminants-in-Fuel Diagnosis (Special Tool) (See: Powertrain Management/Fuel Delivery
and Air Induction/Fuel/Testing and Inspection/Alcohol/Contaminants-in-Fuel Diagnosis (Special Tool))Alcohol/Contaminants-in-Fuel
Diagnosis (Without Special Tool) (See: Powertrain Management/Computers and Control Systems/Testing and Inspection/Component
Tests and General Diagnostics/Alcohol/Contaminants-in-Fuel Diagnosis (Without Special Tool)).
* Fuel saturation of the evaporative emission (EVAP) canister
* Exhaust leaks near the B52 HO2S
* Engine vacuum leaks
* Engine oil consumption-Refer to Oil Consumption Diagnosis (See: Engine, Cooling and Exhaust/Engine/Testing and
Inspection/Component Tests and General Diagnostics/Oil Consumption Diagnosis).
* Engine coolant consumption-Refer to Loss of Coolant (See: Engine, Cooling and Exhaust/Cooling System/Testing and
Inspection/Symptom Related Diagnostic Procedures/Loss of Coolant).
瀚慖f you find any of the above conditions, repair as necessary.
2. If all conditions test normal, test or replace the appropriate B52 HO2S.
Repair Instructions
Caution: Refer to Heated Oxygen Sensor Resistance Learn Reset Caution (See: Powertrain Management/Computers and Control
Systems/Oxygen Sensor/Service Precautions/Heated Oxygen Sensor Resistance Learn Reset Caution).
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 (LF1) (See: Powertrain Management/Computers and Control Systems/Oxygen
Sensor/Service and Repair/Heated Oxygen Sensor Replacement - Bank 1 Sensor 1)
* Heated Oxygen Sensor Replacement - Bank 1 Sensor 2 (LF1) (See: Powertrain Management/Computers and Control Systems/Oxygen
Sensor/Service and Repair/Heated Oxygen Sensor Replacement - Bank 1 Sensor 2)
* Heated Oxygen Sensor Replacement - Bank 2 Sensor 1 (LF1) (See: Powertrain Management/Computers and Control Systems/Oxygen
Sensor/Service and Repair/Heated Oxygen Sensor Replacement - Bank 2 Sensor 1)
* Heated Oxygen Sensor Replacement - Bank 2 Sensor 2 (LF1) (See: Powertrain Management/Computers and Control Systems/Oxygen
Sensor/Service and Repair/Heated Oxygen Sensor Replacement - Bank 2 Sensor 2)
* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming
