2010 Cadillac Truck Escalade RWD V8-6.2L Page 1484
Component Connector End Views (See: Diagrams/Connector Views)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Verification
Important: The HPCM must command the high voltage contactor relays closed in order for HVIC to be enabled. Fail will be
displayed if any DTCs present at ignition ON prevent the HPCM from closing the high voltage contactor relays.
1. Capture and then clear the DTC information.
2. Ignition OFF, wait 2 minutes.
3. Ignition ON, observe the HPCMs BECM HVIC Status and HPCM HVIC Status parameters.
瀚慣he parameters should both indicate a PASS condition.
Circuit/System Testing
P1B05 and P1B06 without P1AE2, P1AE3 or P1AE4
Important: DTC P1B05 and P1B06 should always pass and fail together. If one DTC has passed while one has failed, replace the
drive motor generator power inverter control module (PIM).
1. Ignition OFF, wait 2 minutes.
Important: The drive motor generator control module sight shield must be installed during all testing in order to complete the HVIC
current loop.
2. Disconnect PIM connector X1.
3. Ignition ON, observe the BECM HVIC Current Source parameter.
瀚慖f the HVIC Current Source parameter indicates current less than 5 mA, replace the PIM.
瀚慖f the HVIC Current Source parameter indicates current between 5-18 mA test for the HVIC Source and HVIC Return circuits shorted
together between PIM connector X1 and X350.
Danger: Always perform the High Voltage Disabling procedure prior to servicing any High Voltage component or connection. Personal
Protection Equipment (PPE) and proper procedures must be followed.
The High Voltage Disabling procedure will perform the following tasks:
* Identify how to disable high voltage.
* Identify how to test for the presence of high voltage.
* Identify condition under which high voltage is always present and personal protection equipment (PPE) and proper procedures
must be followed.
Failure to follow the procedures exactly as written may result in serious injury or death.
Important: Removal of the HV manual disconnect lever also opens the HVIC source circuit between X350 and BECM connector X1.
瀚慖f the circuit tests normal, perform the High Voltage Disabling () procedure and test for the HVIC Source and HVIC Return circuits
shorted together between X350 and BECM connector X1. If the circuit tests normal, replace the BECM.
P1B05 and P1B06 with P1AE2
CADILLAC Diagnostic and Repair Information ,Wiring Diagrams. DTC. TSB. Types: TSB, DTC, Wiring Diagrams, OEM Procedures. Trusted by more than 400,000 technicians. OEM accurate fix for faster repairs. Repair Procedures and Labor Times. Factory Auto Repair info. Request A Demo Today. Factory-Correct Diagrams. Factory Part Numbers. Maintenance Schedules. Repair Procedures. Labor Times. Types: TSB, DTC.