2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 2652
Conditions for Setting the DTC
The transmission control module detects shift solenoid valve 1 is ON when commanded OFF.
Action Taken When the DTC Sets
P0752 is a Type B DTC.
Conditions for Clearing the DIC/DTC
P0752 is a Type B DTC.
Reference Information
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Circuit/System Verification
1. Verify that P0721, P0722, P0723, P0966, P0967, P0969, P0970, P0971, P0973, P0974, P0976, P0977, P2720, P2721, P2728, P2729, or
P2730 is not set.
瀚慖f any of the DTCs are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code
Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle).
2. Perform the Transmission Fluid Level and Condition Check (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing
and Inspection/Symptom Related Diagnostic Procedures/2ML70 - Automatic Transmission/Transmission Fluid Level and Condition Check).
3. Perform the Line Pressure Check (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing and Inspection/Component
Tests and General Diagnostics/2ML70 - Automatic Transmission/Line Pressure Check).
4. Perform the Control Solenoid Valve and Transmission Control Module Assembly Inspection (See: Transmission and Drivetrain/Automatic
Transmission/Transaxle/Testing and Inspection/Component Tests and General Diagnostics/2ML70 - Automatic Transmission/Control
Solenoid Valve and Transmission Control Module Assembly Inspection).
5. Perform the Control Solenoid Valve and Transmission Control Module Assembly Solenoid Performance Test (See: Transmission and
Drivetrain/Automatic Transmission/Transaxle/Testing and Inspection/Component Tests and General Diagnostics/2ML70 - Automatic
Transmission/Control Solenoid Valve and Transmission Control Module Assembly Solenoid Performance Test).
瀚慖f the shift solenoid 1 is found to be leaking or stuck OFF, replace the control solenoid (w/body and TCM) valve assembly.
瀚慖f the control solenoid (w/body and TCM) valve assembly tests normal, inspect the valve body and hydraulic circuits for a leak or a stuck
valve.
6. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the
conditions that you observed from the Freeze Frame/Failure Records data.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Control Module References (See: Testing and Inspection/Programming and Relearning) for control solenoid valve assembly replacement,
setup, and programming
* Control Valve Upper Body Replacement (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Valve Body/Service and
Repair/2ML70 - Automatic Transmission) for control valve body repair or replacement.
6L50/6L80/6L90 - Automatic Transmission
DTC P0756
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
