2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1336
Note: The control module or the sensor may be damaged if the circuit is shorted to B+ voltage.
3. Test for 5 ohm or less between the low reference circuit terminal 1 and ground.
瀚慖f greater than the specified range, test the low reference circuit for an open/high resistance or for a short to voltage. If the
circuit/connections test normal, replace the ECM.
4. Install the fuse that supplies B+ to terminal 56-X2 of the ECM.
5. Ignition ON, test for greater than 4.8 V between the 5-volt reference circuit terminal 3 and ground.
瀚慖f less than the specified value, test the 5-volt reference circuit for an open/high resistance. If the circuits/connections test normal, replace
the ECM.
6. Test for 4.8-5.2 V between the signal circuit terminal 2 and ground.
瀚慖f the voltage is greater than specified range, test for a short to voltage in the signal circuit. If circuit/connections test normal, replace the
ECM.
瀚慖f the voltage is less than the specified range, test for a short to ground or an open/high resistance in the signal circuit. If
circuit/connections test normal, replace the ECM.
7. If all circuits/connections test normal, replace the camshaft position sensor.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Camshaft Position Sensor Replacement - Bank 2 (Left Side) Exhaust (See: Powertrain Management/Computers and Control
Systems/Camshaft Position Sensor/Service and Repair/Camshaft Position Sensor Replacement - Bank 2 (Left Side) Exhaust)
* Camshaft Position Sensor Replacement - Bank 2 (Left Side) Intake (See: Powertrain Management/Computers and Control
Systems/Camshaft Position Sensor/Service and Repair/Camshaft Position Sensor Replacement - Bank 2 (Left Side) Intake)
* Camshaft Position Sensor Replacement - Bank 1 (Right Side) Exhaust (See: Powertrain Management/Computers and Control
Systems/Camshaft Position Sensor/Service and Repair/Camshaft Position Sensor Replacement - Bank 1 (Right Side) Exhaust)
* Camshaft Position Sensor Replacement - Bank 1 (Right Side) Intake (See: Powertrain Management/Computers and Control
Systems/Camshaft Position Sensor/Service and Repair/Camshaft Position Sensor Replacement - Bank 1 (Right Side) Intake)
* Control Module References (See: Testing and Inspection/Programming and Relearning) for engine control module replacement, setup, and
programming
P0393
DTC P0341, P0342, P0343, P0346, P0347, P0348, P0366, P0367, P0368, P0391, P0392, or P0393 (LAU)
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC P0341
- Intake Camshaft Position Sensor Performance Bank 1
DTC P0342
- Intake Camshaft Position Sensor Circuit Low Voltage Bank 1
DTC P0343
- Intake Camshaft Position Sensor Circuit High Voltage Bank 1
DTC P0346
- Intake Camshaft Position Sensor Performance Bank 2
DTC P0347
- Intake Camshaft Position Sensor Circuit Low Voltage Bank 2
DTC P0348
- Intake Camshaft Position Sensor Circuit High Voltage Bank 2
