Diagram/Instrument Cluster Schematics)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Data Link Communications Description and Operation (See: Powertrain Management/Computers and Control Systems/Information
Bus/Description and Operation)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Verification
1. Verify that DTC U1500 31 is not set,
锟斤拷If the DTC is set, replace the appropriate window motor.
2. Verify that DTC U1511 is not set in the BCM.
锟斤拷If DTC U1511 is set in the BCM, perform the Compass Malfunction Test.
3. Perform the Window Malfunction Test.
Circuit/System Testing
Compass Malfunction Test
1. Ignition OFF, disconnect the harness connector at the electronic compass module.
2. Ignition OFF, test for less than 5.0 ohm between the ground circuit terminal 2 and ground.
锟斤拷If greater than the specified range, test the ground circuit for an open/high resistance.
3. Ignition ON, verify a test lamp illuminates between the ignition circuit terminal 1 and ground.
锟斤拷If the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance.
4. Test for 6.0-7.0 V between the LIN Bus circuit terminal 3 and ground.
锟斤拷If greater than the specified range, test the LIN Bus circuit for a short to voltage. If the circuit tests normal, replace the BCM.
锟斤拷If less than the specified range, test the LIN Bus circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace
the BCM.
5. If all circuits test normal, replace the electronic compass module.
Window Malfunction Test
1. Ignition OFF, disconnect the harness connector at the appropriate window motor.
2. Ignition OFF, test for less than 2.0 ohm between the ground circuit terminal 4 and ground.
锟斤拷If greater than the specified range, test the ground circuit for an open/high resistance.
3. Ignition ON, verify a test lamp illuminates between the B+ circuit terminal 3 and ground.
锟斤拷If the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance.
4. Test for 6.0-7.0 V between the LIN circuit terminal 5 and ground.
锟斤拷If greater than the specified range, test the LIN circuit for a short to voltage. If the circuit tests normal, replace the door module.
锟斤拷If less than the specified range, test the LIN circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the
CADILLAC Diagnostic and Repair Information ,Wiring Diagrams. DTC. TSB. Types: TSB, DTC, Wiring Diagrams, OEM Procedures. Trusted by more than 400,000 technicians. OEM accurate fix for faster repairs. Repair Procedures and Labor Times. Factory Auto Repair info. Request A Demo Today. Factory-Correct Diagrams. Factory Part Numbers. Maintenance Schedules. Repair Procedures. Labor Times. Types: TSB, DTC.