2010 Cadillac CTS Sedan AWD V6-3.6L Page 1205
Engine Controls Schematics (LLT) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics
(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Throttle Actuator Control (TAC) System Description (See: Powertrain Management/Computers and Control Systems/Description and
Operation/Throttle Actuator Control (TAC) System Description)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit
Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Wiring Repairs/Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Verification
1. Ignition ON, verify that DTC P0697, P0698, or P0699 is not set.
瀚慖f a DTC is set, refer to DTC P0641-P0643, P0651-P0653, or P0697-P0699 (ECM, LLT) ( See: P Code Charts/P0641).
2. Clear the DTC Info with a scan tool.
3. Start the engine, observe the scan tool Throttle Position Sensor 1 and 2 voltage parameters. TP sensor 1 should be between 0.17-4.6 V and
TP sensor 2 should be between 0.15-4.8 V.
4. Observe the scan tool Throttle Position sensor 1 and 2 parameters while performing the tests listed below. The parameter should display
Agree.
* Rapidly depress the accelerator pedal from the rest position to the wide open throttle position (WOT) and release pedal. Repeat the
procedure several times.
* Slowly depress the accelerator pedal to WOT and then slowly return the pedal to closed throttle. Repeat the procedure several times.
5. Observe the DTC Information with a scan tool. DTCs P0121, P0122, P0123, P0221, P0222, and P0223 should not set.
6. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the
conditions that you observed from the Freeze Frame/Failure Records data.
Circuit/System Testing
1. Ignition OFF, disconnect the harness connector at throttle body.
2. Ignition OFF, remove the fuse that supplies B+ to terminal 56 X2 of the ECM.
Note: The control module or the sensor may be damaged if the circuit is shorted to battery positive voltage.
3. Test for less than 5 ohm between the low reference circuit terminal C and ground.
瀚慖f greater than the specified range, test the low reference circuit for a short to voltage or an open/high resistance. If the circuit tests
normal, replace the Engine Control Module.
4. Install fuse that supplies B+ to terminal 56 X2 of the ECM.
5. Ignition ON, test for 4.8-5.2 V between the 5 V reference circuit terminal E and ground.
瀚慖f less than the specified range, test the circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the
Engine Control Module.
瀚慖f greater than the specified range, test the circuit for a short to voltage. If the circuit tests normal, replace the Engine Control Module.
6. Ignition ON, verify that the scan tool Throttle Position Sensor 1 voltage parameter is less than 0.3 V.
瀚慖f greater than the specified value, test the signal circuit terminal D for a short to voltage. If the circuit tests normal, replace the Engine
