锟斤拷If less than the specified range, test the signal circuit for short to ground or an open/high resistance. If the circuit tests normal, replace the
ECM.
6. If all circuits test normal, test or replace the FTP sensor.
Repair Instructions
* For DTC P0452 or P0453, always perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic
procedure
* For DTC P0451 or P0454, clear DTCs with a scan tool
* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup and programming
P0455
DTC P0455
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions)provides an overview of each diagnostic category.
DTC Descriptor
DTC P0455
- Evaporative Emission (EVAP) System Large Leak Detected
Circuit/System Description
The ECM tests the Evaporative Emission (EVAP) System for a large leak or restrictions to the purge path in the EVAP system. When the enabling
criteria has been met the ECM commands the EVAP canister vent solenoid valve ON and the EVAP canister purge solenoid valve ON, allowing
vacuum into the EVAP system. The ECM monitors the fuel tank pressure (FTP) sensor voltage to verify that the system is able to reach a
predetermined level of vacuum within a set amount of time.
Conditions for Running the DTC
* Before the ECM can report DTC P0455 failed, DTC P0496 must run and pass.
* DTCs P0106, P0107, P0108, P0116, P0117, P0118, P0120, P0121, P0122, P0123, P0220, P0222, P0223, P0442, P0443, P0449, P0451,
P0452, P0453, P0454, P0464, P0496, P0608, P0609, P0641, P0651, P1516, P2101, P2119, P2120, P2122, P2123, P2125, P2127, P2128,
P2135, P2138 are not set.
* The ignition voltage is between 11-18 volts.
* The barometric pressure (BARO) is more than 74 kPa.
* The fuel level is between 15-85 percent.
* The engine coolant temperature (ECT) is less than 35锟斤拷C (95锟斤拷F).
* The intake air temperature (IAT) is between 4-30锟斤拷C (39-86锟斤拷F).
* DTC P0455 runs once per cold start when the above conditions are met.
Conditions for Setting the DTC
The EVAP system is not able to achieve or maintain a calibrated level of vacuum within a set amount of time.
Action Taken When the DTC Sets
DTC P0455 is a Type B DTC.
Conditions for Clearing the MIL/DTC
DTC P0455 is a Type B DTC.
Diagnostic Aids
* Inspect for a loose, missing, damaged, or incorrect fuel fill cap.
* Inspect for a damaged fuel filler neck seal surface.
* A blockage or restriction in the EVAP purge solenoid valve, purge pipe, EVAP canister, or vapor pipe, can cause this DTC to set.
* The EVAP system can be filled with smoke more quickly and completely by opening the system opposite the end where the smoke is
Showing posts with label test the signal circuit for short to ground or an open/high resistance. If the circuit tests normal. Show all posts
Showing posts with label test the signal circuit for short to ground or an open/high resistance. If the circuit tests normal. Show all posts
Thursday, December 19, 2019
Wednesday, November 27, 2019
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 516
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 516
瀚慖f less than the specified range, test the signal circuit for short to ground or an open/high resistance. If the circuit tests normal, replace the
MSM.
6. If all circuits test normal, test or replace the lumbar position sensor.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Front Seat Adjuster Replacement (with HP2) ()Front Seat Adjuster Replacement (without HP2) ()
* Seat Lumbar Sub System Replacement ()
* Front Seat Recliner Actuator Motor Replacement ()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for MSM replacement, setup, and programming
B1860
DTC B1825, B1850, B1860, B2355, B2365, or B2375
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC B1825 01
- Seat Recline Position Sensor Circuit Short to Battery
DTC B1825 06
- Seat Recline Position Sensor Circuit Short to Ground or Open
DTC B1825 5A
- Seat Recline Position Sensor Circuit Plausibility Failure
DTC B1850 01
- Left Seat Lumbar Horizontal Position Sensor Circuit Short to Battery
DTC B1850 06
- Left Seat Lumbar Horizontal Position Sensor Circuit Short to Ground or Open
DTC B1850 5A
- Left Seat Lumbar Horizontal Position Sensor Circuit Plausibility Failure
DTC B1860 01
- Left Seat Lumbar Vertical Position Sensor Circuit Short to Battery
DTC B1860 06
- Left Seat Lumbar Vertical Position Sensor Circuit Short to Ground or Open
DTC B1860 5A
- Left Seat Lumbar Vertical Position Sensor Circuit Plausibility Failure
DTC B2355 01
- Left Seat Front Vertical Position Sensor Circuit Short to Battery
DTC B2355 06
- Left Seat Front Vertical Position Sensor Circuit Short to Ground or Open
DTC B2355 5A
- Left Seat Front Vertical Position Sensor Circuit Plausibility Failure
DTC B2365 01
- Left Seat Rear Vertical Position Sensor Circuit Short to Battery
瀚慖f less than the specified range, test the signal circuit for short to ground or an open/high resistance. If the circuit tests normal, replace the
MSM.
6. If all circuits test normal, test or replace the lumbar position sensor.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Front Seat Adjuster Replacement (with HP2) ()Front Seat Adjuster Replacement (without HP2) ()
* Seat Lumbar Sub System Replacement ()
* Front Seat Recliner Actuator Motor Replacement ()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for MSM replacement, setup, and programming
B1860
DTC B1825, B1850, B1860, B2355, B2365, or B2375
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC B1825 01
- Seat Recline Position Sensor Circuit Short to Battery
DTC B1825 06
- Seat Recline Position Sensor Circuit Short to Ground or Open
DTC B1825 5A
- Seat Recline Position Sensor Circuit Plausibility Failure
DTC B1850 01
- Left Seat Lumbar Horizontal Position Sensor Circuit Short to Battery
DTC B1850 06
- Left Seat Lumbar Horizontal Position Sensor Circuit Short to Ground or Open
DTC B1850 5A
- Left Seat Lumbar Horizontal Position Sensor Circuit Plausibility Failure
DTC B1860 01
- Left Seat Lumbar Vertical Position Sensor Circuit Short to Battery
DTC B1860 06
- Left Seat Lumbar Vertical Position Sensor Circuit Short to Ground or Open
DTC B1860 5A
- Left Seat Lumbar Vertical Position Sensor Circuit Plausibility Failure
DTC B2355 01
- Left Seat Front Vertical Position Sensor Circuit Short to Battery
DTC B2355 06
- Left Seat Front Vertical Position Sensor Circuit Short to Ground or Open
DTC B2355 5A
- Left Seat Front Vertical Position Sensor Circuit Plausibility Failure
DTC B2365 01
- Left Seat Rear Vertical Position Sensor Circuit Short to Battery
Thursday, November 14, 2019
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 579
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 579
瀚慖f less than the specified range, test the signal circuit for short to ground or an open/high resistance. If the circuit tests normal, replace the
MSM.
6. If all circuits test normal, test or replace the lumbar position sensor.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Front Seat Adjuster Replacement (with HP2) ()Front Seat Adjuster Replacement (without HP2) ()
* Seat Lumbar Sub System Replacement ()
* Front Seat Recliner Actuator Motor Replacement ()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for MSM replacement, setup, and programming
B2365
DTC B1825, B1850, B1860, B2355, B2365, or B2375
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC B1825 01
- Seat Recline Position Sensor Circuit Short to Battery
DTC B1825 06
- Seat Recline Position Sensor Circuit Short to Ground or Open
DTC B1825 5A
- Seat Recline Position Sensor Circuit Plausibility Failure
DTC B1850 01
- Left Seat Lumbar Horizontal Position Sensor Circuit Short to Battery
DTC B1850 06
- Left Seat Lumbar Horizontal Position Sensor Circuit Short to Ground or Open
DTC B1850 5A
- Left Seat Lumbar Horizontal Position Sensor Circuit Plausibility Failure
DTC B1860 01
- Left Seat Lumbar Vertical Position Sensor Circuit Short to Battery
DTC B1860 06
- Left Seat Lumbar Vertical Position Sensor Circuit Short to Ground or Open
DTC B1860 5A
- Left Seat Lumbar Vertical Position Sensor Circuit Plausibility Failure
DTC B2355 01
- Left Seat Front Vertical Position Sensor Circuit Short to Battery
DTC B2355 06
- Left Seat Front Vertical Position Sensor Circuit Short to Ground or Open
DTC B2355 5A
- Left Seat Front Vertical Position Sensor Circuit Plausibility Failure
DTC B2365 01
- Left Seat Rear Vertical Position Sensor Circuit Short to Battery
瀚慖f less than the specified range, test the signal circuit for short to ground or an open/high resistance. If the circuit tests normal, replace the
MSM.
6. If all circuits test normal, test or replace the lumbar position sensor.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Front Seat Adjuster Replacement (with HP2) ()Front Seat Adjuster Replacement (without HP2) ()
* Seat Lumbar Sub System Replacement ()
* Front Seat Recliner Actuator Motor Replacement ()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for MSM replacement, setup, and programming
B2365
DTC B1825, B1850, B1860, B2355, B2365, or B2375
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC B1825 01
- Seat Recline Position Sensor Circuit Short to Battery
DTC B1825 06
- Seat Recline Position Sensor Circuit Short to Ground or Open
DTC B1825 5A
- Seat Recline Position Sensor Circuit Plausibility Failure
DTC B1850 01
- Left Seat Lumbar Horizontal Position Sensor Circuit Short to Battery
DTC B1850 06
- Left Seat Lumbar Horizontal Position Sensor Circuit Short to Ground or Open
DTC B1850 5A
- Left Seat Lumbar Horizontal Position Sensor Circuit Plausibility Failure
DTC B1860 01
- Left Seat Lumbar Vertical Position Sensor Circuit Short to Battery
DTC B1860 06
- Left Seat Lumbar Vertical Position Sensor Circuit Short to Ground or Open
DTC B1860 5A
- Left Seat Lumbar Vertical Position Sensor Circuit Plausibility Failure
DTC B2355 01
- Left Seat Front Vertical Position Sensor Circuit Short to Battery
DTC B2355 06
- Left Seat Front Vertical Position Sensor Circuit Short to Ground or Open
DTC B2355 5A
- Left Seat Front Vertical Position Sensor Circuit Plausibility Failure
DTC B2365 01
- Left Seat Rear Vertical Position Sensor Circuit Short to Battery
Subscribe to:
Posts (Atom)