Showing posts with label test the circuit for a short to ground or an open/high resistance. If the circuit/connection tests normal. Show all posts
Showing posts with label test the circuit for a short to ground or an open/high resistance. If the circuit/connection tests normal. Show all posts

Saturday, October 31, 2020

2010 Cadillac CTS Sedan AWD V6-3.0L Page 1953

2010 Cadillac CTS Sedan AWD V6-3.0L Page 1953



瀚慖f less than the specified range, test the circuit for a short to ground or an open/high resistance. If the circuit/connection tests normal,



replace the K20 ECM.



瀚慖f greater than the specified range, test the circuit for a short to voltage. If the circuit/connection tests normal, replace the K20 ECM.



4. Connect a test lamp between the each of the ground circuits terminal A, and terminal B, and B+. The test lamp should illuminate on each



circuit.



瀚慖f the test lamp does not illuminate, test the suspected circuit for an open/high resistance.



5. If all circuits/connections test normal, replace the T8 ignition coil.



Repair Instructions



Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.



* Ignition Coil Replacement - Bank 1 (See: Powertrain Management/Ignition System/Ignition Coil/Service and Repair/Ignition Coil



Replacement - Bank 1)



* Ignition Coil Replacement - Bank 2 (See: Powertrain Management/Ignition System/Ignition Coil/Service and Repair/Ignition Coil



Replacement - Bank 2)



* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming



P2306



DTC P0351-P0356, P2300, P2301, P2303, P2304, P2306, P2307, P2309, P2310, P2312, P2313, P2315, or P2316 (w/LLT)



Diagnostic Instructions



* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System



Check - Vehicle) prior to using this diagnostic procedure.



* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an



overview of the diagnostic approach.



* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure



Instructions) provides an overview of each diagnostic category.



DTC Descriptors



DTC P0351



- Ignition Coil 1 Control Circuit



DTC P0352



- Ignition Coil 2 Control Circuit



DTC P0353



- Ignition Coil 3 Control Circuit



DTC P0354



- Ignition Coil 4 Control Circuit



DTC P0355



- Ignition Coil 5 Control Circuit



DTC P0356



- Ignition Coil 6 Control Circuit



DTC P2300



- Ignition Coil 1 Control Circuit Low Voltage



DTC P2301



- Ignition Coil 1 Control Circuit High Voltage



DTC P2303



- Ignition Coil 2 Control Circuit Low Voltage



DTC P2304



- Ignition Coil 2 Control Circuit High Voltage



DTC P2306



- Ignition Coil 3 Control Circuit Low Voltage

Wednesday, October 21, 2020

2010 Cadillac CTS Sedan AWD V6-3.0L Page 1962

2010 Cadillac CTS Sedan AWD V6-3.0L Page 1962



瀚慖f less than the specified range, test the circuit for a short to ground or an open/high resistance. If the circuit/connection tests normal,



replace the K20 ECM.



瀚慖f greater than the specified range, test the circuit for a short to voltage. If the circuit/connection tests normal, replace the K20 ECM.



4. Connect a test lamp between the each of the ground circuits terminal A, and terminal B, and B+. The test lamp should illuminate on each



circuit.



瀚慖f the test lamp does not illuminate, test the suspected circuit for an open/high resistance.



5. If all circuits/connections test normal, replace the T8 ignition coil.



Repair Instructions



Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.



* Ignition Coil Replacement - Bank 1 (See: Powertrain Management/Ignition System/Ignition Coil/Service and Repair/Ignition Coil



Replacement - Bank 1)



* Ignition Coil Replacement - Bank 2 (See: Powertrain Management/Ignition System/Ignition Coil/Service and Repair/Ignition Coil



Replacement - Bank 2)



* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming



P2310



DTC P0351-P0356, P2300, P2301, P2303, P2304, P2306, P2307, P2309, P2310, P2312, P2313, P2315, or P2316 (w/LLT)



Diagnostic Instructions



* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System



Check - Vehicle) prior to using this diagnostic procedure.



* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an



overview of the diagnostic approach.



* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure



Instructions) provides an overview of each diagnostic category.



DTC Descriptors



DTC P0351



- Ignition Coil 1 Control Circuit



DTC P0352



- Ignition Coil 2 Control Circuit



DTC P0353



- Ignition Coil 3 Control Circuit



DTC P0354



- Ignition Coil 4 Control Circuit



DTC P0355



- Ignition Coil 5 Control Circuit



DTC P0356



- Ignition Coil 6 Control Circuit



DTC P2300



- Ignition Coil 1 Control Circuit Low Voltage



DTC P2301



- Ignition Coil 1 Control Circuit High Voltage



DTC P2303



- Ignition Coil 2 Control Circuit Low Voltage



DTC P2304



- Ignition Coil 2 Control Circuit High Voltage



DTC P2306



- Ignition Coil 3 Control Circuit Low Voltage

Thursday, October 15, 2020

2010 Cadillac CTS Sedan AWD V6-3.0L Page 1944

2010 Cadillac CTS Sedan AWD V6-3.0L Page 1944



瀚慖f less than the specified range, test the circuit for a short to ground or an open/high resistance. If the circuit/connection tests normal,



replace the K20 ECM.



瀚慖f greater than the specified range, test the circuit for a short to voltage. If the circuit/connection tests normal, replace the K20 ECM.



4. Connect a test lamp between the each of the ground circuits terminal A, and terminal B, and B+. The test lamp should illuminate on each



circuit.



瀚慖f the test lamp does not illuminate, test the suspected circuit for an open/high resistance.



5. If all circuits/connections test normal, replace the T8 ignition coil.



Repair Instructions



Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.



* Ignition Coil Replacement - Bank 1 (See: Powertrain Management/Ignition System/Ignition Coil/Service and Repair/Ignition Coil



Replacement - Bank 1)



* Ignition Coil Replacement - Bank 2 (See: Powertrain Management/Ignition System/Ignition Coil/Service and Repair/Ignition Coil



Replacement - Bank 2)



* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming



P2301



DTC P0351-P0356, P2300, P2301, P2303, P2304, P2306, P2307, P2309, P2310, P2312, P2313, P2315, or P2316 (w/LLT)



Diagnostic Instructions



* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System



Check - Vehicle) prior to using this diagnostic procedure.



* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an



overview of the diagnostic approach.



* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure



Instructions) provides an overview of each diagnostic category.



DTC Descriptors



DTC P0351



- Ignition Coil 1 Control Circuit



DTC P0352



- Ignition Coil 2 Control Circuit



DTC P0353



- Ignition Coil 3 Control Circuit



DTC P0354



- Ignition Coil 4 Control Circuit



DTC P0355



- Ignition Coil 5 Control Circuit



DTC P0356



- Ignition Coil 6 Control Circuit



DTC P2300



- Ignition Coil 1 Control Circuit Low Voltage



DTC P2301



- Ignition Coil 1 Control Circuit High Voltage



DTC P2303



- Ignition Coil 2 Control Circuit Low Voltage



DTC P2304



- Ignition Coil 2 Control Circuit High Voltage



DTC P2306



- Ignition Coil 3 Control Circuit Low Voltage

Thursday, October 8, 2020

2010 Cadillac CTS Sedan AWD V6-3.0L Page 1965

2010 Cadillac CTS Sedan AWD V6-3.0L Page 1965



瀚慖f less than the specified range, test the circuit for a short to ground or an open/high resistance. If the circuit/connection tests normal,



replace the K20 ECM.



瀚慖f greater than the specified range, test the circuit for a short to voltage. If the circuit/connection tests normal, replace the K20 ECM.



4. Connect a test lamp between the each of the ground circuits terminal A, and terminal B, and B+. The test lamp should illuminate on each



circuit.



瀚慖f the test lamp does not illuminate, test the suspected circuit for an open/high resistance.



5. If all circuits/connections test normal, replace the T8 ignition coil.



Repair Instructions



Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.



* Ignition Coil Replacement - Bank 1 (See: Powertrain Management/Ignition System/Ignition Coil/Service and Repair/Ignition Coil



Replacement - Bank 1)



* Ignition Coil Replacement - Bank 2 (See: Powertrain Management/Ignition System/Ignition Coil/Service and Repair/Ignition Coil



Replacement - Bank 2)



* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming



P2312



DTC P0351-P0356, P2300, P2301, P2303, P2304, P2306, P2307, P2309, P2310, P2312, P2313, P2315, or P2316 (w/LLT)



Diagnostic Instructions



* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System



Check - Vehicle) prior to using this diagnostic procedure.



* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an



overview of the diagnostic approach.



* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure



Instructions) provides an overview of each diagnostic category.



DTC Descriptors



DTC P0351



- Ignition Coil 1 Control Circuit



DTC P0352



- Ignition Coil 2 Control Circuit



DTC P0353



- Ignition Coil 3 Control Circuit



DTC P0354



- Ignition Coil 4 Control Circuit



DTC P0355



- Ignition Coil 5 Control Circuit



DTC P0356



- Ignition Coil 6 Control Circuit



DTC P2300



- Ignition Coil 1 Control Circuit Low Voltage



DTC P2301



- Ignition Coil 1 Control Circuit High Voltage



DTC P2303



- Ignition Coil 2 Control Circuit Low Voltage



DTC P2304



- Ignition Coil 2 Control Circuit High Voltage



DTC P2306



- Ignition Coil 3 Control Circuit Low Voltage

Monday, October 5, 2020

2010 Cadillac CTS Sedan AWD V6-3.0L Page 1968

2010 Cadillac CTS Sedan AWD V6-3.0L Page 1968



瀚慖f less than the specified range, test the circuit for a short to ground or an open/high resistance. If the circuit/connection tests normal,



replace the K20 ECM.



瀚慖f greater than the specified range, test the circuit for a short to voltage. If the circuit/connection tests normal, replace the K20 ECM.



4. Connect a test lamp between the each of the ground circuits terminal A, and terminal B, and B+. The test lamp should illuminate on each



circuit.



瀚慖f the test lamp does not illuminate, test the suspected circuit for an open/high resistance.



5. If all circuits/connections test normal, replace the T8 ignition coil.



Repair Instructions



Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.



* Ignition Coil Replacement - Bank 1 (See: Powertrain Management/Ignition System/Ignition Coil/Service and Repair/Ignition Coil



Replacement - Bank 1)



* Ignition Coil Replacement - Bank 2 (See: Powertrain Management/Ignition System/Ignition Coil/Service and Repair/Ignition Coil



Replacement - Bank 2)



* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming



P2313



DTC P0351-P0356, P2300, P2301, P2303, P2304, P2306, P2307, P2309, P2310, P2312, P2313, P2315, or P2316 (w/LLT)



Diagnostic Instructions



* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System



Check - Vehicle) prior to using this diagnostic procedure.



* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an



overview of the diagnostic approach.



* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure



Instructions) provides an overview of each diagnostic category.



DTC Descriptors



DTC P0351



- Ignition Coil 1 Control Circuit



DTC P0352



- Ignition Coil 2 Control Circuit



DTC P0353



- Ignition Coil 3 Control Circuit



DTC P0354



- Ignition Coil 4 Control Circuit



DTC P0355



- Ignition Coil 5 Control Circuit



DTC P0356



- Ignition Coil 6 Control Circuit



DTC P2300



- Ignition Coil 1 Control Circuit Low Voltage



DTC P2301



- Ignition Coil 1 Control Circuit High Voltage



DTC P2303



- Ignition Coil 2 Control Circuit Low Voltage



DTC P2304



- Ignition Coil 2 Control Circuit High Voltage



DTC P2306



- Ignition Coil 3 Control Circuit Low Voltage

Monday, September 28, 2020

2010 Cadillac CTS Sedan AWD V6-3.0L Page 1956

2010 Cadillac CTS Sedan AWD V6-3.0L Page 1956



瀚慖f less than the specified range, test the circuit for a short to ground or an open/high resistance. If the circuit/connection tests normal,



replace the K20 ECM.



瀚慖f greater than the specified range, test the circuit for a short to voltage. If the circuit/connection tests normal, replace the K20 ECM.



4. Connect a test lamp between the each of the ground circuits terminal A, and terminal B, and B+. The test lamp should illuminate on each



circuit.



瀚慖f the test lamp does not illuminate, test the suspected circuit for an open/high resistance.



5. If all circuits/connections test normal, replace the T8 ignition coil.



Repair Instructions



Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.



* Ignition Coil Replacement - Bank 1 (See: Powertrain Management/Ignition System/Ignition Coil/Service and Repair/Ignition Coil



Replacement - Bank 1)



* Ignition Coil Replacement - Bank 2 (See: Powertrain Management/Ignition System/Ignition Coil/Service and Repair/Ignition Coil



Replacement - Bank 2)



* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming



P2307



DTC P0351-P0356, P2300, P2301, P2303, P2304, P2306, P2307, P2309, P2310, P2312, P2313, P2315, or P2316 (w/LLT)



Diagnostic Instructions



* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System



Check - Vehicle) prior to using this diagnostic procedure.



* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an



overview of the diagnostic approach.



* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure



Instructions) provides an overview of each diagnostic category.



DTC Descriptors



DTC P0351



- Ignition Coil 1 Control Circuit



DTC P0352



- Ignition Coil 2 Control Circuit



DTC P0353



- Ignition Coil 3 Control Circuit



DTC P0354



- Ignition Coil 4 Control Circuit



DTC P0355



- Ignition Coil 5 Control Circuit



DTC P0356



- Ignition Coil 6 Control Circuit



DTC P2300



- Ignition Coil 1 Control Circuit Low Voltage



DTC P2301



- Ignition Coil 1 Control Circuit High Voltage



DTC P2303



- Ignition Coil 2 Control Circuit Low Voltage



DTC P2304



- Ignition Coil 2 Control Circuit High Voltage



DTC P2306



- Ignition Coil 3 Control Circuit Low Voltage

Sunday, September 20, 2020

2010 Cadillac CTS Sedan AWD V6-3.0L Page 1971

2010 Cadillac CTS Sedan AWD V6-3.0L Page 1971



瀚慖f less than the specified range, test the circuit for a short to ground or an open/high resistance. If the circuit/connection tests normal,



replace the K20 ECM.



瀚慖f greater than the specified range, test the circuit for a short to voltage. If the circuit/connection tests normal, replace the K20 ECM.



4. Connect a test lamp between the each of the ground circuits terminal A, and terminal B, and B+. The test lamp should illuminate on each



circuit.



瀚慖f the test lamp does not illuminate, test the suspected circuit for an open/high resistance.



5. If all circuits/connections test normal, replace the T8 ignition coil.



Repair Instructions



Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.



* Ignition Coil Replacement - Bank 1 (See: Powertrain Management/Ignition System/Ignition Coil/Service and Repair/Ignition Coil



Replacement - Bank 1)



* Ignition Coil Replacement - Bank 2 (See: Powertrain Management/Ignition System/Ignition Coil/Service and Repair/Ignition Coil



Replacement - Bank 2)



* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming



P2315



DTC P0351-P0356, P2300, P2301, P2303, P2304, P2306, P2307, P2309, P2310, P2312, P2313, P2315, or P2316 (w/LLT)



Diagnostic Instructions



* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System



Check - Vehicle) prior to using this diagnostic procedure.



* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an



overview of the diagnostic approach.



* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure



Instructions) provides an overview of each diagnostic category.



DTC Descriptors



DTC P0351



- Ignition Coil 1 Control Circuit



DTC P0352



- Ignition Coil 2 Control Circuit



DTC P0353



- Ignition Coil 3 Control Circuit



DTC P0354



- Ignition Coil 4 Control Circuit



DTC P0355



- Ignition Coil 5 Control Circuit



DTC P0356



- Ignition Coil 6 Control Circuit



DTC P2300



- Ignition Coil 1 Control Circuit Low Voltage



DTC P2301



- Ignition Coil 1 Control Circuit High Voltage



DTC P2303



- Ignition Coil 2 Control Circuit Low Voltage



DTC P2304



- Ignition Coil 2 Control Circuit High Voltage



DTC P2306



- Ignition Coil 3 Control Circuit Low Voltage

Tuesday, September 15, 2020

2010 Cadillac CTS Sedan AWD V6-3.0L Page 1974

2010 Cadillac CTS Sedan AWD V6-3.0L Page 1974



瀚慖f less than the specified range, test the circuit for a short to ground or an open/high resistance. If the circuit/connection tests normal,



replace the K20 ECM.



瀚慖f greater than the specified range, test the circuit for a short to voltage. If the circuit/connection tests normal, replace the K20 ECM.



4. Connect a test lamp between the each of the ground circuits terminal A, and terminal B, and B+. The test lamp should illuminate on each



circuit.



瀚慖f the test lamp does not illuminate, test the suspected circuit for an open/high resistance.



5. If all circuits/connections test normal, replace the T8 ignition coil.



Repair Instructions



Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.



* Ignition Coil Replacement - Bank 1 (See: Powertrain Management/Ignition System/Ignition Coil/Service and Repair/Ignition Coil



Replacement - Bank 1)



* Ignition Coil Replacement - Bank 2 (See: Powertrain Management/Ignition System/Ignition Coil/Service and Repair/Ignition Coil



Replacement - Bank 2)



* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming



P2316



DTC P0351-P0356, P2300, P2301, P2303, P2304, P2306, P2307, P2309, P2310, P2312, P2313, P2315, or P2316 (w/LLT)



Diagnostic Instructions



* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System



Check - Vehicle) prior to using this diagnostic procedure.



* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an



overview of the diagnostic approach.



* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure



Instructions) provides an overview of each diagnostic category.



DTC Descriptors



DTC P0351



- Ignition Coil 1 Control Circuit



DTC P0352



- Ignition Coil 2 Control Circuit



DTC P0353



- Ignition Coil 3 Control Circuit



DTC P0354



- Ignition Coil 4 Control Circuit



DTC P0355



- Ignition Coil 5 Control Circuit



DTC P0356



- Ignition Coil 6 Control Circuit



DTC P2300



- Ignition Coil 1 Control Circuit Low Voltage



DTC P2301



- Ignition Coil 1 Control Circuit High Voltage



DTC P2303



- Ignition Coil 2 Control Circuit Low Voltage



DTC P2304



- Ignition Coil 2 Control Circuit High Voltage



DTC P2306



- Ignition Coil 3 Control Circuit Low Voltage

Monday, August 17, 2020

2010 Cadillac CTS Sedan AWD V6-3.0L Page 1950

2010 Cadillac CTS Sedan AWD V6-3.0L Page 1950



瀚慖f less than the specified range, test the circuit for a short to ground or an open/high resistance. If the circuit/connection tests normal,



replace the K20 ECM.



瀚慖f greater than the specified range, test the circuit for a short to voltage. If the circuit/connection tests normal, replace the K20 ECM.



4. Connect a test lamp between the each of the ground circuits terminal A, and terminal B, and B+. The test lamp should illuminate on each



circuit.



瀚慖f the test lamp does not illuminate, test the suspected circuit for an open/high resistance.



5. If all circuits/connections test normal, replace the T8 ignition coil.



Repair Instructions



Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.



* Ignition Coil Replacement - Bank 1 (See: Powertrain Management/Ignition System/Ignition Coil/Service and Repair/Ignition Coil



Replacement - Bank 1)



* Ignition Coil Replacement - Bank 2 (See: Powertrain Management/Ignition System/Ignition Coil/Service and Repair/Ignition Coil



Replacement - Bank 2)



* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming



P2304



DTC P0351-P0356, P2300, P2301, P2303, P2304, P2306, P2307, P2309, P2310, P2312, P2313, P2315, or P2316 (w/LLT)



Diagnostic Instructions



* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System



Check - Vehicle) prior to using this diagnostic procedure.



* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an



overview of the diagnostic approach.



* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure



Instructions) provides an overview of each diagnostic category.



DTC Descriptors



DTC P0351



- Ignition Coil 1 Control Circuit



DTC P0352



- Ignition Coil 2 Control Circuit



DTC P0353



- Ignition Coil 3 Control Circuit



DTC P0354



- Ignition Coil 4 Control Circuit



DTC P0355



- Ignition Coil 5 Control Circuit



DTC P0356



- Ignition Coil 6 Control Circuit



DTC P2300



- Ignition Coil 1 Control Circuit Low Voltage



DTC P2301



- Ignition Coil 1 Control Circuit High Voltage



DTC P2303



- Ignition Coil 2 Control Circuit Low Voltage



DTC P2304



- Ignition Coil 2 Control Circuit High Voltage



DTC P2306



- Ignition Coil 3 Control Circuit Low Voltage

Wednesday, August 12, 2020

2010 Cadillac CTS Sedan AWD V6-3.0L Page 1959

2010 Cadillac CTS Sedan AWD V6-3.0L Page 1959



瀚慖f less than the specified range, test the circuit for a short to ground or an open/high resistance. If the circuit/connection tests normal,



replace the K20 ECM.



瀚慖f greater than the specified range, test the circuit for a short to voltage. If the circuit/connection tests normal, replace the K20 ECM.



4. Connect a test lamp between the each of the ground circuits terminal A, and terminal B, and B+. The test lamp should illuminate on each



circuit.



瀚慖f the test lamp does not illuminate, test the suspected circuit for an open/high resistance.



5. If all circuits/connections test normal, replace the T8 ignition coil.



Repair Instructions



Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.



* Ignition Coil Replacement - Bank 1 (See: Powertrain Management/Ignition System/Ignition Coil/Service and Repair/Ignition Coil



Replacement - Bank 1)



* Ignition Coil Replacement - Bank 2 (See: Powertrain Management/Ignition System/Ignition Coil/Service and Repair/Ignition Coil



Replacement - Bank 2)



* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming



P2309



DTC P0351-P0356, P2300, P2301, P2303, P2304, P2306, P2307, P2309, P2310, P2312, P2313, P2315, or P2316 (w/LLT)



Diagnostic Instructions



* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System



Check - Vehicle) prior to using this diagnostic procedure.



* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an



overview of the diagnostic approach.



* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure



Instructions) provides an overview of each diagnostic category.



DTC Descriptors



DTC P0351



- Ignition Coil 1 Control Circuit



DTC P0352



- Ignition Coil 2 Control Circuit



DTC P0353



- Ignition Coil 3 Control Circuit



DTC P0354



- Ignition Coil 4 Control Circuit



DTC P0355



- Ignition Coil 5 Control Circuit



DTC P0356



- Ignition Coil 6 Control Circuit



DTC P2300



- Ignition Coil 1 Control Circuit Low Voltage



DTC P2301



- Ignition Coil 1 Control Circuit High Voltage



DTC P2303



- Ignition Coil 2 Control Circuit Low Voltage



DTC P2304



- Ignition Coil 2 Control Circuit High Voltage



DTC P2306



- Ignition Coil 3 Control Circuit Low Voltage

Tuesday, August 4, 2020

2010 Cadillac CTS Sedan AWD V6-3.0L Page 1977

2010 Cadillac CTS Sedan AWD V6-3.0L Page 1977



瀚慖f less than the specified range, test the circuit for a short to ground or an open/high resistance. If the circuit/connection tests normal,



replace the K20 ECM.



瀚慖f greater than the specified range, test the circuit for a short to voltage. If the circuit/connection tests normal, replace the K20 ECM.



4. Connect a test lamp between the each of the ground circuits terminal A, and terminal B, and B+. The test lamp should illuminate on each



circuit.



瀚慖f the test lamp does not illuminate, test the suspected circuit for an open/high resistance.



5. If all circuits/connections test normal, replace the T8 ignition coil.



Repair Instructions



Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.



* Ignition Coil Replacement - Bank 1 (See: Powertrain Management/Ignition System/Ignition Coil/Service and Repair/Ignition Coil



Replacement - Bank 1)



* Ignition Coil Replacement - Bank 2 (See: Powertrain Management/Ignition System/Ignition Coil/Service and Repair/Ignition Coil



Replacement - Bank 2)



* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming



Engine Controls



DTC P2534



Diagnostic Instructions



* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System



Check - Vehicle) prior to using this diagnostic procedure.



* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an



overview of the diagnostic approach.



* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure



Instructions)provides an overview of each diagnostic category.



DTC Descriptor



DTC P2534



- Ignition 1 Switch Circuit Low Voltage



Diagnostic Fault Information



Circuit/System Description



The fuel pump control module monitors the ignition voltage circuit in order to determine if the voltage is within the normal operating range.



Conditions for Running the DTC



The engine is running.



Conditions for Setting the DTC



The FPCM detects that the IGN voltage is less than 6.0 V.



Action Taken When the DTC Sets



DTC P2534 is a Type A DTC.



Conditions for Clearing the DTC



DTC P2534 is a Type A DTC.



Reference Information



Schematic Reference



Engine Controls Schematics (LLT) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics

Friday, July 10, 2020

2010 Cadillac CTS Sedan AWD V6-3.0L Page 1947

2010 Cadillac CTS Sedan AWD V6-3.0L Page 1947



瀚慖f less than the specified range, test the circuit for a short to ground or an open/high resistance. If the circuit/connection tests normal,



replace the K20 ECM.



瀚慖f greater than the specified range, test the circuit for a short to voltage. If the circuit/connection tests normal, replace the K20 ECM.



4. Connect a test lamp between the each of the ground circuits terminal A, and terminal B, and B+. The test lamp should illuminate on each



circuit.



瀚慖f the test lamp does not illuminate, test the suspected circuit for an open/high resistance.



5. If all circuits/connections test normal, replace the T8 ignition coil.



Repair Instructions



Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.



* Ignition Coil Replacement - Bank 1 (See: Powertrain Management/Ignition System/Ignition Coil/Service and Repair/Ignition Coil



Replacement - Bank 1)



* Ignition Coil Replacement - Bank 2 (See: Powertrain Management/Ignition System/Ignition Coil/Service and Repair/Ignition Coil



Replacement - Bank 2)



* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming



P2303



DTC P0351-P0356, P2300, P2301, P2303, P2304, P2306, P2307, P2309, P2310, P2312, P2313, P2315, or P2316 (w/LLT)



Diagnostic Instructions



* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System



Check - Vehicle) prior to using this diagnostic procedure.



* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an



overview of the diagnostic approach.



* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure



Instructions) provides an overview of each diagnostic category.



DTC Descriptors



DTC P0351



- Ignition Coil 1 Control Circuit



DTC P0352



- Ignition Coil 2 Control Circuit



DTC P0353



- Ignition Coil 3 Control Circuit



DTC P0354



- Ignition Coil 4 Control Circuit



DTC P0355



- Ignition Coil 5 Control Circuit



DTC P0356



- Ignition Coil 6 Control Circuit



DTC P2300



- Ignition Coil 1 Control Circuit Low Voltage



DTC P2301



- Ignition Coil 1 Control Circuit High Voltage



DTC P2303



- Ignition Coil 2 Control Circuit Low Voltage



DTC P2304



- Ignition Coil 2 Control Circuit High Voltage



DTC P2306



- Ignition Coil 3 Control Circuit Low Voltage