2010 Cadillac Truck Escalade RWD V8-6.2L Page 1539
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
1. Ignition OFF, disable the high voltage at the drive motor generator battery. Refer to High Voltage Disabling ().
2. Ignition OFF, disconnect the X1 harness connectors at the drive motor generator battery control module.
3. Ignition OFF, scan tool disconnected, open and close the driver door and wait 1 minute. Test for less than 5 ohm between the ground circuit
terminal 11 and ground.
瀚慖f greater than the specified range, test the ground circuit for an open/high resistance.
4. Verify that a test lamp illuminates between the B+ circuit terminal 1 and ground.
瀚慖f the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance.
5. Ignition ON, verify that a test lamp illuminates between the ignition circuit terminal 12 and ground.
瀚慖f the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit tests normal,
replace the serial data gateway module.
6. If all circuits test normal, replace the drive motor generator battery control module.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
Control Module References (See: Testing and Inspection/Programming and Relearning) for drive motor generator battery control module or serial
data gateway module replacement, setup, and programming
P1A01
DTC P0A1F, P1A01, P1A05, or P1A06
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC P0A1F
- Battery Energy Control Module Internal Performance
DTC P1A01
- Battery Energy Control Module Long Term Memory Performance
DTC P1A05
- Battery Energy Control Module Random Access Memory (RAM)
DTC P1A06
- Battery Energy Control Module Read Only Memory (ROM)
Circuit/System Description
The drive motor generator battery control module will diagnose its own systems and determine when a fault condition is present. Diagnostics and
system status is communicated from the drive motor generator battery control module to the drive motor generator control module through serial
data. The drive motor generator control module is the host controller for diagnostic trouble code (DTC) information.
Showing posts with label either indoors or outdoors.. Show all posts
Showing posts with label either indoors or outdoors.. Show all posts
Wednesday, June 10, 2020
Thursday, June 4, 2020
2010 Cadillac Truck Escalade RWD V8-6.2L Page 1387
2010 Cadillac Truck Escalade RWD V8-6.2L Page 1387
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
1. Ignition OFF, disable the high voltage at the drive motor generator battery. Refer to High Voltage Disabling ().
2. Disconnect the X4 harness connector at the drive motor battery control module.
3. Connect to the EL-48571 high voltage battery pin out box.
4. Install the high voltage manual disconnect lever. Measure and record each of the 20 battery voltages.
5. Each battery voltage reading should be between 10-19 V.
瀚慖f not within the specified range, replace the drive motor battery assembly.
6. Each battery voltage reading should be within 1.5 V of each other.
瀚慖f not within the specified range, replace the drive motor battery assembly.
7. If all circuits test normal, replace the drive motor battery control module.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the repair.
* Drive Motor Generator Battery Replacement and Shipping Preparation ()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for drive motor generator battery control module
replacement, setup and programming
P0B97
DTC P0B3D, P0B42, P0B47, P0B4C, P0B51, P0B56, P0B5B, P0B60, P0B65, P0B6A, P0B6F, P0B74, P0B79, P0B7E, P0B83, P0B88, P0B8D,
P0B92, P0B97, or P0B9C
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC P0B3D
- Hybrid Battery 1 Circuit Low Voltage
DTC P0B42
- Hybrid Battery 2 Circuit Low Voltage
DTC P0B47
- Hybrid Battery 3 Circuit Low Voltage
DTC P0B4C
- Hybrid Battery 4 Circuit Low Voltage
DTC P0B51
- Hybrid Battery 5 Circuit Low Voltage
DTC P0B56
- Hybrid Battery 6 Circuit Low Voltage
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
1. Ignition OFF, disable the high voltage at the drive motor generator battery. Refer to High Voltage Disabling ().
2. Disconnect the X4 harness connector at the drive motor battery control module.
3. Connect to the EL-48571 high voltage battery pin out box.
4. Install the high voltage manual disconnect lever. Measure and record each of the 20 battery voltages.
5. Each battery voltage reading should be between 10-19 V.
瀚慖f not within the specified range, replace the drive motor battery assembly.
6. Each battery voltage reading should be within 1.5 V of each other.
瀚慖f not within the specified range, replace the drive motor battery assembly.
7. If all circuits test normal, replace the drive motor battery control module.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the repair.
* Drive Motor Generator Battery Replacement and Shipping Preparation ()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for drive motor generator battery control module
replacement, setup and programming
P0B97
DTC P0B3D, P0B42, P0B47, P0B4C, P0B51, P0B56, P0B5B, P0B60, P0B65, P0B6A, P0B6F, P0B74, P0B79, P0B7E, P0B83, P0B88, P0B8D,
P0B92, P0B97, or P0B9C
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC P0B3D
- Hybrid Battery 1 Circuit Low Voltage
DTC P0B42
- Hybrid Battery 2 Circuit Low Voltage
DTC P0B47
- Hybrid Battery 3 Circuit Low Voltage
DTC P0B4C
- Hybrid Battery 4 Circuit Low Voltage
DTC P0B51
- Hybrid Battery 5 Circuit Low Voltage
DTC P0B56
- Hybrid Battery 6 Circuit Low Voltage
Wednesday, June 3, 2020
2010 Cadillac Truck Escalade RWD V8-6.2L Page 1355
2010 Cadillac Truck Escalade RWD V8-6.2L Page 1355
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
1. Ignition OFF, disable the high voltage at the drive motor generator battery. Refer to High Voltage Disabling ().
2. Disconnect the X4 harness connector at the drive motor battery control module.
3. Connect to the EL-48571 high voltage battery pin out box.
4. Install the high voltage manual disconnect lever. Measure and record each of the 20 battery voltages.
5. Each battery voltage reading should be between 10-19 V.
瀚慖f not within the specified range, replace the drive motor battery assembly.
6. Each battery voltage reading should be within 1.5 V of each other.
瀚慖f not within the specified range, replace the drive motor battery assembly.
7. If all circuits test normal, replace the drive motor battery control module.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the repair.
* Drive Motor Generator Battery Replacement and Shipping Preparation ()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for drive motor generator battery control module
replacement, setup and programming
P0B79
DTC P0B3D, P0B42, P0B47, P0B4C, P0B51, P0B56, P0B5B, P0B60, P0B65, P0B6A, P0B6F, P0B74, P0B79, P0B7E, P0B83, P0B88, P0B8D,
P0B92, P0B97, or P0B9C
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC P0B3D
- Hybrid Battery 1 Circuit Low Voltage
DTC P0B42
- Hybrid Battery 2 Circuit Low Voltage
DTC P0B47
- Hybrid Battery 3 Circuit Low Voltage
DTC P0B4C
- Hybrid Battery 4 Circuit Low Voltage
DTC P0B51
- Hybrid Battery 5 Circuit Low Voltage
DTC P0B56
- Hybrid Battery 6 Circuit Low Voltage
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
1. Ignition OFF, disable the high voltage at the drive motor generator battery. Refer to High Voltage Disabling ().
2. Disconnect the X4 harness connector at the drive motor battery control module.
3. Connect to the EL-48571 high voltage battery pin out box.
4. Install the high voltage manual disconnect lever. Measure and record each of the 20 battery voltages.
5. Each battery voltage reading should be between 10-19 V.
瀚慖f not within the specified range, replace the drive motor battery assembly.
6. Each battery voltage reading should be within 1.5 V of each other.
瀚慖f not within the specified range, replace the drive motor battery assembly.
7. If all circuits test normal, replace the drive motor battery control module.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the repair.
* Drive Motor Generator Battery Replacement and Shipping Preparation ()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for drive motor generator battery control module
replacement, setup and programming
P0B79
DTC P0B3D, P0B42, P0B47, P0B4C, P0B51, P0B56, P0B5B, P0B60, P0B65, P0B6A, P0B6F, P0B74, P0B79, P0B7E, P0B83, P0B88, P0B8D,
P0B92, P0B97, or P0B9C
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC P0B3D
- Hybrid Battery 1 Circuit Low Voltage
DTC P0B42
- Hybrid Battery 2 Circuit Low Voltage
DTC P0B47
- Hybrid Battery 3 Circuit Low Voltage
DTC P0B4C
- Hybrid Battery 4 Circuit Low Voltage
DTC P0B51
- Hybrid Battery 5 Circuit Low Voltage
DTC P0B56
- Hybrid Battery 6 Circuit Low Voltage
Sunday, May 31, 2020
2010 Cadillac Truck Escalade RWD V8-6.2L Page 1300
2010 Cadillac Truck Escalade RWD V8-6.2L Page 1300
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
1. Ignition OFF, disable the high voltage at the drive motor generator battery. Refer to High Voltage Disabling ().
2. Disconnect the X4 harness connector at the drive motor battery control module.
3. Connect to the EL-48571 high voltage battery pin out box.
4. Install the high voltage manual disconnect lever. Measure and record each of the 20 battery voltages.
5. Each battery voltage reading should be between 10-19 V.
瀚慖f not within the specified range, replace the drive motor battery assembly.
6. Each battery voltage reading should be within 1.5 V of each other.
瀚慖f not within the specified range, replace the drive motor battery assembly.
7. If all circuits test normal, replace the drive motor battery control module.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the repair.
* Drive Motor Generator Battery Replacement and Shipping Preparation ()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for drive motor generator battery control module
replacement, setup and programming
P0B47
DTC P0B3D, P0B42, P0B47, P0B4C, P0B51, P0B56, P0B5B, P0B60, P0B65, P0B6A, P0B6F, P0B74, P0B79, P0B7E, P0B83, P0B88, P0B8D,
P0B92, P0B97, or P0B9C
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC P0B3D
- Hybrid Battery 1 Circuit Low Voltage
DTC P0B42
- Hybrid Battery 2 Circuit Low Voltage
DTC P0B47
- Hybrid Battery 3 Circuit Low Voltage
DTC P0B4C
- Hybrid Battery 4 Circuit Low Voltage
DTC P0B51
- Hybrid Battery 5 Circuit Low Voltage
DTC P0B56
- Hybrid Battery 6 Circuit Low Voltage
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
1. Ignition OFF, disable the high voltage at the drive motor generator battery. Refer to High Voltage Disabling ().
2. Disconnect the X4 harness connector at the drive motor battery control module.
3. Connect to the EL-48571 high voltage battery pin out box.
4. Install the high voltage manual disconnect lever. Measure and record each of the 20 battery voltages.
5. Each battery voltage reading should be between 10-19 V.
瀚慖f not within the specified range, replace the drive motor battery assembly.
6. Each battery voltage reading should be within 1.5 V of each other.
瀚慖f not within the specified range, replace the drive motor battery assembly.
7. If all circuits test normal, replace the drive motor battery control module.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the repair.
* Drive Motor Generator Battery Replacement and Shipping Preparation ()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for drive motor generator battery control module
replacement, setup and programming
P0B47
DTC P0B3D, P0B42, P0B47, P0B4C, P0B51, P0B56, P0B5B, P0B60, P0B65, P0B6A, P0B6F, P0B74, P0B79, P0B7E, P0B83, P0B88, P0B8D,
P0B92, P0B97, or P0B9C
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC P0B3D
- Hybrid Battery 1 Circuit Low Voltage
DTC P0B42
- Hybrid Battery 2 Circuit Low Voltage
DTC P0B47
- Hybrid Battery 3 Circuit Low Voltage
DTC P0B4C
- Hybrid Battery 4 Circuit Low Voltage
DTC P0B51
- Hybrid Battery 5 Circuit Low Voltage
DTC P0B56
- Hybrid Battery 6 Circuit Low Voltage
Friday, May 29, 2020
2010 Cadillac Truck Escalade RWD V8-6.2L Page 1239
2010 Cadillac Truck Escalade RWD V8-6.2L Page 1239
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
1. Ignition OFF, disable the high voltage at the drive motor generator battery. Refer to High Voltage Disabling ().
2. Disconnect the X4 harness connector at the drive motor battery control module.
3. Connect to the EL-48571 high voltage battery pin out box.
4. Install the high voltage manual disconnect lever. Measure and record each of the 20 battery voltages.
5. Each battery voltage reading should be between 10-19 V.
瀚慖f not within the specified range, replace the drive motor battery assembly.
6. Each battery voltage reading should be within 1.5 V of each other.
瀚慖f not within the specified range, replace the drive motor battery assembly.
7. If all circuits test normal, replace the drive motor battery control module.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the repair.
* Drive Motor Generator Battery Replacement and Shipping Preparation ()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for drive motor generator battery control module
replacement, setup and programming
P0B5B
DTC P0B3D, P0B42, P0B47, P0B4C, P0B51, P0B56, P0B5B, P0B60, P0B65, P0B6A, P0B6F, P0B74, P0B79, P0B7E, P0B83, P0B88, P0B8D,
P0B92, P0B97, or P0B9C
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC P0B3D
- Hybrid Battery 1 Circuit Low Voltage
DTC P0B42
- Hybrid Battery 2 Circuit Low Voltage
DTC P0B47
- Hybrid Battery 3 Circuit Low Voltage
DTC P0B4C
- Hybrid Battery 4 Circuit Low Voltage
DTC P0B51
- Hybrid Battery 5 Circuit Low Voltage
DTC P0B56
- Hybrid Battery 6 Circuit Low Voltage
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
1. Ignition OFF, disable the high voltage at the drive motor generator battery. Refer to High Voltage Disabling ().
2. Disconnect the X4 harness connector at the drive motor battery control module.
3. Connect to the EL-48571 high voltage battery pin out box.
4. Install the high voltage manual disconnect lever. Measure and record each of the 20 battery voltages.
5. Each battery voltage reading should be between 10-19 V.
瀚慖f not within the specified range, replace the drive motor battery assembly.
6. Each battery voltage reading should be within 1.5 V of each other.
瀚慖f not within the specified range, replace the drive motor battery assembly.
7. If all circuits test normal, replace the drive motor battery control module.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the repair.
* Drive Motor Generator Battery Replacement and Shipping Preparation ()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for drive motor generator battery control module
replacement, setup and programming
P0B5B
DTC P0B3D, P0B42, P0B47, P0B4C, P0B51, P0B56, P0B5B, P0B60, P0B65, P0B6A, P0B6F, P0B74, P0B79, P0B7E, P0B83, P0B88, P0B8D,
P0B92, P0B97, or P0B9C
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC P0B3D
- Hybrid Battery 1 Circuit Low Voltage
DTC P0B42
- Hybrid Battery 2 Circuit Low Voltage
DTC P0B47
- Hybrid Battery 3 Circuit Low Voltage
DTC P0B4C
- Hybrid Battery 4 Circuit Low Voltage
DTC P0B51
- Hybrid Battery 5 Circuit Low Voltage
DTC P0B56
- Hybrid Battery 6 Circuit Low Voltage
Wednesday, March 18, 2020
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 3135
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 3135
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
Note: Use the schematic to identify the following:
* Control modules the vehicle is equipped with
* Control module locations on the low and high speed GMLAN serial data circuits
* The control modules B+, ignition, ground, communication enable and serial data circuit terminals
1. Determine the control module that is not communicating. Refer to Control Module U Code List (See: Diagnostic Trouble Code
Descriptions/Control Module U Code List).
2. Using the Hybrid High Voltage Module Chart below, verify that the non-communicating control module is not a high voltage module. If the
control module is a high voltage module, perform the High Voltage Disabling (See: Hybrid Drive Systems/Battery System, Hybrid
Drive/Testing and Inspection/Initial Inspection and Diagnostic Overview/High Voltage Disabling) procedure before proceeding with this
diagnostic.
3. If high voltage disabling is required, reconnect the 12 V battery after performing the high voltage disabling procedure.
4. Ignition OFF, disconnect the harness connector of the control module that is not communicating.
5. Test for less than 10 ohm between each ground circuit terminal and ground.
瀚慖f greater than the specified range, test the ground circuit for an open/high resistance.
6. If equipped, verify that a test lamp illuminates between each B+ circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test the
control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
7. If equipped, ignition ON, verify that a test lamp illuminates between each ignition circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test
the control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
Note: Only the high speed GMLAN modules have a serial data communication enable circuit OR an accessory wakeup serial data circuit,
and the BCM is the output for these circuits. Refer to the module schematics to identify which modules have these circuits.
8. If equipped, ignition ON, verify that a test lamp illuminates between the communication enable circuit terminal OR the accessory wakeup
circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the circuit for an open/high resistance. If the circuits test normal, replace the BCM.
9. Ignition OFF for 60 seconds, test for less than 5 ohm between the serial data circuit terminals and the appropriate DLC terminal listed below:
* Class 2 serial data circuit terminal 2
* Low speed GMLAN serial data terminal 1
* High speed GMLAN serial data terminal 6 or 14
瀚慖f greater than the specified range, test the serial data circuit for an open/high resistance between the non communicating control module
and a control module setting the DTC or a serial data splice pack.
10. If all circuits test normal, replace the control module that is not communicating.
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
Note: Use the schematic to identify the following:
* Control modules the vehicle is equipped with
* Control module locations on the low and high speed GMLAN serial data circuits
* The control modules B+, ignition, ground, communication enable and serial data circuit terminals
1. Determine the control module that is not communicating. Refer to Control Module U Code List (See: Diagnostic Trouble Code
Descriptions/Control Module U Code List).
2. Using the Hybrid High Voltage Module Chart below, verify that the non-communicating control module is not a high voltage module. If the
control module is a high voltage module, perform the High Voltage Disabling (See: Hybrid Drive Systems/Battery System, Hybrid
Drive/Testing and Inspection/Initial Inspection and Diagnostic Overview/High Voltage Disabling) procedure before proceeding with this
diagnostic.
3. If high voltage disabling is required, reconnect the 12 V battery after performing the high voltage disabling procedure.
4. Ignition OFF, disconnect the harness connector of the control module that is not communicating.
5. Test for less than 10 ohm between each ground circuit terminal and ground.
瀚慖f greater than the specified range, test the ground circuit for an open/high resistance.
6. If equipped, verify that a test lamp illuminates between each B+ circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test the
control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
7. If equipped, ignition ON, verify that a test lamp illuminates between each ignition circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test
the control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
Note: Only the high speed GMLAN modules have a serial data communication enable circuit OR an accessory wakeup serial data circuit,
and the BCM is the output for these circuits. Refer to the module schematics to identify which modules have these circuits.
8. If equipped, ignition ON, verify that a test lamp illuminates between the communication enable circuit terminal OR the accessory wakeup
circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the circuit for an open/high resistance. If the circuits test normal, replace the BCM.
9. Ignition OFF for 60 seconds, test for less than 5 ohm between the serial data circuit terminals and the appropriate DLC terminal listed below:
* Class 2 serial data circuit terminal 2
* Low speed GMLAN serial data terminal 1
* High speed GMLAN serial data terminal 6 or 14
瀚慖f greater than the specified range, test the serial data circuit for an open/high resistance between the non communicating control module
and a control module setting the DTC or a serial data splice pack.
10. If all circuits test normal, replace the control module that is not communicating.
Tuesday, March 17, 2020
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 3128
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 3128
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
Note: Use the schematic to identify the following:
* Control modules the vehicle is equipped with
* Control module locations on the low and high speed GMLAN serial data circuits
* The control modules B+, ignition, ground, communication enable and serial data circuit terminals
1. Determine the control module that is not communicating. Refer to Control Module U Code List (See: Diagnostic Trouble Code
Descriptions/Control Module U Code List).
2. Using the Hybrid High Voltage Module Chart below, verify that the non-communicating control module is not a high voltage module. If the
control module is a high voltage module, perform the High Voltage Disabling (See: Hybrid Drive Systems/Battery System, Hybrid
Drive/Testing and Inspection/Initial Inspection and Diagnostic Overview/High Voltage Disabling) procedure before proceeding with this
diagnostic.
3. If high voltage disabling is required, reconnect the 12 V battery after performing the high voltage disabling procedure.
4. Ignition OFF, disconnect the harness connector of the control module that is not communicating.
5. Test for less than 10 ohm between each ground circuit terminal and ground.
瀚慖f greater than the specified range, test the ground circuit for an open/high resistance.
6. If equipped, verify that a test lamp illuminates between each B+ circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test the
control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
7. If equipped, ignition ON, verify that a test lamp illuminates between each ignition circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test
the control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
Note: Only the high speed GMLAN modules have a serial data communication enable circuit OR an accessory wakeup serial data circuit,
and the BCM is the output for these circuits. Refer to the module schematics to identify which modules have these circuits.
8. If equipped, ignition ON, verify that a test lamp illuminates between the communication enable circuit terminal OR the accessory wakeup
circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the circuit for an open/high resistance. If the circuits test normal, replace the BCM.
9. Ignition OFF for 60 seconds, test for less than 5 ohm between the serial data circuit terminals and the appropriate DLC terminal listed below:
* Class 2 serial data circuit terminal 2
* Low speed GMLAN serial data terminal 1
* High speed GMLAN serial data terminal 6 or 14
瀚慖f greater than the specified range, test the serial data circuit for an open/high resistance between the non communicating control module
and a control module setting the DTC or a serial data splice pack.
10. If all circuits test normal, replace the control module that is not communicating.
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
Note: Use the schematic to identify the following:
* Control modules the vehicle is equipped with
* Control module locations on the low and high speed GMLAN serial data circuits
* The control modules B+, ignition, ground, communication enable and serial data circuit terminals
1. Determine the control module that is not communicating. Refer to Control Module U Code List (See: Diagnostic Trouble Code
Descriptions/Control Module U Code List).
2. Using the Hybrid High Voltage Module Chart below, verify that the non-communicating control module is not a high voltage module. If the
control module is a high voltage module, perform the High Voltage Disabling (See: Hybrid Drive Systems/Battery System, Hybrid
Drive/Testing and Inspection/Initial Inspection and Diagnostic Overview/High Voltage Disabling) procedure before proceeding with this
diagnostic.
3. If high voltage disabling is required, reconnect the 12 V battery after performing the high voltage disabling procedure.
4. Ignition OFF, disconnect the harness connector of the control module that is not communicating.
5. Test for less than 10 ohm between each ground circuit terminal and ground.
瀚慖f greater than the specified range, test the ground circuit for an open/high resistance.
6. If equipped, verify that a test lamp illuminates between each B+ circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test the
control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
7. If equipped, ignition ON, verify that a test lamp illuminates between each ignition circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test
the control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
Note: Only the high speed GMLAN modules have a serial data communication enable circuit OR an accessory wakeup serial data circuit,
and the BCM is the output for these circuits. Refer to the module schematics to identify which modules have these circuits.
8. If equipped, ignition ON, verify that a test lamp illuminates between the communication enable circuit terminal OR the accessory wakeup
circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the circuit for an open/high resistance. If the circuits test normal, replace the BCM.
9. Ignition OFF for 60 seconds, test for less than 5 ohm between the serial data circuit terminals and the appropriate DLC terminal listed below:
* Class 2 serial data circuit terminal 2
* Low speed GMLAN serial data terminal 1
* High speed GMLAN serial data terminal 6 or 14
瀚慖f greater than the specified range, test the serial data circuit for an open/high resistance between the non communicating control module
and a control module setting the DTC or a serial data splice pack.
10. If all circuits test normal, replace the control module that is not communicating.
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 3121
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 3121
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
Note: Use the schematic to identify the following:
* Control modules the vehicle is equipped with
* Control module locations on the low and high speed GMLAN serial data circuits
* The control modules B+, ignition, ground, communication enable and serial data circuit terminals
1. Determine the control module that is not communicating. Refer to Control Module U Code List (See: Diagnostic Trouble Code
Descriptions/Control Module U Code List).
2. Using the Hybrid High Voltage Module Chart below, verify that the non-communicating control module is not a high voltage module. If the
control module is a high voltage module, perform the High Voltage Disabling (See: Hybrid Drive Systems/Battery System, Hybrid
Drive/Testing and Inspection/Initial Inspection and Diagnostic Overview/High Voltage Disabling) procedure before proceeding with this
diagnostic.
3. If high voltage disabling is required, reconnect the 12 V battery after performing the high voltage disabling procedure.
4. Ignition OFF, disconnect the harness connector of the control module that is not communicating.
5. Test for less than 10 ohm between each ground circuit terminal and ground.
瀚慖f greater than the specified range, test the ground circuit for an open/high resistance.
6. If equipped, verify that a test lamp illuminates between each B+ circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test the
control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
7. If equipped, ignition ON, verify that a test lamp illuminates between each ignition circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test
the control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
Note: Only the high speed GMLAN modules have a serial data communication enable circuit OR an accessory wakeup serial data circuit,
and the BCM is the output for these circuits. Refer to the module schematics to identify which modules have these circuits.
8. If equipped, ignition ON, verify that a test lamp illuminates between the communication enable circuit terminal OR the accessory wakeup
circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the circuit for an open/high resistance. If the circuits test normal, replace the BCM.
9. Ignition OFF for 60 seconds, test for less than 5 ohm between the serial data circuit terminals and the appropriate DLC terminal listed below:
* Class 2 serial data circuit terminal 2
* Low speed GMLAN serial data terminal 1
* High speed GMLAN serial data terminal 6 or 14
瀚慖f greater than the specified range, test the serial data circuit for an open/high resistance between the non communicating control module
and a control module setting the DTC or a serial data splice pack.
10. If all circuits test normal, replace the control module that is not communicating.
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
Note: Use the schematic to identify the following:
* Control modules the vehicle is equipped with
* Control module locations on the low and high speed GMLAN serial data circuits
* The control modules B+, ignition, ground, communication enable and serial data circuit terminals
1. Determine the control module that is not communicating. Refer to Control Module U Code List (See: Diagnostic Trouble Code
Descriptions/Control Module U Code List).
2. Using the Hybrid High Voltage Module Chart below, verify that the non-communicating control module is not a high voltage module. If the
control module is a high voltage module, perform the High Voltage Disabling (See: Hybrid Drive Systems/Battery System, Hybrid
Drive/Testing and Inspection/Initial Inspection and Diagnostic Overview/High Voltage Disabling) procedure before proceeding with this
diagnostic.
3. If high voltage disabling is required, reconnect the 12 V battery after performing the high voltage disabling procedure.
4. Ignition OFF, disconnect the harness connector of the control module that is not communicating.
5. Test for less than 10 ohm between each ground circuit terminal and ground.
瀚慖f greater than the specified range, test the ground circuit for an open/high resistance.
6. If equipped, verify that a test lamp illuminates between each B+ circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test the
control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
7. If equipped, ignition ON, verify that a test lamp illuminates between each ignition circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test
the control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
Note: Only the high speed GMLAN modules have a serial data communication enable circuit OR an accessory wakeup serial data circuit,
and the BCM is the output for these circuits. Refer to the module schematics to identify which modules have these circuits.
8. If equipped, ignition ON, verify that a test lamp illuminates between the communication enable circuit terminal OR the accessory wakeup
circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the circuit for an open/high resistance. If the circuits test normal, replace the BCM.
9. Ignition OFF for 60 seconds, test for less than 5 ohm between the serial data circuit terminals and the appropriate DLC terminal listed below:
* Class 2 serial data circuit terminal 2
* Low speed GMLAN serial data terminal 1
* High speed GMLAN serial data terminal 6 or 14
瀚慖f greater than the specified range, test the serial data circuit for an open/high resistance between the non communicating control module
and a control module setting the DTC or a serial data splice pack.
10. If all circuits test normal, replace the control module that is not communicating.
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 3114
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 3114
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
Note: Use the schematic to identify the following:
* Control modules the vehicle is equipped with
* Control module locations on the low and high speed GMLAN serial data circuits
* The control modules B+, ignition, ground, communication enable and serial data circuit terminals
1. Determine the control module that is not communicating. Refer to Control Module U Code List (See: Diagnostic Trouble Code
Descriptions/Control Module U Code List).
2. Using the Hybrid High Voltage Module Chart below, verify that the non-communicating control module is not a high voltage module. If the
control module is a high voltage module, perform the High Voltage Disabling (See: Hybrid Drive Systems/Battery System, Hybrid
Drive/Testing and Inspection/Initial Inspection and Diagnostic Overview/High Voltage Disabling) procedure before proceeding with this
diagnostic.
3. If high voltage disabling is required, reconnect the 12 V battery after performing the high voltage disabling procedure.
4. Ignition OFF, disconnect the harness connector of the control module that is not communicating.
5. Test for less than 10 ohm between each ground circuit terminal and ground.
瀚慖f greater than the specified range, test the ground circuit for an open/high resistance.
6. If equipped, verify that a test lamp illuminates between each B+ circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test the
control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
7. If equipped, ignition ON, verify that a test lamp illuminates between each ignition circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test
the control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
Note: Only the high speed GMLAN modules have a serial data communication enable circuit OR an accessory wakeup serial data circuit,
and the BCM is the output for these circuits. Refer to the module schematics to identify which modules have these circuits.
8. If equipped, ignition ON, verify that a test lamp illuminates between the communication enable circuit terminal OR the accessory wakeup
circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the circuit for an open/high resistance. If the circuits test normal, replace the BCM.
9. Ignition OFF for 60 seconds, test for less than 5 ohm between the serial data circuit terminals and the appropriate DLC terminal listed below:
* Class 2 serial data circuit terminal 2
* Low speed GMLAN serial data terminal 1
* High speed GMLAN serial data terminal 6 or 14
瀚慖f greater than the specified range, test the serial data circuit for an open/high resistance between the non communicating control module
and a control module setting the DTC or a serial data splice pack.
10. If all circuits test normal, replace the control module that is not communicating.
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
Note: Use the schematic to identify the following:
* Control modules the vehicle is equipped with
* Control module locations on the low and high speed GMLAN serial data circuits
* The control modules B+, ignition, ground, communication enable and serial data circuit terminals
1. Determine the control module that is not communicating. Refer to Control Module U Code List (See: Diagnostic Trouble Code
Descriptions/Control Module U Code List).
2. Using the Hybrid High Voltage Module Chart below, verify that the non-communicating control module is not a high voltage module. If the
control module is a high voltage module, perform the High Voltage Disabling (See: Hybrid Drive Systems/Battery System, Hybrid
Drive/Testing and Inspection/Initial Inspection and Diagnostic Overview/High Voltage Disabling) procedure before proceeding with this
diagnostic.
3. If high voltage disabling is required, reconnect the 12 V battery after performing the high voltage disabling procedure.
4. Ignition OFF, disconnect the harness connector of the control module that is not communicating.
5. Test for less than 10 ohm between each ground circuit terminal and ground.
瀚慖f greater than the specified range, test the ground circuit for an open/high resistance.
6. If equipped, verify that a test lamp illuminates between each B+ circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test the
control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
7. If equipped, ignition ON, verify that a test lamp illuminates between each ignition circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test
the control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
Note: Only the high speed GMLAN modules have a serial data communication enable circuit OR an accessory wakeup serial data circuit,
and the BCM is the output for these circuits. Refer to the module schematics to identify which modules have these circuits.
8. If equipped, ignition ON, verify that a test lamp illuminates between the communication enable circuit terminal OR the accessory wakeup
circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the circuit for an open/high resistance. If the circuits test normal, replace the BCM.
9. Ignition OFF for 60 seconds, test for less than 5 ohm between the serial data circuit terminals and the appropriate DLC terminal listed below:
* Class 2 serial data circuit terminal 2
* Low speed GMLAN serial data terminal 1
* High speed GMLAN serial data terminal 6 or 14
瀚慖f greater than the specified range, test the serial data circuit for an open/high resistance between the non communicating control module
and a control module setting the DTC or a serial data splice pack.
10. If all circuits test normal, replace the control module that is not communicating.
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 3107
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 3107
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
Note: Use the schematic to identify the following:
* Control modules the vehicle is equipped with
* Control module locations on the low and high speed GMLAN serial data circuits
* The control modules B+, ignition, ground, communication enable and serial data circuit terminals
1. Determine the control module that is not communicating. Refer to Control Module U Code List (See: Diagnostic Trouble Code
Descriptions/Control Module U Code List).
2. Using the Hybrid High Voltage Module Chart below, verify that the non-communicating control module is not a high voltage module. If the
control module is a high voltage module, perform the High Voltage Disabling (See: Hybrid Drive Systems/Battery System, Hybrid
Drive/Testing and Inspection/Initial Inspection and Diagnostic Overview/High Voltage Disabling) procedure before proceeding with this
diagnostic.
3. If high voltage disabling is required, reconnect the 12 V battery after performing the high voltage disabling procedure.
4. Ignition OFF, disconnect the harness connector of the control module that is not communicating.
5. Test for less than 10 ohm between each ground circuit terminal and ground.
瀚慖f greater than the specified range, test the ground circuit for an open/high resistance.
6. If equipped, verify that a test lamp illuminates between each B+ circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test the
control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
7. If equipped, ignition ON, verify that a test lamp illuminates between each ignition circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test
the control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
Note: Only the high speed GMLAN modules have a serial data communication enable circuit OR an accessory wakeup serial data circuit,
and the BCM is the output for these circuits. Refer to the module schematics to identify which modules have these circuits.
8. If equipped, ignition ON, verify that a test lamp illuminates between the communication enable circuit terminal OR the accessory wakeup
circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the circuit for an open/high resistance. If the circuits test normal, replace the BCM.
9. Ignition OFF for 60 seconds, test for less than 5 ohm between the serial data circuit terminals and the appropriate DLC terminal listed below:
* Class 2 serial data circuit terminal 2
* Low speed GMLAN serial data terminal 1
* High speed GMLAN serial data terminal 6 or 14
瀚慖f greater than the specified range, test the serial data circuit for an open/high resistance between the non communicating control module
and a control module setting the DTC or a serial data splice pack.
10. If all circuits test normal, replace the control module that is not communicating.
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
Note: Use the schematic to identify the following:
* Control modules the vehicle is equipped with
* Control module locations on the low and high speed GMLAN serial data circuits
* The control modules B+, ignition, ground, communication enable and serial data circuit terminals
1. Determine the control module that is not communicating. Refer to Control Module U Code List (See: Diagnostic Trouble Code
Descriptions/Control Module U Code List).
2. Using the Hybrid High Voltage Module Chart below, verify that the non-communicating control module is not a high voltage module. If the
control module is a high voltage module, perform the High Voltage Disabling (See: Hybrid Drive Systems/Battery System, Hybrid
Drive/Testing and Inspection/Initial Inspection and Diagnostic Overview/High Voltage Disabling) procedure before proceeding with this
diagnostic.
3. If high voltage disabling is required, reconnect the 12 V battery after performing the high voltage disabling procedure.
4. Ignition OFF, disconnect the harness connector of the control module that is not communicating.
5. Test for less than 10 ohm between each ground circuit terminal and ground.
瀚慖f greater than the specified range, test the ground circuit for an open/high resistance.
6. If equipped, verify that a test lamp illuminates between each B+ circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test the
control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
7. If equipped, ignition ON, verify that a test lamp illuminates between each ignition circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test
the control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
Note: Only the high speed GMLAN modules have a serial data communication enable circuit OR an accessory wakeup serial data circuit,
and the BCM is the output for these circuits. Refer to the module schematics to identify which modules have these circuits.
8. If equipped, ignition ON, verify that a test lamp illuminates between the communication enable circuit terminal OR the accessory wakeup
circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the circuit for an open/high resistance. If the circuits test normal, replace the BCM.
9. Ignition OFF for 60 seconds, test for less than 5 ohm between the serial data circuit terminals and the appropriate DLC terminal listed below:
* Class 2 serial data circuit terminal 2
* Low speed GMLAN serial data terminal 1
* High speed GMLAN serial data terminal 6 or 14
瀚慖f greater than the specified range, test the serial data circuit for an open/high resistance between the non communicating control module
and a control module setting the DTC or a serial data splice pack.
10. If all circuits test normal, replace the control module that is not communicating.
Monday, March 16, 2020
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 3100
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 3100
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
Note: Use the schematic to identify the following:
* Control modules the vehicle is equipped with
* Control module locations on the low and high speed GMLAN serial data circuits
* The control modules B+, ignition, ground, communication enable and serial data circuit terminals
1. Determine the control module that is not communicating. Refer to Control Module U Code List (See: Diagnostic Trouble Code
Descriptions/Control Module U Code List).
2. Using the Hybrid High Voltage Module Chart below, verify that the non-communicating control module is not a high voltage module. If the
control module is a high voltage module, perform the High Voltage Disabling (See: Hybrid Drive Systems/Battery System, Hybrid
Drive/Testing and Inspection/Initial Inspection and Diagnostic Overview/High Voltage Disabling) procedure before proceeding with this
diagnostic.
3. If high voltage disabling is required, reconnect the 12 V battery after performing the high voltage disabling procedure.
4. Ignition OFF, disconnect the harness connector of the control module that is not communicating.
5. Test for less than 10 ohm between each ground circuit terminal and ground.
瀚慖f greater than the specified range, test the ground circuit for an open/high resistance.
6. If equipped, verify that a test lamp illuminates between each B+ circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test the
control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
7. If equipped, ignition ON, verify that a test lamp illuminates between each ignition circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test
the control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
Note: Only the high speed GMLAN modules have a serial data communication enable circuit OR an accessory wakeup serial data circuit,
and the BCM is the output for these circuits. Refer to the module schematics to identify which modules have these circuits.
8. If equipped, ignition ON, verify that a test lamp illuminates between the communication enable circuit terminal OR the accessory wakeup
circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the circuit for an open/high resistance. If the circuits test normal, replace the BCM.
9. Ignition OFF for 60 seconds, test for less than 5 ohm between the serial data circuit terminals and the appropriate DLC terminal listed below:
* Class 2 serial data circuit terminal 2
* Low speed GMLAN serial data terminal 1
* High speed GMLAN serial data terminal 6 or 14
瀚慖f greater than the specified range, test the serial data circuit for an open/high resistance between the non communicating control module
and a control module setting the DTC or a serial data splice pack.
10. If all circuits test normal, replace the control module that is not communicating.
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
Note: Use the schematic to identify the following:
* Control modules the vehicle is equipped with
* Control module locations on the low and high speed GMLAN serial data circuits
* The control modules B+, ignition, ground, communication enable and serial data circuit terminals
1. Determine the control module that is not communicating. Refer to Control Module U Code List (See: Diagnostic Trouble Code
Descriptions/Control Module U Code List).
2. Using the Hybrid High Voltage Module Chart below, verify that the non-communicating control module is not a high voltage module. If the
control module is a high voltage module, perform the High Voltage Disabling (See: Hybrid Drive Systems/Battery System, Hybrid
Drive/Testing and Inspection/Initial Inspection and Diagnostic Overview/High Voltage Disabling) procedure before proceeding with this
diagnostic.
3. If high voltage disabling is required, reconnect the 12 V battery after performing the high voltage disabling procedure.
4. Ignition OFF, disconnect the harness connector of the control module that is not communicating.
5. Test for less than 10 ohm between each ground circuit terminal and ground.
瀚慖f greater than the specified range, test the ground circuit for an open/high resistance.
6. If equipped, verify that a test lamp illuminates between each B+ circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test the
control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
7. If equipped, ignition ON, verify that a test lamp illuminates between each ignition circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test
the control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
Note: Only the high speed GMLAN modules have a serial data communication enable circuit OR an accessory wakeup serial data circuit,
and the BCM is the output for these circuits. Refer to the module schematics to identify which modules have these circuits.
8. If equipped, ignition ON, verify that a test lamp illuminates between the communication enable circuit terminal OR the accessory wakeup
circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the circuit for an open/high resistance. If the circuits test normal, replace the BCM.
9. Ignition OFF for 60 seconds, test for less than 5 ohm between the serial data circuit terminals and the appropriate DLC terminal listed below:
* Class 2 serial data circuit terminal 2
* Low speed GMLAN serial data terminal 1
* High speed GMLAN serial data terminal 6 or 14
瀚慖f greater than the specified range, test the serial data circuit for an open/high resistance between the non communicating control module
and a control module setting the DTC or a serial data splice pack.
10. If all circuits test normal, replace the control module that is not communicating.
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 3093
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 3093
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
Note: Use the schematic to identify the following:
* Control modules the vehicle is equipped with
* Control module locations on the low and high speed GMLAN serial data circuits
* The control modules B+, ignition, ground, communication enable and serial data circuit terminals
1. Determine the control module that is not communicating. Refer to Control Module U Code List (See: Diagnostic Trouble Code
Descriptions/Control Module U Code List).
2. Using the Hybrid High Voltage Module Chart below, verify that the non-communicating control module is not a high voltage module. If the
control module is a high voltage module, perform the High Voltage Disabling (See: Hybrid Drive Systems/Battery System, Hybrid
Drive/Testing and Inspection/Initial Inspection and Diagnostic Overview/High Voltage Disabling) procedure before proceeding with this
diagnostic.
3. If high voltage disabling is required, reconnect the 12 V battery after performing the high voltage disabling procedure.
4. Ignition OFF, disconnect the harness connector of the control module that is not communicating.
5. Test for less than 10 ohm between each ground circuit terminal and ground.
瀚慖f greater than the specified range, test the ground circuit for an open/high resistance.
6. If equipped, verify that a test lamp illuminates between each B+ circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test the
control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
7. If equipped, ignition ON, verify that a test lamp illuminates between each ignition circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test
the control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
Note: Only the high speed GMLAN modules have a serial data communication enable circuit OR an accessory wakeup serial data circuit,
and the BCM is the output for these circuits. Refer to the module schematics to identify which modules have these circuits.
8. If equipped, ignition ON, verify that a test lamp illuminates between the communication enable circuit terminal OR the accessory wakeup
circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the circuit for an open/high resistance. If the circuits test normal, replace the BCM.
9. Ignition OFF for 60 seconds, test for less than 5 ohm between the serial data circuit terminals and the appropriate DLC terminal listed below:
* Class 2 serial data circuit terminal 2
* Low speed GMLAN serial data terminal 1
* High speed GMLAN serial data terminal 6 or 14
瀚慖f greater than the specified range, test the serial data circuit for an open/high resistance between the non communicating control module
and a control module setting the DTC or a serial data splice pack.
10. If all circuits test normal, replace the control module that is not communicating.
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
Note: Use the schematic to identify the following:
* Control modules the vehicle is equipped with
* Control module locations on the low and high speed GMLAN serial data circuits
* The control modules B+, ignition, ground, communication enable and serial data circuit terminals
1. Determine the control module that is not communicating. Refer to Control Module U Code List (See: Diagnostic Trouble Code
Descriptions/Control Module U Code List).
2. Using the Hybrid High Voltage Module Chart below, verify that the non-communicating control module is not a high voltage module. If the
control module is a high voltage module, perform the High Voltage Disabling (See: Hybrid Drive Systems/Battery System, Hybrid
Drive/Testing and Inspection/Initial Inspection and Diagnostic Overview/High Voltage Disabling) procedure before proceeding with this
diagnostic.
3. If high voltage disabling is required, reconnect the 12 V battery after performing the high voltage disabling procedure.
4. Ignition OFF, disconnect the harness connector of the control module that is not communicating.
5. Test for less than 10 ohm between each ground circuit terminal and ground.
瀚慖f greater than the specified range, test the ground circuit for an open/high resistance.
6. If equipped, verify that a test lamp illuminates between each B+ circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test the
control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
7. If equipped, ignition ON, verify that a test lamp illuminates between each ignition circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test
the control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
Note: Only the high speed GMLAN modules have a serial data communication enable circuit OR an accessory wakeup serial data circuit,
and the BCM is the output for these circuits. Refer to the module schematics to identify which modules have these circuits.
8. If equipped, ignition ON, verify that a test lamp illuminates between the communication enable circuit terminal OR the accessory wakeup
circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the circuit for an open/high resistance. If the circuits test normal, replace the BCM.
9. Ignition OFF for 60 seconds, test for less than 5 ohm between the serial data circuit terminals and the appropriate DLC terminal listed below:
* Class 2 serial data circuit terminal 2
* Low speed GMLAN serial data terminal 1
* High speed GMLAN serial data terminal 6 or 14
瀚慖f greater than the specified range, test the serial data circuit for an open/high resistance between the non communicating control module
and a control module setting the DTC or a serial data splice pack.
10. If all circuits test normal, replace the control module that is not communicating.
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 3086
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 3086
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
Note: Use the schematic to identify the following:
* Control modules the vehicle is equipped with
* Control module locations on the low and high speed GMLAN serial data circuits
* The control modules B+, ignition, ground, communication enable and serial data circuit terminals
1. Determine the control module that is not communicating. Refer to Control Module U Code List (See: Diagnostic Trouble Code
Descriptions/Control Module U Code List).
2. Using the Hybrid High Voltage Module Chart below, verify that the non-communicating control module is not a high voltage module. If the
control module is a high voltage module, perform the High Voltage Disabling (See: Hybrid Drive Systems/Battery System, Hybrid
Drive/Testing and Inspection/Initial Inspection and Diagnostic Overview/High Voltage Disabling) procedure before proceeding with this
diagnostic.
3. If high voltage disabling is required, reconnect the 12 V battery after performing the high voltage disabling procedure.
4. Ignition OFF, disconnect the harness connector of the control module that is not communicating.
5. Test for less than 10 ohm between each ground circuit terminal and ground.
瀚慖f greater than the specified range, test the ground circuit for an open/high resistance.
6. If equipped, verify that a test lamp illuminates between each B+ circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test the
control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
7. If equipped, ignition ON, verify that a test lamp illuminates between each ignition circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test
the control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
Note: Only the high speed GMLAN modules have a serial data communication enable circuit OR an accessory wakeup serial data circuit,
and the BCM is the output for these circuits. Refer to the module schematics to identify which modules have these circuits.
8. If equipped, ignition ON, verify that a test lamp illuminates between the communication enable circuit terminal OR the accessory wakeup
circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the circuit for an open/high resistance. If the circuits test normal, replace the BCM.
9. Ignition OFF for 60 seconds, test for less than 5 ohm between the serial data circuit terminals and the appropriate DLC terminal listed below:
* Class 2 serial data circuit terminal 2
* Low speed GMLAN serial data terminal 1
* High speed GMLAN serial data terminal 6 or 14
瀚慖f greater than the specified range, test the serial data circuit for an open/high resistance between the non communicating control module
and a control module setting the DTC or a serial data splice pack.
10. If all circuits test normal, replace the control module that is not communicating.
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
Note: Use the schematic to identify the following:
* Control modules the vehicle is equipped with
* Control module locations on the low and high speed GMLAN serial data circuits
* The control modules B+, ignition, ground, communication enable and serial data circuit terminals
1. Determine the control module that is not communicating. Refer to Control Module U Code List (See: Diagnostic Trouble Code
Descriptions/Control Module U Code List).
2. Using the Hybrid High Voltage Module Chart below, verify that the non-communicating control module is not a high voltage module. If the
control module is a high voltage module, perform the High Voltage Disabling (See: Hybrid Drive Systems/Battery System, Hybrid
Drive/Testing and Inspection/Initial Inspection and Diagnostic Overview/High Voltage Disabling) procedure before proceeding with this
diagnostic.
3. If high voltage disabling is required, reconnect the 12 V battery after performing the high voltage disabling procedure.
4. Ignition OFF, disconnect the harness connector of the control module that is not communicating.
5. Test for less than 10 ohm between each ground circuit terminal and ground.
瀚慖f greater than the specified range, test the ground circuit for an open/high resistance.
6. If equipped, verify that a test lamp illuminates between each B+ circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test the
control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
7. If equipped, ignition ON, verify that a test lamp illuminates between each ignition circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test
the control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
Note: Only the high speed GMLAN modules have a serial data communication enable circuit OR an accessory wakeup serial data circuit,
and the BCM is the output for these circuits. Refer to the module schematics to identify which modules have these circuits.
8. If equipped, ignition ON, verify that a test lamp illuminates between the communication enable circuit terminal OR the accessory wakeup
circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the circuit for an open/high resistance. If the circuits test normal, replace the BCM.
9. Ignition OFF for 60 seconds, test for less than 5 ohm between the serial data circuit terminals and the appropriate DLC terminal listed below:
* Class 2 serial data circuit terminal 2
* Low speed GMLAN serial data terminal 1
* High speed GMLAN serial data terminal 6 or 14
瀚慖f greater than the specified range, test the serial data circuit for an open/high resistance between the non communicating control module
and a control module setting the DTC or a serial data splice pack.
10. If all circuits test normal, replace the control module that is not communicating.
Sunday, March 15, 2020
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 3079
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 3079
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
Note: Use the schematic to identify the following:
* Control modules the vehicle is equipped with
* Control module locations on the low and high speed GMLAN serial data circuits
* The control modules B+, ignition, ground, communication enable and serial data circuit terminals
1. Determine the control module that is not communicating. Refer to Control Module U Code List (See: Diagnostic Trouble Code
Descriptions/Control Module U Code List).
2. Using the Hybrid High Voltage Module Chart below, verify that the non-communicating control module is not a high voltage module. If the
control module is a high voltage module, perform the High Voltage Disabling (See: Hybrid Drive Systems/Battery System, Hybrid
Drive/Testing and Inspection/Initial Inspection and Diagnostic Overview/High Voltage Disabling) procedure before proceeding with this
diagnostic.
3. If high voltage disabling is required, reconnect the 12 V battery after performing the high voltage disabling procedure.
4. Ignition OFF, disconnect the harness connector of the control module that is not communicating.
5. Test for less than 10 ohm between each ground circuit terminal and ground.
瀚慖f greater than the specified range, test the ground circuit for an open/high resistance.
6. If equipped, verify that a test lamp illuminates between each B+ circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test the
control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
7. If equipped, ignition ON, verify that a test lamp illuminates between each ignition circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test
the control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
Note: Only the high speed GMLAN modules have a serial data communication enable circuit OR an accessory wakeup serial data circuit,
and the BCM is the output for these circuits. Refer to the module schematics to identify which modules have these circuits.
8. If equipped, ignition ON, verify that a test lamp illuminates between the communication enable circuit terminal OR the accessory wakeup
circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the circuit for an open/high resistance. If the circuits test normal, replace the BCM.
9. Ignition OFF for 60 seconds, test for less than 5 ohm between the serial data circuit terminals and the appropriate DLC terminal listed below:
* Class 2 serial data circuit terminal 2
* Low speed GMLAN serial data terminal 1
* High speed GMLAN serial data terminal 6 or 14
瀚慖f greater than the specified range, test the serial data circuit for an open/high resistance between the non communicating control module
and a control module setting the DTC or a serial data splice pack.
10. If all circuits test normal, replace the control module that is not communicating.
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
Note: Use the schematic to identify the following:
* Control modules the vehicle is equipped with
* Control module locations on the low and high speed GMLAN serial data circuits
* The control modules B+, ignition, ground, communication enable and serial data circuit terminals
1. Determine the control module that is not communicating. Refer to Control Module U Code List (See: Diagnostic Trouble Code
Descriptions/Control Module U Code List).
2. Using the Hybrid High Voltage Module Chart below, verify that the non-communicating control module is not a high voltage module. If the
control module is a high voltage module, perform the High Voltage Disabling (See: Hybrid Drive Systems/Battery System, Hybrid
Drive/Testing and Inspection/Initial Inspection and Diagnostic Overview/High Voltage Disabling) procedure before proceeding with this
diagnostic.
3. If high voltage disabling is required, reconnect the 12 V battery after performing the high voltage disabling procedure.
4. Ignition OFF, disconnect the harness connector of the control module that is not communicating.
5. Test for less than 10 ohm between each ground circuit terminal and ground.
瀚慖f greater than the specified range, test the ground circuit for an open/high resistance.
6. If equipped, verify that a test lamp illuminates between each B+ circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test the
control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
7. If equipped, ignition ON, verify that a test lamp illuminates between each ignition circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test
the control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
Note: Only the high speed GMLAN modules have a serial data communication enable circuit OR an accessory wakeup serial data circuit,
and the BCM is the output for these circuits. Refer to the module schematics to identify which modules have these circuits.
8. If equipped, ignition ON, verify that a test lamp illuminates between the communication enable circuit terminal OR the accessory wakeup
circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the circuit for an open/high resistance. If the circuits test normal, replace the BCM.
9. Ignition OFF for 60 seconds, test for less than 5 ohm between the serial data circuit terminals and the appropriate DLC terminal listed below:
* Class 2 serial data circuit terminal 2
* Low speed GMLAN serial data terminal 1
* High speed GMLAN serial data terminal 6 or 14
瀚慖f greater than the specified range, test the serial data circuit for an open/high resistance between the non communicating control module
and a control module setting the DTC or a serial data splice pack.
10. If all circuits test normal, replace the control module that is not communicating.
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 3072
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 3072
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
Note: Use the schematic to identify the following:
* Control modules the vehicle is equipped with
* Control module locations on the low and high speed GMLAN serial data circuits
* The control modules B+, ignition, ground, communication enable and serial data circuit terminals
1. Determine the control module that is not communicating. Refer to Control Module U Code List (See: Diagnostic Trouble Code
Descriptions/Control Module U Code List).
2. Using the Hybrid High Voltage Module Chart below, verify that the non-communicating control module is not a high voltage module. If the
control module is a high voltage module, perform the High Voltage Disabling (See: Hybrid Drive Systems/Battery System, Hybrid
Drive/Testing and Inspection/Initial Inspection and Diagnostic Overview/High Voltage Disabling) procedure before proceeding with this
diagnostic.
3. If high voltage disabling is required, reconnect the 12 V battery after performing the high voltage disabling procedure.
4. Ignition OFF, disconnect the harness connector of the control module that is not communicating.
5. Test for less than 10 ohm between each ground circuit terminal and ground.
瀚慖f greater than the specified range, test the ground circuit for an open/high resistance.
6. If equipped, verify that a test lamp illuminates between each B+ circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test the
control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
7. If equipped, ignition ON, verify that a test lamp illuminates between each ignition circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test
the control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
Note: Only the high speed GMLAN modules have a serial data communication enable circuit OR an accessory wakeup serial data circuit,
and the BCM is the output for these circuits. Refer to the module schematics to identify which modules have these circuits.
8. If equipped, ignition ON, verify that a test lamp illuminates between the communication enable circuit terminal OR the accessory wakeup
circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the circuit for an open/high resistance. If the circuits test normal, replace the BCM.
9. Ignition OFF for 60 seconds, test for less than 5 ohm between the serial data circuit terminals and the appropriate DLC terminal listed below:
* Class 2 serial data circuit terminal 2
* Low speed GMLAN serial data terminal 1
* High speed GMLAN serial data terminal 6 or 14
瀚慖f greater than the specified range, test the serial data circuit for an open/high resistance between the non communicating control module
and a control module setting the DTC or a serial data splice pack.
10. If all circuits test normal, replace the control module that is not communicating.
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
Note: Use the schematic to identify the following:
* Control modules the vehicle is equipped with
* Control module locations on the low and high speed GMLAN serial data circuits
* The control modules B+, ignition, ground, communication enable and serial data circuit terminals
1. Determine the control module that is not communicating. Refer to Control Module U Code List (See: Diagnostic Trouble Code
Descriptions/Control Module U Code List).
2. Using the Hybrid High Voltage Module Chart below, verify that the non-communicating control module is not a high voltage module. If the
control module is a high voltage module, perform the High Voltage Disabling (See: Hybrid Drive Systems/Battery System, Hybrid
Drive/Testing and Inspection/Initial Inspection and Diagnostic Overview/High Voltage Disabling) procedure before proceeding with this
diagnostic.
3. If high voltage disabling is required, reconnect the 12 V battery after performing the high voltage disabling procedure.
4. Ignition OFF, disconnect the harness connector of the control module that is not communicating.
5. Test for less than 10 ohm between each ground circuit terminal and ground.
瀚慖f greater than the specified range, test the ground circuit for an open/high resistance.
6. If equipped, verify that a test lamp illuminates between each B+ circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test the
control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
7. If equipped, ignition ON, verify that a test lamp illuminates between each ignition circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test
the control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
Note: Only the high speed GMLAN modules have a serial data communication enable circuit OR an accessory wakeup serial data circuit,
and the BCM is the output for these circuits. Refer to the module schematics to identify which modules have these circuits.
8. If equipped, ignition ON, verify that a test lamp illuminates between the communication enable circuit terminal OR the accessory wakeup
circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the circuit for an open/high resistance. If the circuits test normal, replace the BCM.
9. Ignition OFF for 60 seconds, test for less than 5 ohm between the serial data circuit terminals and the appropriate DLC terminal listed below:
* Class 2 serial data circuit terminal 2
* Low speed GMLAN serial data terminal 1
* High speed GMLAN serial data terminal 6 or 14
瀚慖f greater than the specified range, test the serial data circuit for an open/high resistance between the non communicating control module
and a control module setting the DTC or a serial data splice pack.
10. If all circuits test normal, replace the control module that is not communicating.
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 3065
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 3065
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
Note: Use the schematic to identify the following:
* Control modules the vehicle is equipped with
* Control module locations on the low and high speed GMLAN serial data circuits
* The control modules B+, ignition, ground, communication enable and serial data circuit terminals
1. Determine the control module that is not communicating. Refer to Control Module U Code List (See: Diagnostic Trouble Code
Descriptions/Control Module U Code List).
2. Using the Hybrid High Voltage Module Chart below, verify that the non-communicating control module is not a high voltage module. If the
control module is a high voltage module, perform the High Voltage Disabling (See: Hybrid Drive Systems/Battery System, Hybrid
Drive/Testing and Inspection/Initial Inspection and Diagnostic Overview/High Voltage Disabling) procedure before proceeding with this
diagnostic.
3. If high voltage disabling is required, reconnect the 12 V battery after performing the high voltage disabling procedure.
4. Ignition OFF, disconnect the harness connector of the control module that is not communicating.
5. Test for less than 10 ohm between each ground circuit terminal and ground.
瀚慖f greater than the specified range, test the ground circuit for an open/high resistance.
6. If equipped, verify that a test lamp illuminates between each B+ circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test the
control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
7. If equipped, ignition ON, verify that a test lamp illuminates between each ignition circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test
the control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
Note: Only the high speed GMLAN modules have a serial data communication enable circuit OR an accessory wakeup serial data circuit,
and the BCM is the output for these circuits. Refer to the module schematics to identify which modules have these circuits.
8. If equipped, ignition ON, verify that a test lamp illuminates between the communication enable circuit terminal OR the accessory wakeup
circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the circuit for an open/high resistance. If the circuits test normal, replace the BCM.
9. Ignition OFF for 60 seconds, test for less than 5 ohm between the serial data circuit terminals and the appropriate DLC terminal listed below:
* Class 2 serial data circuit terminal 2
* Low speed GMLAN serial data terminal 1
* High speed GMLAN serial data terminal 6 or 14
瀚慖f greater than the specified range, test the serial data circuit for an open/high resistance between the non communicating control module
and a control module setting the DTC or a serial data splice pack.
10. If all circuits test normal, replace the control module that is not communicating.
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
Note: Use the schematic to identify the following:
* Control modules the vehicle is equipped with
* Control module locations on the low and high speed GMLAN serial data circuits
* The control modules B+, ignition, ground, communication enable and serial data circuit terminals
1. Determine the control module that is not communicating. Refer to Control Module U Code List (See: Diagnostic Trouble Code
Descriptions/Control Module U Code List).
2. Using the Hybrid High Voltage Module Chart below, verify that the non-communicating control module is not a high voltage module. If the
control module is a high voltage module, perform the High Voltage Disabling (See: Hybrid Drive Systems/Battery System, Hybrid
Drive/Testing and Inspection/Initial Inspection and Diagnostic Overview/High Voltage Disabling) procedure before proceeding with this
diagnostic.
3. If high voltage disabling is required, reconnect the 12 V battery after performing the high voltage disabling procedure.
4. Ignition OFF, disconnect the harness connector of the control module that is not communicating.
5. Test for less than 10 ohm between each ground circuit terminal and ground.
瀚慖f greater than the specified range, test the ground circuit for an open/high resistance.
6. If equipped, verify that a test lamp illuminates between each B+ circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test the
control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
7. If equipped, ignition ON, verify that a test lamp illuminates between each ignition circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test
the control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
Note: Only the high speed GMLAN modules have a serial data communication enable circuit OR an accessory wakeup serial data circuit,
and the BCM is the output for these circuits. Refer to the module schematics to identify which modules have these circuits.
8. If equipped, ignition ON, verify that a test lamp illuminates between the communication enable circuit terminal OR the accessory wakeup
circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the circuit for an open/high resistance. If the circuits test normal, replace the BCM.
9. Ignition OFF for 60 seconds, test for less than 5 ohm between the serial data circuit terminals and the appropriate DLC terminal listed below:
* Class 2 serial data circuit terminal 2
* Low speed GMLAN serial data terminal 1
* High speed GMLAN serial data terminal 6 or 14
瀚慖f greater than the specified range, test the serial data circuit for an open/high resistance between the non communicating control module
and a control module setting the DTC or a serial data splice pack.
10. If all circuits test normal, replace the control module that is not communicating.
Saturday, March 14, 2020
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 3058
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 3058
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
Note: Use the schematic to identify the following:
* Control modules the vehicle is equipped with
* Control module locations on the low and high speed GMLAN serial data circuits
* The control modules B+, ignition, ground, communication enable and serial data circuit terminals
1. Determine the control module that is not communicating. Refer to Control Module U Code List (See: Diagnostic Trouble Code
Descriptions/Control Module U Code List).
2. Using the Hybrid High Voltage Module Chart below, verify that the non-communicating control module is not a high voltage module. If the
control module is a high voltage module, perform the High Voltage Disabling (See: Hybrid Drive Systems/Battery System, Hybrid
Drive/Testing and Inspection/Initial Inspection and Diagnostic Overview/High Voltage Disabling) procedure before proceeding with this
diagnostic.
3. If high voltage disabling is required, reconnect the 12 V battery after performing the high voltage disabling procedure.
4. Ignition OFF, disconnect the harness connector of the control module that is not communicating.
5. Test for less than 10 ohm between each ground circuit terminal and ground.
瀚慖f greater than the specified range, test the ground circuit for an open/high resistance.
6. If equipped, verify that a test lamp illuminates between each B+ circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test the
control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
7. If equipped, ignition ON, verify that a test lamp illuminates between each ignition circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test
the control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
Note: Only the high speed GMLAN modules have a serial data communication enable circuit OR an accessory wakeup serial data circuit,
and the BCM is the output for these circuits. Refer to the module schematics to identify which modules have these circuits.
8. If equipped, ignition ON, verify that a test lamp illuminates between the communication enable circuit terminal OR the accessory wakeup
circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the circuit for an open/high resistance. If the circuits test normal, replace the BCM.
9. Ignition OFF for 60 seconds, test for less than 5 ohm between the serial data circuit terminals and the appropriate DLC terminal listed below:
* Class 2 serial data circuit terminal 2
* Low speed GMLAN serial data terminal 1
* High speed GMLAN serial data terminal 6 or 14
瀚慖f greater than the specified range, test the serial data circuit for an open/high resistance between the non communicating control module
and a control module setting the DTC or a serial data splice pack.
10. If all circuits test normal, replace the control module that is not communicating.
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
Note: Use the schematic to identify the following:
* Control modules the vehicle is equipped with
* Control module locations on the low and high speed GMLAN serial data circuits
* The control modules B+, ignition, ground, communication enable and serial data circuit terminals
1. Determine the control module that is not communicating. Refer to Control Module U Code List (See: Diagnostic Trouble Code
Descriptions/Control Module U Code List).
2. Using the Hybrid High Voltage Module Chart below, verify that the non-communicating control module is not a high voltage module. If the
control module is a high voltage module, perform the High Voltage Disabling (See: Hybrid Drive Systems/Battery System, Hybrid
Drive/Testing and Inspection/Initial Inspection and Diagnostic Overview/High Voltage Disabling) procedure before proceeding with this
diagnostic.
3. If high voltage disabling is required, reconnect the 12 V battery after performing the high voltage disabling procedure.
4. Ignition OFF, disconnect the harness connector of the control module that is not communicating.
5. Test for less than 10 ohm between each ground circuit terminal and ground.
瀚慖f greater than the specified range, test the ground circuit for an open/high resistance.
6. If equipped, verify that a test lamp illuminates between each B+ circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test the
control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
7. If equipped, ignition ON, verify that a test lamp illuminates between each ignition circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test
the control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
Note: Only the high speed GMLAN modules have a serial data communication enable circuit OR an accessory wakeup serial data circuit,
and the BCM is the output for these circuits. Refer to the module schematics to identify which modules have these circuits.
8. If equipped, ignition ON, verify that a test lamp illuminates between the communication enable circuit terminal OR the accessory wakeup
circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the circuit for an open/high resistance. If the circuits test normal, replace the BCM.
9. Ignition OFF for 60 seconds, test for less than 5 ohm between the serial data circuit terminals and the appropriate DLC terminal listed below:
* Class 2 serial data circuit terminal 2
* Low speed GMLAN serial data terminal 1
* High speed GMLAN serial data terminal 6 or 14
瀚慖f greater than the specified range, test the serial data circuit for an open/high resistance between the non communicating control module
and a control module setting the DTC or a serial data splice pack.
10. If all circuits test normal, replace the control module that is not communicating.
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 3051
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 3051
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
Note: Use the schematic to identify the following:
* Control modules the vehicle is equipped with
* Control module locations on the low and high speed GMLAN serial data circuits
* The control modules B+, ignition, ground, communication enable and serial data circuit terminals
1. Determine the control module that is not communicating. Refer to Control Module U Code List (See: Diagnostic Trouble Code
Descriptions/Control Module U Code List).
2. Using the Hybrid High Voltage Module Chart below, verify that the non-communicating control module is not a high voltage module. If the
control module is a high voltage module, perform the High Voltage Disabling (See: Hybrid Drive Systems/Battery System, Hybrid
Drive/Testing and Inspection/Initial Inspection and Diagnostic Overview/High Voltage Disabling) procedure before proceeding with this
diagnostic.
3. If high voltage disabling is required, reconnect the 12 V battery after performing the high voltage disabling procedure.
4. Ignition OFF, disconnect the harness connector of the control module that is not communicating.
5. Test for less than 10 ohm between each ground circuit terminal and ground.
瀚慖f greater than the specified range, test the ground circuit for an open/high resistance.
6. If equipped, verify that a test lamp illuminates between each B+ circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test the
control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
7. If equipped, ignition ON, verify that a test lamp illuminates between each ignition circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test
the control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
Note: Only the high speed GMLAN modules have a serial data communication enable circuit OR an accessory wakeup serial data circuit,
and the BCM is the output for these circuits. Refer to the module schematics to identify which modules have these circuits.
8. If equipped, ignition ON, verify that a test lamp illuminates between the communication enable circuit terminal OR the accessory wakeup
circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the circuit for an open/high resistance. If the circuits test normal, replace the BCM.
9. Ignition OFF for 60 seconds, test for less than 5 ohm between the serial data circuit terminals and the appropriate DLC terminal listed below:
* Class 2 serial data circuit terminal 2
* Low speed GMLAN serial data terminal 1
* High speed GMLAN serial data terminal 6 or 14
瀚慖f greater than the specified range, test the serial data circuit for an open/high resistance between the non communicating control module
and a control module setting the DTC or a serial data splice pack.
10. If all circuits test normal, replace the control module that is not communicating.
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
Note: Use the schematic to identify the following:
* Control modules the vehicle is equipped with
* Control module locations on the low and high speed GMLAN serial data circuits
* The control modules B+, ignition, ground, communication enable and serial data circuit terminals
1. Determine the control module that is not communicating. Refer to Control Module U Code List (See: Diagnostic Trouble Code
Descriptions/Control Module U Code List).
2. Using the Hybrid High Voltage Module Chart below, verify that the non-communicating control module is not a high voltage module. If the
control module is a high voltage module, perform the High Voltage Disabling (See: Hybrid Drive Systems/Battery System, Hybrid
Drive/Testing and Inspection/Initial Inspection and Diagnostic Overview/High Voltage Disabling) procedure before proceeding with this
diagnostic.
3. If high voltage disabling is required, reconnect the 12 V battery after performing the high voltage disabling procedure.
4. Ignition OFF, disconnect the harness connector of the control module that is not communicating.
5. Test for less than 10 ohm between each ground circuit terminal and ground.
瀚慖f greater than the specified range, test the ground circuit for an open/high resistance.
6. If equipped, verify that a test lamp illuminates between each B+ circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test the
control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
7. If equipped, ignition ON, verify that a test lamp illuminates between each ignition circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test
the control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
Note: Only the high speed GMLAN modules have a serial data communication enable circuit OR an accessory wakeup serial data circuit,
and the BCM is the output for these circuits. Refer to the module schematics to identify which modules have these circuits.
8. If equipped, ignition ON, verify that a test lamp illuminates between the communication enable circuit terminal OR the accessory wakeup
circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the circuit for an open/high resistance. If the circuits test normal, replace the BCM.
9. Ignition OFF for 60 seconds, test for less than 5 ohm between the serial data circuit terminals and the appropriate DLC terminal listed below:
* Class 2 serial data circuit terminal 2
* Low speed GMLAN serial data terminal 1
* High speed GMLAN serial data terminal 6 or 14
瀚慖f greater than the specified range, test the serial data circuit for an open/high resistance between the non communicating control module
and a control module setting the DTC or a serial data splice pack.
10. If all circuits test normal, replace the control module that is not communicating.
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 3044
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 3044
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
Note: Use the schematic to identify the following:
* Control modules the vehicle is equipped with
* Control module locations on the low and high speed GMLAN serial data circuits
* The control modules B+, ignition, ground, communication enable and serial data circuit terminals
1. Determine the control module that is not communicating. Refer to Control Module U Code List (See: Diagnostic Trouble Code
Descriptions/Control Module U Code List).
2. Using the Hybrid High Voltage Module Chart below, verify that the non-communicating control module is not a high voltage module. If the
control module is a high voltage module, perform the High Voltage Disabling (See: Hybrid Drive Systems/Battery System, Hybrid
Drive/Testing and Inspection/Initial Inspection and Diagnostic Overview/High Voltage Disabling) procedure before proceeding with this
diagnostic.
3. If high voltage disabling is required, reconnect the 12 V battery after performing the high voltage disabling procedure.
4. Ignition OFF, disconnect the harness connector of the control module that is not communicating.
5. Test for less than 10 ohm between each ground circuit terminal and ground.
瀚慖f greater than the specified range, test the ground circuit for an open/high resistance.
6. If equipped, verify that a test lamp illuminates between each B+ circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test the
control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
7. If equipped, ignition ON, verify that a test lamp illuminates between each ignition circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test
the control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
Note: Only the high speed GMLAN modules have a serial data communication enable circuit OR an accessory wakeup serial data circuit,
and the BCM is the output for these circuits. Refer to the module schematics to identify which modules have these circuits.
8. If equipped, ignition ON, verify that a test lamp illuminates between the communication enable circuit terminal OR the accessory wakeup
circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the circuit for an open/high resistance. If the circuits test normal, replace the BCM.
9. Ignition OFF for 60 seconds, test for less than 5 ohm between the serial data circuit terminals and the appropriate DLC terminal listed below:
* Class 2 serial data circuit terminal 2
* Low speed GMLAN serial data terminal 1
* High speed GMLAN serial data terminal 6 or 14
瀚慖f greater than the specified range, test the serial data circuit for an open/high resistance between the non communicating control module
and a control module setting the DTC or a serial data splice pack.
10. If all circuits test normal, replace the control module that is not communicating.
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
Note: Use the schematic to identify the following:
* Control modules the vehicle is equipped with
* Control module locations on the low and high speed GMLAN serial data circuits
* The control modules B+, ignition, ground, communication enable and serial data circuit terminals
1. Determine the control module that is not communicating. Refer to Control Module U Code List (See: Diagnostic Trouble Code
Descriptions/Control Module U Code List).
2. Using the Hybrid High Voltage Module Chart below, verify that the non-communicating control module is not a high voltage module. If the
control module is a high voltage module, perform the High Voltage Disabling (See: Hybrid Drive Systems/Battery System, Hybrid
Drive/Testing and Inspection/Initial Inspection and Diagnostic Overview/High Voltage Disabling) procedure before proceeding with this
diagnostic.
3. If high voltage disabling is required, reconnect the 12 V battery after performing the high voltage disabling procedure.
4. Ignition OFF, disconnect the harness connector of the control module that is not communicating.
5. Test for less than 10 ohm between each ground circuit terminal and ground.
瀚慖f greater than the specified range, test the ground circuit for an open/high resistance.
6. If equipped, verify that a test lamp illuminates between each B+ circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test the
control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
7. If equipped, ignition ON, verify that a test lamp illuminates between each ignition circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test
the control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
Note: Only the high speed GMLAN modules have a serial data communication enable circuit OR an accessory wakeup serial data circuit,
and the BCM is the output for these circuits. Refer to the module schematics to identify which modules have these circuits.
8. If equipped, ignition ON, verify that a test lamp illuminates between the communication enable circuit terminal OR the accessory wakeup
circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the circuit for an open/high resistance. If the circuits test normal, replace the BCM.
9. Ignition OFF for 60 seconds, test for less than 5 ohm between the serial data circuit terminals and the appropriate DLC terminal listed below:
* Class 2 serial data circuit terminal 2
* Low speed GMLAN serial data terminal 1
* High speed GMLAN serial data terminal 6 or 14
瀚慖f greater than the specified range, test the serial data circuit for an open/high resistance between the non communicating control module
and a control module setting the DTC or a serial data splice pack.
10. If all circuits test normal, replace the control module that is not communicating.
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 3037
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 3037
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
Note: Use the schematic to identify the following:
* Control modules the vehicle is equipped with
* Control module locations on the low and high speed GMLAN serial data circuits
* The control modules B+, ignition, ground, communication enable and serial data circuit terminals
1. Determine the control module that is not communicating. Refer to Control Module U Code List (See: Diagnostic Trouble Code
Descriptions/Control Module U Code List).
2. Using the Hybrid High Voltage Module Chart below, verify that the non-communicating control module is not a high voltage module. If the
control module is a high voltage module, perform the High Voltage Disabling (See: Hybrid Drive Systems/Battery System, Hybrid
Drive/Testing and Inspection/Initial Inspection and Diagnostic Overview/High Voltage Disabling) procedure before proceeding with this
diagnostic.
3. If high voltage disabling is required, reconnect the 12 V battery after performing the high voltage disabling procedure.
4. Ignition OFF, disconnect the harness connector of the control module that is not communicating.
5. Test for less than 10 ohm between each ground circuit terminal and ground.
瀚慖f greater than the specified range, test the ground circuit for an open/high resistance.
6. If equipped, verify that a test lamp illuminates between each B+ circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test the
control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
7. If equipped, ignition ON, verify that a test lamp illuminates between each ignition circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test
the control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
Note: Only the high speed GMLAN modules have a serial data communication enable circuit OR an accessory wakeup serial data circuit,
and the BCM is the output for these circuits. Refer to the module schematics to identify which modules have these circuits.
8. If equipped, ignition ON, verify that a test lamp illuminates between the communication enable circuit terminal OR the accessory wakeup
circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the circuit for an open/high resistance. If the circuits test normal, replace the BCM.
9. Ignition OFF for 60 seconds, test for less than 5 ohm between the serial data circuit terminals and the appropriate DLC terminal listed below:
* Class 2 serial data circuit terminal 2
* Low speed GMLAN serial data terminal 1
* High speed GMLAN serial data terminal 6 or 14
瀚慖f greater than the specified range, test the serial data circuit for an open/high resistance between the non communicating control module
and a control module setting the DTC or a serial data splice pack.
10. If all circuits test normal, replace the control module that is not communicating.
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
Note: Use the schematic to identify the following:
* Control modules the vehicle is equipped with
* Control module locations on the low and high speed GMLAN serial data circuits
* The control modules B+, ignition, ground, communication enable and serial data circuit terminals
1. Determine the control module that is not communicating. Refer to Control Module U Code List (See: Diagnostic Trouble Code
Descriptions/Control Module U Code List).
2. Using the Hybrid High Voltage Module Chart below, verify that the non-communicating control module is not a high voltage module. If the
control module is a high voltage module, perform the High Voltage Disabling (See: Hybrid Drive Systems/Battery System, Hybrid
Drive/Testing and Inspection/Initial Inspection and Diagnostic Overview/High Voltage Disabling) procedure before proceeding with this
diagnostic.
3. If high voltage disabling is required, reconnect the 12 V battery after performing the high voltage disabling procedure.
4. Ignition OFF, disconnect the harness connector of the control module that is not communicating.
5. Test for less than 10 ohm between each ground circuit terminal and ground.
瀚慖f greater than the specified range, test the ground circuit for an open/high resistance.
6. If equipped, verify that a test lamp illuminates between each B+ circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test the
control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
7. If equipped, ignition ON, verify that a test lamp illuminates between each ignition circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit fuse is open, test
the control circuits of the control module for a short to ground. If the circuits test normal, replace the control module.
Note: Only the high speed GMLAN modules have a serial data communication enable circuit OR an accessory wakeup serial data circuit,
and the BCM is the output for these circuits. Refer to the module schematics to identify which modules have these circuits.
8. If equipped, ignition ON, verify that a test lamp illuminates between the communication enable circuit terminal OR the accessory wakeup
circuit terminal and ground.
瀚慖f the test lamp does not illuminate, test the circuit for an open/high resistance. If the circuits test normal, replace the BCM.
9. Ignition OFF for 60 seconds, test for less than 5 ohm between the serial data circuit terminals and the appropriate DLC terminal listed below:
* Class 2 serial data circuit terminal 2
* Low speed GMLAN serial data terminal 1
* High speed GMLAN serial data terminal 6 or 14
瀚慖f greater than the specified range, test the serial data circuit for an open/high resistance between the non communicating control module
and a control module setting the DTC or a serial data splice pack.
10. If all circuits test normal, replace the control module that is not communicating.
Subscribe to:
Posts (Atom)