2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 517
1. Ignition OFF, disconnect the X2, X5 harness connectors at the MSM.
2. Test for 850 Ohms - 300 kOhms between the signal circuit terminal 2 X5 and the low reference circuit terminal 6 X2.
瀚慖f less than the specified range, test for a short between the signal and low reference circuits. If the circuits test normal, replace the seat
cushion heater element/temperature sensor.
瀚慖f greater than the specified range, test the signal and low reference circuits for a short to voltage or an open/high resistance. If the circuits
test normal, replace the seat cushion heater element/temperature sensor.
3. Connect the X2, X5 harness connectors at the MSM.
4. Disconnect the harness connector at the seat cushion heater element/temperature sensor.
5. Ignition ON, test for 4.8 - 5.2 V between the signal circuit terminal C and ground.
瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace
the MSM.
瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the MSM.
6. If all circuits test normal, replace the MSM.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Driver or Passenger Seat Cushion Heater Replacement (without HP2) ()Driver or Passenger Seat Cushion Heater Replacement (with HP2)
()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for the MSM replacement, setup, and programming
HP2 or Dealer Installed W/O Memory
DTC B1925 or B2170 (HP2 or Dealer Installed w/o Memory)
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC B1925 02
- Left Seat Heater Cushion Sensor Circuit Shorted to Ground
DTC B1925 05
- Left Seat Heater Cushion Sensor Circuit Shorted to Battery or Open
DTC B2170 02
- Right Seat Heater Cushion Sensor Circuit Shorted to Ground
DTC B2170 05
- Right Seat Heater Cushion Sensor Circuit Shorted to Battery or Open
Diagnostic Fault Information
Showing posts with label X5 harness connectors at the MSM.. Show all posts
Showing posts with label X5 harness connectors at the MSM.. Show all posts
Monday, September 7, 2020
Thursday, November 14, 2019
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 558
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 558
1. Ignition OFF, disconnect the X2, X5 harness connectors at the MSM.
2. Test for 850 Ohms - 300 kOhms between the signal circuit terminal 2 X5 and the low reference circuit terminal 6 X2.
瀚慖f less than the specified range, test for a short between the signal and low reference circuits. If the circuits test normal, replace the seat
cushion heater element/temperature sensor.
瀚慖f greater than the specified range, test the signal and low reference circuits for a short to voltage or an open/high resistance. If the circuits
test normal, replace the seat cushion heater element/temperature sensor.
3. Connect the X2, X5 harness connectors at the MSM.
4. Disconnect the harness connector at the seat cushion heater element/temperature sensor.
5. Ignition ON, test for 4.8 - 5.2 V between the signal circuit terminal C and ground.
瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace
the MSM.
瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the MSM.
6. If all circuits test normal, replace the MSM.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Driver or Passenger Seat Cushion Heater Replacement (without HP2) ()Driver or Passenger Seat Cushion Heater Replacement (with HP2)
()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for the MSM replacement, setup, and programming
Dealer Installed
DTC B1935 or B2180 (Dealer Installed)
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC B1935 04
- Left Seat Back Heater Circuit Open
DTC B1935 0A
- Left Seat Back Heater Circuit Rate of Change Below Threshold
DTC B1935 0B
- Left Seat Back Heater Circuit Current Above Threshold
DTC B1935 0C
- Left Seat Back Heater Circuit Current Below Threshold
DTC B1935 0D
- Left Seat Back Heater Circuit Resistance Above Threshold
DTC B1935 0E
- Left Seat Back Heater Circuit Resistance Below Threshold
DTC B1935 1F
- Left Seat Back Heater Circuit Intermittent
DTC B2180 04
- Right Seat Back Heater Circuit Open
DTC B2180 0A
- Right Seat Back Heater Circuit Rate of Change Below Threshold
DTC B2180 0B
- Right Seat Back Heater Circuit Current Above Threshold
1. Ignition OFF, disconnect the X2, X5 harness connectors at the MSM.
2. Test for 850 Ohms - 300 kOhms between the signal circuit terminal 2 X5 and the low reference circuit terminal 6 X2.
瀚慖f less than the specified range, test for a short between the signal and low reference circuits. If the circuits test normal, replace the seat
cushion heater element/temperature sensor.
瀚慖f greater than the specified range, test the signal and low reference circuits for a short to voltage or an open/high resistance. If the circuits
test normal, replace the seat cushion heater element/temperature sensor.
3. Connect the X2, X5 harness connectors at the MSM.
4. Disconnect the harness connector at the seat cushion heater element/temperature sensor.
5. Ignition ON, test for 4.8 - 5.2 V between the signal circuit terminal C and ground.
瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace
the MSM.
瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the MSM.
6. If all circuits test normal, replace the MSM.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Driver or Passenger Seat Cushion Heater Replacement (without HP2) ()Driver or Passenger Seat Cushion Heater Replacement (with HP2)
()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for the MSM replacement, setup, and programming
Dealer Installed
DTC B1935 or B2180 (Dealer Installed)
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC B1935 04
- Left Seat Back Heater Circuit Open
DTC B1935 0A
- Left Seat Back Heater Circuit Rate of Change Below Threshold
DTC B1935 0B
- Left Seat Back Heater Circuit Current Above Threshold
DTC B1935 0C
- Left Seat Back Heater Circuit Current Below Threshold
DTC B1935 0D
- Left Seat Back Heater Circuit Resistance Above Threshold
DTC B1935 0E
- Left Seat Back Heater Circuit Resistance Below Threshold
DTC B1935 1F
- Left Seat Back Heater Circuit Intermittent
DTC B2180 04
- Right Seat Back Heater Circuit Open
DTC B2180 0A
- Right Seat Back Heater Circuit Rate of Change Below Threshold
DTC B2180 0B
- Right Seat Back Heater Circuit Current Above Threshold
Wednesday, November 13, 2019
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 544
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 544
1. Ignition OFF, disconnect the X2, X5 harness connectors at the MSM.
2. Test for 850 Ohms - 300 kOhms between the signal circuit terminal 2 X5 and the low reference circuit terminal 6 X2.
瀚慖f less than the specified range, test for a short between the signal and low reference circuits. If the circuits test normal, replace the seat
cushion heater element/temperature sensor.
瀚慖f greater than the specified range, test the signal and low reference circuits for a short to voltage or an open/high resistance. If the circuits
test normal, replace the seat cushion heater element/temperature sensor.
3. Connect the X2, X5 harness connectors at the MSM.
4. Disconnect the harness connector at the seat cushion heater element/temperature sensor.
5. Ignition ON, test for 4.8 - 5.2 V between the signal circuit terminal C and ground.
瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace
the MSM.
瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the MSM.
6. If all circuits test normal, replace the MSM.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Driver or Passenger Seat Cushion Heater Replacement (without HP2) ()Driver or Passenger Seat Cushion Heater Replacement (with HP2)
()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for the MSM replacement, setup, and programming
HP2 or Dealer Installed W/O Memory
DTC B1925 or B2170 (HP2 or Dealer Installed w/o Memory)
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC B1925 02
- Left Seat Heater Cushion Sensor Circuit Shorted to Ground
DTC B1925 05
- Left Seat Heater Cushion Sensor Circuit Shorted to Battery or Open
DTC B2170 02
- Right Seat Heater Cushion Sensor Circuit Shorted to Ground
DTC B2170 05
- Right Seat Heater Cushion Sensor Circuit Shorted to Battery or Open
Diagnostic Fault Information
1. Ignition OFF, disconnect the X2, X5 harness connectors at the MSM.
2. Test for 850 Ohms - 300 kOhms between the signal circuit terminal 2 X5 and the low reference circuit terminal 6 X2.
瀚慖f less than the specified range, test for a short between the signal and low reference circuits. If the circuits test normal, replace the seat
cushion heater element/temperature sensor.
瀚慖f greater than the specified range, test the signal and low reference circuits for a short to voltage or an open/high resistance. If the circuits
test normal, replace the seat cushion heater element/temperature sensor.
3. Connect the X2, X5 harness connectors at the MSM.
4. Disconnect the harness connector at the seat cushion heater element/temperature sensor.
5. Ignition ON, test for 4.8 - 5.2 V between the signal circuit terminal C and ground.
瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace
the MSM.
瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the MSM.
6. If all circuits test normal, replace the MSM.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Driver or Passenger Seat Cushion Heater Replacement (without HP2) ()Driver or Passenger Seat Cushion Heater Replacement (with HP2)
()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for the MSM replacement, setup, and programming
HP2 or Dealer Installed W/O Memory
DTC B1925 or B2170 (HP2 or Dealer Installed w/o Memory)
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC B1925 02
- Left Seat Heater Cushion Sensor Circuit Shorted to Ground
DTC B1925 05
- Left Seat Heater Cushion Sensor Circuit Shorted to Battery or Open
DTC B2170 02
- Right Seat Heater Cushion Sensor Circuit Shorted to Ground
DTC B2170 05
- Right Seat Heater Cushion Sensor Circuit Shorted to Battery or Open
Diagnostic Fault Information
Subscribe to:
Posts (Atom)