2010 Cadillac Truck SRX AWD V6-3.0L Page 560

2010 Cadillac Truck SRX AWD V6-3.0L Page 560

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic repair.

* Liftgate Release Switch Replacement (See: Body and Frame/Doors, Hood and Trunk/Trunk / Liftgate/Trunk / Liftgate Switch/Service and

Repair/Liftgate Release Switch Replacement)

* Control Module References (See: Testing and Inspection/Programming and Relearning)for BCM replacement, setup and programming

Liftgate Handle Switch Malfunction

Liftgate Handle Switch Malfunction - DTC B2494

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptor

DTC B2494 02

- Liftgate Handle Switch Circuit Short to Ground

Diagnostic Fault Information

Circuit/System Description

The power liftgate handle switch circuit provides a single input to the liftgate control module. The liftgate handle switch is supplied a signal

voltage, when the switch contact closes and the voltage drops, the liftgate control module detects the voltage drop and commands the liftgate to

release.

Conditions for Running the DTC

The system voltage is 9-16 V.

Conditions for Setting the DTC

The liftgate handle switch signal circuit is active for greater than 30 seconds.

Action Taken When the DTC Sets

The liftgate control module will ignore the signal from the liftgate handle switch. Normal power liftgate operation will be available from the interior

liftgate control switch or from a request from the remote keyless entry module.

Conditions for Clearing the DTC

* The DTC will be current for as long as the fault is present.

* When the fault is no longer present, the DTC will be a history DTC.

* A history DTC will clear after 50 ignition cycles.

Diagnostic Aids

* If the liftgate will not release from the closed position, refer to Opening the Liftgate Without Electrical Power (See: Body and Frame/Doors,

Hood and Trunk/Trunk / Liftgate/Service and Repair/Procedures) for the appropriate procedure

* Whenever the liftgate control module loses power or is disconnected, the ignition must be cycled OFF then ON in order to reactivate the

liftgate control module.

Reference Information

Schematic Reference

Liftgate Schematics (See: Body and Frame/Locks/Diagrams/Electrical Diagrams/Liftgate Schematics)

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 231

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 231

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic repair.

* Liftgate Latch Replacement (See: Body and Frame/Doors, Hood and Trunk/Trunk / Liftgate/Trunk / Liftgate Latch/Service and Repair)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for the liftgate control module replacement, setup

and programming

B153E

Liftgate Angle Sensor Malfunction - DTC B153E

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptor

DTC B153E 08

- Power Liftgate Angle Sensor - External Signal Invalid

Diagnostic Fault Information

Circuit/System Description

The liftgate control module continuously monitors power liftgate operation and calculates its location and direction of travel using 2 inputs from the

liftgate position sensor. One input returns the position of the liftgate relative to the latch along the x-axis and the other returns the position of the

liftgate relative to the latch along the y-axis. The liftgate control module then uses these 2 inputs together to calculate its angle relative to the

liftgate latch.

Conditions for Running the DTC

The system voltage is 9-16 V.

Conditions for Setting the DTC

The liftgate control module does not detect the angle inputs when the liftgate is in motion.

Action Taken When the DTC Sets

The liftgate will only be operational in the manual mode.

Conditions for Clearing the DTC

* The DTC will be current for as long as the fault is present.

* When the fault is no longer present, the DTC will be a history DTC.

* A history DTC will clear after 50 ignition cycles.

Diagnostic Aids

Note: Before testing can be performed, the liftgate must be opened. Refer to Opening the Liftgate Without Electrical Power (See: Body and

Frame/Doors, Hood and Trunk/Trunk / Liftgate/Service and Repair/Procedures) for the appropriate procedure.

Whenever the liftgate module loses power or is disconnected, the ignition must be cycled OFF then ON in order to reactivate the liftgate module.

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 560

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 560

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic repair.

* Liftgate Release Switch Replacement (See: Body and Frame/Doors, Hood and Trunk/Trunk / Liftgate/Trunk / Liftgate Switch/Service and

Repair/Liftgate Release Switch Replacement)

* Control Module References (See: Testing and Inspection/Programming and Relearning)for BCM replacement, setup and programming

Liftgate Handle Switch Malfunction

Liftgate Handle Switch Malfunction - DTC B2494

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptor

DTC B2494 02

- Liftgate Handle Switch Circuit Short to Ground

Diagnostic Fault Information

Circuit/System Description

The power liftgate handle switch circuit provides a single input to the liftgate control module. The liftgate handle switch is supplied a signal

voltage, when the switch contact closes and the voltage drops, the liftgate control module detects the voltage drop and commands the liftgate to

release.

Conditions for Running the DTC

The system voltage is 9-16 V.

Conditions for Setting the DTC

The liftgate handle switch signal circuit is active for greater than 30 seconds.

Action Taken When the DTC Sets

The liftgate control module will ignore the signal from the liftgate handle switch. Normal power liftgate operation will be available from the interior

liftgate control switch or from a request from the remote keyless entry module.

Conditions for Clearing the DTC

* The DTC will be current for as long as the fault is present.

* When the fault is no longer present, the DTC will be a history DTC.

* A history DTC will clear after 50 ignition cycles.

Diagnostic Aids

* If the liftgate will not release from the closed position, refer to Opening the Liftgate Without Electrical Power (See: Body and Frame/Doors,

Hood and Trunk/Trunk / Liftgate/Service and Repair/Procedures) for the appropriate procedure

* Whenever the liftgate control module loses power or is disconnected, the ignition must be cycled OFF then ON in order to reactivate the

liftgate control module.

Reference Information

Schematic Reference

Liftgate Schematics (See: Body and Frame/Locks/Diagrams/Electrical Diagrams/Liftgate Schematics)