2010 Cadillac Truck Escalade RWD V8-6.2L Page 1192
P0AEF, P0AF4, P0BD3, P0BD8, P0BDD, and P0BE2
Ignition ON.
P0AF0, P0AF5, P0BD4, P0BD9, P0BDE, and P0BE3
* Ignition ON.
* Motor temperature is greater than -40掳C (-40掳F).
瀚慖f motor temperature is less than -40掳C (-40掳F) at Ignition ON, the drive motor must operate at greater than 20 Nm (14.75 lb ft) for a
cumulative time of 1.5 minutes before the DTC will run.
Conditions for Setting the DTC
P0AEE, P0AF3, P0BD2, P0BD7, P0BDC, and P0BE1
* A 15掳C ( 27掳F) difference is observed between the individual inverter phase temperature sensor and the average of all the inverter phase
temperatures.
* The above condition is present for 4 seconds.
P0AEF, P0AF4, P0BD3, P0BD8, P0BDD, and P0BE2
The inverter phase temperature sensor is greater than 125掳C (275掳F) for 3 seconds.
P0AF0, P0AF5, P0BD4, P0BD9, P0BDE, and P0BE3
The inverter phase temperature sensor is less than -40掳C (-40掳F) for 3 seconds.
Action Taken When the DTC Sets
* DTCs P0AEE, P0AEF, P0AF0, P0AF3, P0AF4, P0AF5, P0BD2, P0BD3, P0BD4, P0BD7, P0BD8, P0BD9, P0BDC, P0BDD, P0BDE,
P0BE1, P0BE2 AND P0BE3 are Type B DTCs.
* The PIM commands the battery energy control module (BECM) to open the high voltage contactor relays.
Conditions for Clearing the DTC
DTCs P0AEE, P0AEF, P0AF0, P0AF3, P0AF4, P0AF5, P0BD2, P0BD3, P0BD4, P0BD7, P0BD8, P0BD9, P0BDC, P0BDD, P0BDE, P0BE1,
P0BE2 AND P0BE3 are Type B DTCs.
Reference Information
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Circuit/System Verification
1. Clear the DTC information.
2. Ignition OFF for 1 minute.
3. Operate the vehicle under the Conditions for Running the DTC.
4. Retest for DTCs P0AEE, P0AEF, P0AF0, P0AF3, P0AF4, P0AF5, P0BD2, P0BD3, P0BD4, P0BD7, P0BD8, P0BD9, P0BDC, P0BDD,
P0BDE, P0BE1, P0BE2 AND P0BE3.
Circuit/System Testing
Program the PIM with the latest software version and recheck for DTCs.
If the DTC resets after programming or if the PIM already contains the latest software version, replace the PIM.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
Control Module References (See: Testing and Inspection/Programming and Relearning) for PIM replacement, setup, and programming.
P0BE6
DTC P0BE6-P0BE8, P0BEA-P0BEC, P0BEE, P0BEF, P0BF0, P0BF2-P0BF4, P0BF6-P0BF8, or P0BFA-P0BFC
Diagnostic Instructions
Showing posts with label P0BD3. Show all posts
Showing posts with label P0BD3. Show all posts
Wednesday, May 27, 2020
Tuesday, May 26, 2020
2010 Cadillac Truck Escalade RWD V8-6.2L Page 1169
2010 Cadillac Truck Escalade RWD V8-6.2L Page 1169
P0AEF, P0AF4, P0BD3, P0BD8, P0BDD, and P0BE2
The inverter phase temperature sensor is greater than 125掳C (275掳F) for 3 seconds.
P0AF0, P0AF5, P0BD4, P0BD9, P0BDE, and P0BE3
The inverter phase temperature sensor is less than -40掳C (-40掳F) for 3 seconds.
Action Taken When the DTC Sets
* DTCs P0AEE, P0AEF, P0AF0, P0AF3, P0AF4, P0AF5, P0BD2, P0BD3, P0BD4, P0BD7, P0BD8, P0BD9, P0BDC, P0BDD, P0BDE,
P0BE1, P0BE2 AND P0BE3 are Type B DTCs.
* The PIM commands the battery energy control module (BECM) to open the high voltage contactor relays.
Conditions for Clearing the DTC
DTCs P0AEE, P0AEF, P0AF0, P0AF3, P0AF4, P0AF5, P0BD2, P0BD3, P0BD4, P0BD7, P0BD8, P0BD9, P0BDC, P0BDD, P0BDE, P0BE1,
P0BE2 AND P0BE3 are Type B DTCs.
Reference Information
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Circuit/System Verification
1. Clear the DTC information.
2. Ignition OFF for 1 minute.
3. Operate the vehicle under the Conditions for Running the DTC.
4. Retest for DTCs P0AEE, P0AEF, P0AF0, P0AF3, P0AF4, P0AF5, P0BD2, P0BD3, P0BD4, P0BD7, P0BD8, P0BD9, P0BDC, P0BDD,
P0BDE, P0BE1, P0BE2 AND P0BE3.
Circuit/System Testing
Program the PIM with the latest software version and recheck for DTCs.
If the DTC resets after programming or if the PIM already contains the latest software version, replace the PIM.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
Control Module References (See: Testing and Inspection/Programming and Relearning) for PIM replacement, setup, and programming.
P0BD4
DTC P0AEE, P0AEF, P0AF0, P0AF3-P0AF5, P0BD2-P0BD4, P0BD7-P0BD9, P0BDC-P0BDE, or P0BE1-P0BE3
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptor
DTC P0AEE
- Drive Motor Inverter Temperature Sensor 1 Performance
DTC P0AEF
- Drive Motor Inverter Temperature Sensor 1 Circuit Low Voltage
DTC P0AF0
- Drive Motor Inverter Temperature Sensor 1 Circuit High Voltage
P0AEF, P0AF4, P0BD3, P0BD8, P0BDD, and P0BE2
The inverter phase temperature sensor is greater than 125掳C (275掳F) for 3 seconds.
P0AF0, P0AF5, P0BD4, P0BD9, P0BDE, and P0BE3
The inverter phase temperature sensor is less than -40掳C (-40掳F) for 3 seconds.
Action Taken When the DTC Sets
* DTCs P0AEE, P0AEF, P0AF0, P0AF3, P0AF4, P0AF5, P0BD2, P0BD3, P0BD4, P0BD7, P0BD8, P0BD9, P0BDC, P0BDD, P0BDE,
P0BE1, P0BE2 AND P0BE3 are Type B DTCs.
* The PIM commands the battery energy control module (BECM) to open the high voltage contactor relays.
Conditions for Clearing the DTC
DTCs P0AEE, P0AEF, P0AF0, P0AF3, P0AF4, P0AF5, P0BD2, P0BD3, P0BD4, P0BD7, P0BD8, P0BD9, P0BDC, P0BDD, P0BDE, P0BE1,
P0BE2 AND P0BE3 are Type B DTCs.
Reference Information
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Circuit/System Verification
1. Clear the DTC information.
2. Ignition OFF for 1 minute.
3. Operate the vehicle under the Conditions for Running the DTC.
4. Retest for DTCs P0AEE, P0AEF, P0AF0, P0AF3, P0AF4, P0AF5, P0BD2, P0BD3, P0BD4, P0BD7, P0BD8, P0BD9, P0BDC, P0BDD,
P0BDE, P0BE1, P0BE2 AND P0BE3.
Circuit/System Testing
Program the PIM with the latest software version and recheck for DTCs.
If the DTC resets after programming or if the PIM already contains the latest software version, replace the PIM.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
Control Module References (See: Testing and Inspection/Programming and Relearning) for PIM replacement, setup, and programming.
P0BD4
DTC P0AEE, P0AEF, P0AF0, P0AF3-P0AF5, P0BD2-P0BD4, P0BD7-P0BD9, P0BDC-P0BDE, or P0BE1-P0BE3
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptor
DTC P0AEE
- Drive Motor Inverter Temperature Sensor 1 Performance
DTC P0AEF
- Drive Motor Inverter Temperature Sensor 1 Circuit Low Voltage
DTC P0AF0
- Drive Motor Inverter Temperature Sensor 1 Circuit High Voltage
Thursday, November 7, 2019
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 1293
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 1293
P0AEF, P0AF4, P0BD3, P0BD8, P0BDD, and P0BE2
Ignition ON.
P0AF0, P0AF5, P0BD4, P0BD9, P0BDE, and P0BE3
* Ignition ON.
* Motor temperature is greater than -40掳C (-40掳F).
瀚慖f motor temperature is less than -40掳C (-40掳F) at Ignition ON, the drive motor must operate at greater than 20 Nm (14.75 lb ft) for a
cumulative time of 1.5 minutes before the DTC will run.
Conditions for Setting the DTC
P0AEE, P0AF3, P0BD2, P0BD7, P0BDC, and P0BE1
* A 15掳C ( 27掳F) difference is observed between the individual inverter phase temperature sensor and the average of all the inverter phase
temperatures.
* The above condition is present for 4 seconds.
P0AEF, P0AF4, P0BD3, P0BD8, P0BDD, and P0BE2
The inverter phase temperature sensor is greater than 125掳C (275掳F) for 3 seconds.
P0AF0, P0AF5, P0BD4, P0BD9, P0BDE, and P0BE3
The inverter phase temperature sensor is less than -40掳C (-40掳F) for 3 seconds.
Action Taken When the DTC Sets
* DTCs P0AEE, P0AEF, P0AF0, P0AF3, P0AF4, P0AF5, P0BD2, P0BD3, P0BD4, P0BD7, P0BD8, P0BD9, P0BDC, P0BDD, P0BDE,
P0BE1, P0BE2 AND P0BE3 are Type B DTCs.
* The PIM commands the battery energy control module (BECM) to open the high voltage contactor relays.
Conditions for Clearing the DTC
DTCs P0AEE, P0AEF, P0AF0, P0AF3, P0AF4, P0AF5, P0BD2, P0BD3, P0BD4, P0BD7, P0BD8, P0BD9, P0BDC, P0BDD, P0BDE, P0BE1,
P0BE2 AND P0BE3 are Type B DTCs.
Reference Information
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Circuit/System Verification
1. Clear the DTC information.
2. Ignition OFF for 1 minute.
3. Operate the vehicle under the Conditions for Running the DTC.
4. Retest for DTCs P0AEE, P0AEF, P0AF0, P0AF3, P0AF4, P0AF5, P0BD2, P0BD3, P0BD4, P0BD7, P0BD8, P0BD9, P0BDC, P0BDD,
P0BDE, P0BE1, P0BE2 AND P0BE3.
Circuit/System Testing
Program the PIM with the latest software version and recheck for DTCs.
If the DTC resets after programming or if the PIM already contains the latest software version, replace the PIM.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
Control Module References (See: Testing and Inspection/Programming and Relearning) for PIM replacement, setup, and programming.
P0BE6
DTC P0BE6-P0BE8, P0BEA-P0BEC, P0BEE, P0BEF, P0BF0, P0BF2-P0BF4, P0BF6-P0BF8, or P0BFA-P0BFC
Diagnostic Instructions
P0AEF, P0AF4, P0BD3, P0BD8, P0BDD, and P0BE2
Ignition ON.
P0AF0, P0AF5, P0BD4, P0BD9, P0BDE, and P0BE3
* Ignition ON.
* Motor temperature is greater than -40掳C (-40掳F).
瀚慖f motor temperature is less than -40掳C (-40掳F) at Ignition ON, the drive motor must operate at greater than 20 Nm (14.75 lb ft) for a
cumulative time of 1.5 minutes before the DTC will run.
Conditions for Setting the DTC
P0AEE, P0AF3, P0BD2, P0BD7, P0BDC, and P0BE1
* A 15掳C ( 27掳F) difference is observed between the individual inverter phase temperature sensor and the average of all the inverter phase
temperatures.
* The above condition is present for 4 seconds.
P0AEF, P0AF4, P0BD3, P0BD8, P0BDD, and P0BE2
The inverter phase temperature sensor is greater than 125掳C (275掳F) for 3 seconds.
P0AF0, P0AF5, P0BD4, P0BD9, P0BDE, and P0BE3
The inverter phase temperature sensor is less than -40掳C (-40掳F) for 3 seconds.
Action Taken When the DTC Sets
* DTCs P0AEE, P0AEF, P0AF0, P0AF3, P0AF4, P0AF5, P0BD2, P0BD3, P0BD4, P0BD7, P0BD8, P0BD9, P0BDC, P0BDD, P0BDE,
P0BE1, P0BE2 AND P0BE3 are Type B DTCs.
* The PIM commands the battery energy control module (BECM) to open the high voltage contactor relays.
Conditions for Clearing the DTC
DTCs P0AEE, P0AEF, P0AF0, P0AF3, P0AF4, P0AF5, P0BD2, P0BD3, P0BD4, P0BD7, P0BD8, P0BD9, P0BDC, P0BDD, P0BDE, P0BE1,
P0BE2 AND P0BE3 are Type B DTCs.
Reference Information
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Circuit/System Verification
1. Clear the DTC information.
2. Ignition OFF for 1 minute.
3. Operate the vehicle under the Conditions for Running the DTC.
4. Retest for DTCs P0AEE, P0AEF, P0AF0, P0AF3, P0AF4, P0AF5, P0BD2, P0BD3, P0BD4, P0BD7, P0BD8, P0BD9, P0BDC, P0BDD,
P0BDE, P0BE1, P0BE2 AND P0BE3.
Circuit/System Testing
Program the PIM with the latest software version and recheck for DTCs.
If the DTC resets after programming or if the PIM already contains the latest software version, replace the PIM.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
Control Module References (See: Testing and Inspection/Programming and Relearning) for PIM replacement, setup, and programming.
P0BE6
DTC P0BE6-P0BE8, P0BEA-P0BEC, P0BEE, P0BEF, P0BF0, P0BF2-P0BF4, P0BF6-P0BF8, or P0BFA-P0BFC
Diagnostic Instructions
Wednesday, November 6, 2019
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 1270
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 1270
P0AEF, P0AF4, P0BD3, P0BD8, P0BDD, and P0BE2
The inverter phase temperature sensor is greater than 125掳C (275掳F) for 3 seconds.
P0AF0, P0AF5, P0BD4, P0BD9, P0BDE, and P0BE3
The inverter phase temperature sensor is less than -40掳C (-40掳F) for 3 seconds.
Action Taken When the DTC Sets
* DTCs P0AEE, P0AEF, P0AF0, P0AF3, P0AF4, P0AF5, P0BD2, P0BD3, P0BD4, P0BD7, P0BD8, P0BD9, P0BDC, P0BDD, P0BDE,
P0BE1, P0BE2 AND P0BE3 are Type B DTCs.
* The PIM commands the battery energy control module (BECM) to open the high voltage contactor relays.
Conditions for Clearing the DTC
DTCs P0AEE, P0AEF, P0AF0, P0AF3, P0AF4, P0AF5, P0BD2, P0BD3, P0BD4, P0BD7, P0BD8, P0BD9, P0BDC, P0BDD, P0BDE, P0BE1,
P0BE2 AND P0BE3 are Type B DTCs.
Reference Information
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Circuit/System Verification
1. Clear the DTC information.
2. Ignition OFF for 1 minute.
3. Operate the vehicle under the Conditions for Running the DTC.
4. Retest for DTCs P0AEE, P0AEF, P0AF0, P0AF3, P0AF4, P0AF5, P0BD2, P0BD3, P0BD4, P0BD7, P0BD8, P0BD9, P0BDC, P0BDD,
P0BDE, P0BE1, P0BE2 AND P0BE3.
Circuit/System Testing
Program the PIM with the latest software version and recheck for DTCs.
If the DTC resets after programming or if the PIM already contains the latest software version, replace the PIM.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
Control Module References (See: Testing and Inspection/Programming and Relearning) for PIM replacement, setup, and programming.
P0BD4
DTC P0AEE, P0AEF, P0AF0, P0AF3-P0AF5, P0BD2-P0BD4, P0BD7-P0BD9, P0BDC-P0BDE, or P0BE1-P0BE3
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptor
DTC P0AEE
- Drive Motor Inverter Temperature Sensor 1 Performance
DTC P0AEF
- Drive Motor Inverter Temperature Sensor 1 Circuit Low Voltage
DTC P0AF0
- Drive Motor Inverter Temperature Sensor 1 Circuit High Voltage
P0AEF, P0AF4, P0BD3, P0BD8, P0BDD, and P0BE2
The inverter phase temperature sensor is greater than 125掳C (275掳F) for 3 seconds.
P0AF0, P0AF5, P0BD4, P0BD9, P0BDE, and P0BE3
The inverter phase temperature sensor is less than -40掳C (-40掳F) for 3 seconds.
Action Taken When the DTC Sets
* DTCs P0AEE, P0AEF, P0AF0, P0AF3, P0AF4, P0AF5, P0BD2, P0BD3, P0BD4, P0BD7, P0BD8, P0BD9, P0BDC, P0BDD, P0BDE,
P0BE1, P0BE2 AND P0BE3 are Type B DTCs.
* The PIM commands the battery energy control module (BECM) to open the high voltage contactor relays.
Conditions for Clearing the DTC
DTCs P0AEE, P0AEF, P0AF0, P0AF3, P0AF4, P0AF5, P0BD2, P0BD3, P0BD4, P0BD7, P0BD8, P0BD9, P0BDC, P0BDD, P0BDE, P0BE1,
P0BE2 AND P0BE3 are Type B DTCs.
Reference Information
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Circuit/System Verification
1. Clear the DTC information.
2. Ignition OFF for 1 minute.
3. Operate the vehicle under the Conditions for Running the DTC.
4. Retest for DTCs P0AEE, P0AEF, P0AF0, P0AF3, P0AF4, P0AF5, P0BD2, P0BD3, P0BD4, P0BD7, P0BD8, P0BD9, P0BDC, P0BDD,
P0BDE, P0BE1, P0BE2 AND P0BE3.
Circuit/System Testing
Program the PIM with the latest software version and recheck for DTCs.
If the DTC resets after programming or if the PIM already contains the latest software version, replace the PIM.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
Control Module References (See: Testing and Inspection/Programming and Relearning) for PIM replacement, setup, and programming.
P0BD4
DTC P0AEE, P0AEF, P0AF0, P0AF3-P0AF5, P0BD2-P0BD4, P0BD7-P0BD9, P0BDC-P0BDE, or P0BE1-P0BE3
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptor
DTC P0AEE
- Drive Motor Inverter Temperature Sensor 1 Performance
DTC P0AEF
- Drive Motor Inverter Temperature Sensor 1 Circuit Low Voltage
DTC P0AF0
- Drive Motor Inverter Temperature Sensor 1 Circuit High Voltage
Sunday, October 27, 2019
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1293
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1293
P0AEF, P0AF4, P0BD3, P0BD8, P0BDD, and P0BE2
Ignition ON.
P0AF0, P0AF5, P0BD4, P0BD9, P0BDE, and P0BE3
* Ignition ON.
* Motor temperature is greater than -40锟斤拷C (-40锟斤拷F).
锟斤拷If motor temperature is less than -40锟斤拷C (-40锟斤拷F) at Ignition ON, the drive motor must operate at greater than 20 Nm (14.75 lb ft) for a
cumulative time of 1.5 minutes before the DTC will run.
Conditions for Setting the DTC
P0AEE, P0AF3, P0BD2, P0BD7, P0BDC, and P0BE1
* A 15锟斤拷C ( 27锟斤拷F) difference is observed between the individual inverter phase temperature sensor and the average of all the inverter phase
temperatures.
* The above condition is present for 4 seconds.
P0AEF, P0AF4, P0BD3, P0BD8, P0BDD, and P0BE2
The inverter phase temperature sensor is greater than 125锟斤拷C (275锟斤拷F) for 3 seconds.
P0AF0, P0AF5, P0BD4, P0BD9, P0BDE, and P0BE3
The inverter phase temperature sensor is less than -40锟斤拷C (-40锟斤拷F) for 3 seconds.
Action Taken When the DTC Sets
* DTCs P0AEE, P0AEF, P0AF0, P0AF3, P0AF4, P0AF5, P0BD2, P0BD3, P0BD4, P0BD7, P0BD8, P0BD9, P0BDC, P0BDD, P0BDE,
P0BE1, P0BE2 AND P0BE3 are Type B DTCs.
* The PIM commands the battery energy control module (BECM) to open the high voltage contactor relays.
Conditions for Clearing the DTC
DTCs P0AEE, P0AEF, P0AF0, P0AF3, P0AF4, P0AF5, P0BD2, P0BD3, P0BD4, P0BD7, P0BD8, P0BD9, P0BDC, P0BDD, P0BDE, P0BE1,
P0BE2 AND P0BE3 are Type B DTCs.
Reference Information
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Circuit/System Verification
1. Clear the DTC information.
2. Ignition OFF for 1 minute.
3. Operate the vehicle under the Conditions for Running the DTC.
4. Retest for DTCs P0AEE, P0AEF, P0AF0, P0AF3, P0AF4, P0AF5, P0BD2, P0BD3, P0BD4, P0BD7, P0BD8, P0BD9, P0BDC, P0BDD,
P0BDE, P0BE1, P0BE2 AND P0BE3.
Circuit/System Testing
Program the PIM with the latest software version and recheck for DTCs.
If the DTC resets after programming or if the PIM already contains the latest software version, replace the PIM.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
Control Module References (See: Testing and Inspection/Programming and Relearning) for PIM replacement, setup, and programming.
P0BE6
DTC P0BE6-P0BE8, P0BEA-P0BEC, P0BEE, P0BEF, P0BF0, P0BF2-P0BF4, P0BF6-P0BF8, or P0BFA-P0BFC
Diagnostic Instructions
P0AEF, P0AF4, P0BD3, P0BD8, P0BDD, and P0BE2
Ignition ON.
P0AF0, P0AF5, P0BD4, P0BD9, P0BDE, and P0BE3
* Ignition ON.
* Motor temperature is greater than -40锟斤拷C (-40锟斤拷F).
锟斤拷If motor temperature is less than -40锟斤拷C (-40锟斤拷F) at Ignition ON, the drive motor must operate at greater than 20 Nm (14.75 lb ft) for a
cumulative time of 1.5 minutes before the DTC will run.
Conditions for Setting the DTC
P0AEE, P0AF3, P0BD2, P0BD7, P0BDC, and P0BE1
* A 15锟斤拷C ( 27锟斤拷F) difference is observed between the individual inverter phase temperature sensor and the average of all the inverter phase
temperatures.
* The above condition is present for 4 seconds.
P0AEF, P0AF4, P0BD3, P0BD8, P0BDD, and P0BE2
The inverter phase temperature sensor is greater than 125锟斤拷C (275锟斤拷F) for 3 seconds.
P0AF0, P0AF5, P0BD4, P0BD9, P0BDE, and P0BE3
The inverter phase temperature sensor is less than -40锟斤拷C (-40锟斤拷F) for 3 seconds.
Action Taken When the DTC Sets
* DTCs P0AEE, P0AEF, P0AF0, P0AF3, P0AF4, P0AF5, P0BD2, P0BD3, P0BD4, P0BD7, P0BD8, P0BD9, P0BDC, P0BDD, P0BDE,
P0BE1, P0BE2 AND P0BE3 are Type B DTCs.
* The PIM commands the battery energy control module (BECM) to open the high voltage contactor relays.
Conditions for Clearing the DTC
DTCs P0AEE, P0AEF, P0AF0, P0AF3, P0AF4, P0AF5, P0BD2, P0BD3, P0BD4, P0BD7, P0BD8, P0BD9, P0BDC, P0BDD, P0BDE, P0BE1,
P0BE2 AND P0BE3 are Type B DTCs.
Reference Information
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Circuit/System Verification
1. Clear the DTC information.
2. Ignition OFF for 1 minute.
3. Operate the vehicle under the Conditions for Running the DTC.
4. Retest for DTCs P0AEE, P0AEF, P0AF0, P0AF3, P0AF4, P0AF5, P0BD2, P0BD3, P0BD4, P0BD7, P0BD8, P0BD9, P0BDC, P0BDD,
P0BDE, P0BE1, P0BE2 AND P0BE3.
Circuit/System Testing
Program the PIM with the latest software version and recheck for DTCs.
If the DTC resets after programming or if the PIM already contains the latest software version, replace the PIM.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
Control Module References (See: Testing and Inspection/Programming and Relearning) for PIM replacement, setup, and programming.
P0BE6
DTC P0BE6-P0BE8, P0BEA-P0BEC, P0BEE, P0BEF, P0BF0, P0BF2-P0BF4, P0BF6-P0BF8, or P0BFA-P0BFC
Diagnostic Instructions
Saturday, October 26, 2019
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1270
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1270
P0AEF, P0AF4, P0BD3, P0BD8, P0BDD, and P0BE2
The inverter phase temperature sensor is greater than 125锟斤拷C (275锟斤拷F) for 3 seconds.
P0AF0, P0AF5, P0BD4, P0BD9, P0BDE, and P0BE3
The inverter phase temperature sensor is less than -40锟斤拷C (-40锟斤拷F) for 3 seconds.
Action Taken When the DTC Sets
* DTCs P0AEE, P0AEF, P0AF0, P0AF3, P0AF4, P0AF5, P0BD2, P0BD3, P0BD4, P0BD7, P0BD8, P0BD9, P0BDC, P0BDD, P0BDE,
P0BE1, P0BE2 AND P0BE3 are Type B DTCs.
* The PIM commands the battery energy control module (BECM) to open the high voltage contactor relays.
Conditions for Clearing the DTC
DTCs P0AEE, P0AEF, P0AF0, P0AF3, P0AF4, P0AF5, P0BD2, P0BD3, P0BD4, P0BD7, P0BD8, P0BD9, P0BDC, P0BDD, P0BDE, P0BE1,
P0BE2 AND P0BE3 are Type B DTCs.
Reference Information
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Circuit/System Verification
1. Clear the DTC information.
2. Ignition OFF for 1 minute.
3. Operate the vehicle under the Conditions for Running the DTC.
4. Retest for DTCs P0AEE, P0AEF, P0AF0, P0AF3, P0AF4, P0AF5, P0BD2, P0BD3, P0BD4, P0BD7, P0BD8, P0BD9, P0BDC, P0BDD,
P0BDE, P0BE1, P0BE2 AND P0BE3.
Circuit/System Testing
Program the PIM with the latest software version and recheck for DTCs.
If the DTC resets after programming or if the PIM already contains the latest software version, replace the PIM.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
Control Module References (See: Testing and Inspection/Programming and Relearning) for PIM replacement, setup, and programming.
P0BD4
DTC P0AEE, P0AEF, P0AF0, P0AF3-P0AF5, P0BD2-P0BD4, P0BD7-P0BD9, P0BDC-P0BDE, or P0BE1-P0BE3
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptor
DTC P0AEE
- Drive Motor Inverter Temperature Sensor 1 Performance
DTC P0AEF
- Drive Motor Inverter Temperature Sensor 1 Circuit Low Voltage
DTC P0AF0
- Drive Motor Inverter Temperature Sensor 1 Circuit High Voltage
P0AEF, P0AF4, P0BD3, P0BD8, P0BDD, and P0BE2
The inverter phase temperature sensor is greater than 125锟斤拷C (275锟斤拷F) for 3 seconds.
P0AF0, P0AF5, P0BD4, P0BD9, P0BDE, and P0BE3
The inverter phase temperature sensor is less than -40锟斤拷C (-40锟斤拷F) for 3 seconds.
Action Taken When the DTC Sets
* DTCs P0AEE, P0AEF, P0AF0, P0AF3, P0AF4, P0AF5, P0BD2, P0BD3, P0BD4, P0BD7, P0BD8, P0BD9, P0BDC, P0BDD, P0BDE,
P0BE1, P0BE2 AND P0BE3 are Type B DTCs.
* The PIM commands the battery energy control module (BECM) to open the high voltage contactor relays.
Conditions for Clearing the DTC
DTCs P0AEE, P0AEF, P0AF0, P0AF3, P0AF4, P0AF5, P0BD2, P0BD3, P0BD4, P0BD7, P0BD8, P0BD9, P0BDC, P0BDD, P0BDE, P0BE1,
P0BE2 AND P0BE3 are Type B DTCs.
Reference Information
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Circuit/System Verification
1. Clear the DTC information.
2. Ignition OFF for 1 minute.
3. Operate the vehicle under the Conditions for Running the DTC.
4. Retest for DTCs P0AEE, P0AEF, P0AF0, P0AF3, P0AF4, P0AF5, P0BD2, P0BD3, P0BD4, P0BD7, P0BD8, P0BD9, P0BDC, P0BDD,
P0BDE, P0BE1, P0BE2 AND P0BE3.
Circuit/System Testing
Program the PIM with the latest software version and recheck for DTCs.
If the DTC resets after programming or if the PIM already contains the latest software version, replace the PIM.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
Control Module References (See: Testing and Inspection/Programming and Relearning) for PIM replacement, setup, and programming.
P0BD4
DTC P0AEE, P0AEF, P0AF0, P0AF3-P0AF5, P0BD2-P0BD4, P0BD7-P0BD9, P0BDC-P0BDE, or P0BE1-P0BE3
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptor
DTC P0AEE
- Drive Motor Inverter Temperature Sensor 1 Performance
DTC P0AEF
- Drive Motor Inverter Temperature Sensor 1 Circuit Low Voltage
DTC P0AF0
- Drive Motor Inverter Temperature Sensor 1 Circuit High Voltage
Subscribe to:
Posts (Atom)