2010 Cadillac Truck SRX FWD V6-3.0L Page 1567

2010 Cadillac Truck SRX FWD V6-3.0L Page 1567

P0567

DTC P0564, P0567, or P0568

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions)provides an overview of each diagnostic category.

DTC Descriptors

DTC P0564

- Cruise Control Multifunction Switch Circuit

DTC P0567

- Cruise Control Resume Switch Circuit

DTC P0568

- Cruise Control Set Switch Circuit

Diagnostic Fault Information

Circuit/System Description

The cruise control switch is an input to the body control module (BCM). The BCM monitors the cruise control on/off, set/coast, resume/accelerate

and cancel switches via the cruise control switch signal circuit in order to detect when the driver has requested to perform a cruise control function.

The BCM detects a specific voltage signal on the cruise control switch signal circuit when a switch is applied. The BCM sends a serial data

message to the engine control module (ECM) indicating the status of the cruise control switches.

Conditions for Running the DTC

* The cruise switch is ON.

* The ignition is ON.

Conditions for Setting the DTC

* The BCM detects an invalid voltage signal on the cruise control switch signal circuit for greater than 2 seconds and sends a serial data

message to the ECM. The ECM sets these DTCs when the message is received.

* The ECM runs this diagnostic every 0.05 second.

Actions Taken When the DTC Sets

DTCs P0564, P0567, or P0568 are type C DTCs.

Conditions for Clearing the DTC

DTCs P0564, P0567, or P0568 are type C DTCs.

Reference Information

Schematic Reference

Cruise Control Schematics (See: Cruise Control/Diagrams/Electrical Diagrams)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)

Description and Operation

Cruise Control Description and Operation (See: Cruise Control/Description and Operation)

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 2504

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 2504

P0567

The ECM detects that the Resume switch is applied for longer than 90 seconds.

P0568

The ECM detects that the Set/Coast switch is applied for longer than 90 seconds.

Actions Taken When the DTC Sets

* The malfunction indicator lamp (MIL) will not illuminate.

* The cruise control system is disabled.

Conditions for Clearing the DTC

* The condition responsible for setting the DTC no longer exists.

* A history DTC will clear after 40 malfunction-free ignition cycles have occurred.

Reference Information

Schematic Reference

Cruise Control Schematics (See: Cruise Control/Diagrams/Electrical Diagrams)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Description and Operation

Cruise Control Description and Operation (See: Cruise Control/Description and Operation)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

Engine ON, while rotating the steering wheel to both steering stops, observe the scan tool Cruise Control Switch parameter while pressing each of

the cruise control switches. The parameter should toggle between On, Off, Resume, and Set as the applicable switch is pressed.

Circuit/System Testing

Cruise Control Switch Circuit Malfunction

1. Ignition OFF, disconnect the harness connector at the steering wheel controls switch - left.

2. Ignition ON, test for B+ between the B+ circuit terminal 1 and ground.

瀚慖f less than the specified value, test the circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the

BCM.

3. Test for B+ between the B+ circuit terminal 1 and the signal circuit terminal 3.

瀚慖f less than the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace

the BCM.

4. Ignition OFF, disconnect the X1 harness connector at the BCM.

5. Test for infinite resistance between the signal circuit terminal 3 and ground.

瀚慖f less than the specified value, test the signal circuit for a short to ground.

6. If all circuits test normal, test or replace the steering wheel control switch - left.