2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 87
If any of the DTCs are set, program the serial data gateway module. If any of the DTCs reset, replace the serial data gateway module.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
Control Module References (See: Testing and Inspection/Programming and Relearning) for serial data gateway module replacement, setup, and
programming
B009F
DTC B009F
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC B009F 00
- High Voltage Crash Impact Detection Sensor 1 No Additional Information
DTC B009F 11
- High Voltage Crash Impact Detection Sensor 1 Above Maximum Threshold
DTC B009F 12
- High Voltage Crash Impact Detection Sensor 1 Below Minimum Threshold
DTC B009F 39
- High Voltage Crash Impact Detection Sensor 1 Internal Electronic Failure
DTC B009F 3A
- High Voltage Crash Impact Detection Sensor 1 Incorrect Component Installed
DTC B009F 4A
- High Voltage Crash Impact Detection Sensor 1 Checksum Error
DTC B009F 73
- High Voltage Crash Impact Detection Sensor 1 Parity Error
Diagnostic Fault Information
Typical Scan Tool Data
Circuit/System Description
The high voltage circuit impact detector sensor utilizes a unidirectional 2-wire circuit. The high voltage circuit impact detector sensor modulates
current on the circuit interface to send ID, state of health, and collision status to the serial data gateway module. The serial data gateway module
Showing posts with label If any of the DTCs are set. Show all posts
Showing posts with label If any of the DTCs are set. Show all posts
Wednesday, September 9, 2020
Saturday, December 14, 2019
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 87
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 87
If any of the DTCs are set, program the serial data gateway module. If any of the DTCs reset, replace the serial data gateway module.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
Control Module References (See: Testing and Inspection/Programming and Relearning) for serial data gateway module replacement, setup, and
programming
B009F
DTC B009F
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC B009F 00
- High Voltage Crash Impact Detection Sensor 1 No Additional Information
DTC B009F 11
- High Voltage Crash Impact Detection Sensor 1 Above Maximum Threshold
DTC B009F 12
- High Voltage Crash Impact Detection Sensor 1 Below Minimum Threshold
DTC B009F 39
- High Voltage Crash Impact Detection Sensor 1 Internal Electronic Failure
DTC B009F 3A
- High Voltage Crash Impact Detection Sensor 1 Incorrect Component Installed
DTC B009F 4A
- High Voltage Crash Impact Detection Sensor 1 Checksum Error
DTC B009F 73
- High Voltage Crash Impact Detection Sensor 1 Parity Error
Diagnostic Fault Information
Typical Scan Tool Data
Circuit/System Description
The high voltage circuit impact detector sensor utilizes a unidirectional 2-wire circuit. The high voltage circuit impact detector sensor modulates
current on the circuit interface to send ID, state of health, and collision status to the serial data gateway module. The serial data gateway module
If any of the DTCs are set, program the serial data gateway module. If any of the DTCs reset, replace the serial data gateway module.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
Control Module References (See: Testing and Inspection/Programming and Relearning) for serial data gateway module replacement, setup, and
programming
B009F
DTC B009F
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC B009F 00
- High Voltage Crash Impact Detection Sensor 1 No Additional Information
DTC B009F 11
- High Voltage Crash Impact Detection Sensor 1 Above Maximum Threshold
DTC B009F 12
- High Voltage Crash Impact Detection Sensor 1 Below Minimum Threshold
DTC B009F 39
- High Voltage Crash Impact Detection Sensor 1 Internal Electronic Failure
DTC B009F 3A
- High Voltage Crash Impact Detection Sensor 1 Incorrect Component Installed
DTC B009F 4A
- High Voltage Crash Impact Detection Sensor 1 Checksum Error
DTC B009F 73
- High Voltage Crash Impact Detection Sensor 1 Parity Error
Diagnostic Fault Information
Typical Scan Tool Data
Circuit/System Description
The high voltage circuit impact detector sensor utilizes a unidirectional 2-wire circuit. The high voltage circuit impact detector sensor modulates
current on the circuit interface to send ID, state of health, and collision status to the serial data gateway module. The serial data gateway module
Thursday, December 5, 2019
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 678
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 678
If any of the DTCs are set, replace the battery in the appropriate keyless entry transmitter. Operate the transmitter 3 consecutive times. If the DTC
resets, replace the keyless entry transmitter.
Repair Instructions
Important: This vehicle may be equipped with the 2-Way Advanced Remote Start System. Vehicle equipped with the 2-Way Advanced
Remote Start System can be identified by an LCD screen on the keyless entry transmitter or a yellow label on the RCDLR. When servicing
the 2-Way Advanced Remote Start System, ensure that the correct parts are installed during replacement. Service parts for the 2-Way
Advanced Remote Start System can be found in the Accessory section of the parts manual.
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
Remote Control Door Lock Transmitter Programming (See: Accessories and Optional Equipment/Antitheft and Alarm Systems/Keyless
Entry/Keyless Entry Transmitter/Testing and Inspection)
B3130
DTC B3130 or B3135
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC B3130 00
- All Door Unlock Circuit
DTC B3135 00
- All Door Lock Circuit
Diagnostic Fault Information
Circuit/System Description
The LOCK/UNLOCK relay is controlled by the body control module (BCM) by providing voltage to one side of the relay or providing a ground to
the other side of the relay. During lock or unlock operation, battery voltage will be supplied to the lock actuators through the energized side of the
relay and grounded through the de-energized side of the relay.
Conditions for Running the DTC
The system voltage must be between 9-16 volts.
Conditions for Setting the DTC
B3130 00
The BCM detects a fault on the REAR DOOR LOCK/UNLOCK relay control circuit while commanding the rear doors to unlock.
If any of the DTCs are set, replace the battery in the appropriate keyless entry transmitter. Operate the transmitter 3 consecutive times. If the DTC
resets, replace the keyless entry transmitter.
Repair Instructions
Important: This vehicle may be equipped with the 2-Way Advanced Remote Start System. Vehicle equipped with the 2-Way Advanced
Remote Start System can be identified by an LCD screen on the keyless entry transmitter or a yellow label on the RCDLR. When servicing
the 2-Way Advanced Remote Start System, ensure that the correct parts are installed during replacement. Service parts for the 2-Way
Advanced Remote Start System can be found in the Accessory section of the parts manual.
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
Remote Control Door Lock Transmitter Programming (See: Accessories and Optional Equipment/Antitheft and Alarm Systems/Keyless
Entry/Keyless Entry Transmitter/Testing and Inspection)
B3130
DTC B3130 or B3135
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC B3130 00
- All Door Unlock Circuit
DTC B3135 00
- All Door Lock Circuit
Diagnostic Fault Information
Circuit/System Description
The LOCK/UNLOCK relay is controlled by the body control module (BCM) by providing voltage to one side of the relay or providing a ground to
the other side of the relay. During lock or unlock operation, battery voltage will be supplied to the lock actuators through the energized side of the
relay and grounded through the de-energized side of the relay.
Conditions for Running the DTC
The system voltage must be between 9-16 volts.
Conditions for Setting the DTC
B3130 00
The BCM detects a fault on the REAR DOOR LOCK/UNLOCK relay control circuit while commanding the rear doors to unlock.
Sunday, November 17, 2019
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 87
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 87
If any of the DTCs are set, program the serial data gateway module. If any of the DTCs reset, replace the serial data gateway module.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
Control Module References (See: Testing and Inspection/Programming and Relearning) for serial data gateway module replacement, setup, and
programming
B009F
DTC B009F
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC B009F 00
- High Voltage Crash Impact Detection Sensor 1 No Additional Information
DTC B009F 11
- High Voltage Crash Impact Detection Sensor 1 Above Maximum Threshold
DTC B009F 12
- High Voltage Crash Impact Detection Sensor 1 Below Minimum Threshold
DTC B009F 39
- High Voltage Crash Impact Detection Sensor 1 Internal Electronic Failure
DTC B009F 3A
- High Voltage Crash Impact Detection Sensor 1 Incorrect Component Installed
DTC B009F 4A
- High Voltage Crash Impact Detection Sensor 1 Checksum Error
DTC B009F 73
- High Voltage Crash Impact Detection Sensor 1 Parity Error
Diagnostic Fault Information
Typical Scan Tool Data
Circuit/System Description
The high voltage circuit impact detector sensor utilizes a unidirectional 2-wire circuit. The high voltage circuit impact detector sensor modulates
current on the circuit interface to send ID, state of health, and collision status to the serial data gateway module. The serial data gateway module
If any of the DTCs are set, program the serial data gateway module. If any of the DTCs reset, replace the serial data gateway module.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
Control Module References (See: Testing and Inspection/Programming and Relearning) for serial data gateway module replacement, setup, and
programming
B009F
DTC B009F
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC B009F 00
- High Voltage Crash Impact Detection Sensor 1 No Additional Information
DTC B009F 11
- High Voltage Crash Impact Detection Sensor 1 Above Maximum Threshold
DTC B009F 12
- High Voltage Crash Impact Detection Sensor 1 Below Minimum Threshold
DTC B009F 39
- High Voltage Crash Impact Detection Sensor 1 Internal Electronic Failure
DTC B009F 3A
- High Voltage Crash Impact Detection Sensor 1 Incorrect Component Installed
DTC B009F 4A
- High Voltage Crash Impact Detection Sensor 1 Checksum Error
DTC B009F 73
- High Voltage Crash Impact Detection Sensor 1 Parity Error
Diagnostic Fault Information
Typical Scan Tool Data
Circuit/System Description
The high voltage circuit impact detector sensor utilizes a unidirectional 2-wire circuit. The high voltage circuit impact detector sensor modulates
current on the circuit interface to send ID, state of health, and collision status to the serial data gateway module. The serial data gateway module
Subscribe to:
Posts (Atom)