CADILLAC: Connector End View Reference

Showing posts with label Connector End View Reference. Show all posts

Tuesday, March 8, 2022

2010 Cadillac Truck SRX FWD V6-3.0L Page 969

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

* Heated Oxygen Sensor Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical

Diagnostic Procedures/Wiring Repairs/Heated Oxygen Sensor Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

1. Ignition ON, observe the DTC information with a scan tool. Verify no B52 HO2S heater DTCs are set.

瀚慖f a B52 HO2S heater DTC is set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code

Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle).

2. Engine running, observe the appropriate scan tool B52 HO2S voltage parameter. The reading should be within the range of 50-1,050 mV.

3. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Verify none of the following conditions exist:

* Lean or rich fuel injectors-Refer to Fuel Injector Solenoid Coil Test (LAU) (See: Powertrain Management/Fuel Delivery and Air

Induction/Fuel Injector/Testing and Inspection)Fuel Injector Solenoid Coil Test (LF1, LFW) (See: Powertrain Management/Fuel

Delivery and Air Induction/Fuel Injector/Testing and Inspection).

* Water intrusion in the B52 HO2S harness connector

* Low or high fuel system pressure-Refer to Fuel System Diagnosis (LF1 China) (See: Powertrain Management/Fuel Delivery and Air

Induction/Fuel Pump/Testing and Inspection/Fuel System Diagnosis (China))Fuel System Diagnosis (LF1 Except China) (See:

Powertrain Management/Fuel Delivery and Air Induction/Fuel Pump/Testing and Inspection/Fuel System Diagnosis (Except China))Fuel

System Diagnosis (LAU China) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Pump/Testing and Inspection/Fuel

System Diagnosis (China))Fuel System Diagnosis (LAU Except China) (See: Powertrain Management/Fuel Delivery and Air

Induction/Fuel Pump/Testing and Inspection/Fuel System Diagnosis (Except China)).

* Fuel that is contaminated-Refer to Alcohol/Contaminants-in-Fuel Diagnosis (Special Tool) (See: Powertrain Management/Fuel Delivery

and Air Induction/Fuel/Testing and Inspection/Alcohol/Contaminants-in-Fuel Diagnosis (Special Tool))Alcohol/Contaminants-in-Fuel

Diagnosis (Without Special Tool) (See: Powertrain Management/Computers and Control Systems/Testing and Inspection/Component

Tests and General Diagnostics/Alcohol/Contaminants-in-Fuel Diagnosis (Without Special Tool)).

* Fuel saturation of the evaporative emission (EVAP) canister

* Exhaust leaks near the B52 HO2S

* Engine vacuum leaks

* Engine oil consumption-Refer to Oil Consumption Diagnosis (See: Engine, Cooling and Exhaust/Engine/Testing and

Inspection/Component Tests and General Diagnostics/Oil Consumption Diagnosis).

* Engine coolant consumption-Refer to Loss of Coolant (See: Engine, Cooling and Exhaust/Cooling System/Testing and

Inspection/Symptom Related Diagnostic Procedures/Loss of Coolant).

瀚慖f you find any of the above conditions, repair as necessary.

2. If all conditions test normal, test or replace the appropriate B52 HO2S.

Repair Instructions

Caution: Refer to Heated Oxygen Sensor Resistance Learn Reset Caution (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service Precautions/Heated Oxygen Sensor Resistance Learn Reset Caution).

Monday, February 28, 2022

2010 Cadillac Truck SRX FWD V6-3.0L Page 846

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)

Description and Operation

Electronic Suspension Control Description and Operation (See: Steering and Suspension/Suspension/Suspension Control ( Automatic - Electronic

)/Description and Operation)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

Ignition ON, with a scan tool, command the Damper Actuator Increase and Decrease while observing the Damper Actuator Command parameter.

The parameter should vary between 0-1000 mA. Listen/feel the Q37 shock absorber actuator. The component should activate when changing

between the commanded states.

Circuit/System Testing

1. Ignition OFF, disconnect the harness connector at the appropriate Q37 shock absorber actuator.

2. Perform this setup step in the following order:

1. Connect a test lamp and ammeter in series between both Q37 shock absorber actuator harness connector control circuit terminals.

2. Ignition ON, with a scan tool, attempt to clear all K19 suspension control module DTC's (codes may not clear).

3. With a scan tool, command the Damper Actuator to Increase the amperage to approximately 400 mA and Decrease to 0 mA while comparing

the ammeter displayed values and scan tool Damper Actuator Command parameter displayed values. Verify the following:

* The test lamp is illuminated.

* The ammeter displayed values and scan tool Damper Actuator Command parameter displayed values change and are simultaneously

within 15 mA of each other.

瀚慖f the test lamp is not illuminated and/or the values are not within the specified range, test both control circuits for a short to voltage, short

to ground, or open/high resistance. If all circuits test normal, replace the K19 suspension control module.

4. If all circuits test normal, test or replace the Q37 shock absorber actuator.

Component Testing

Static Test

1. Ignition OFF, disconnect the harness connector at the appropriate Q37 shock absorber actuator.

2. Test for 2-3 ohm between the Q37 shock absorber actuator control terminals.

瀚慖f not within the specified range, replace the Q37 shock absorber actuator.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Strut, Strut Component, or Spring Replacement (See: Steering and Suspension/Suspension/Suspension Spring ( Coil / Leaf )/Service and

Repair/Front Suspension Coil Spring)

* Shock Absorber Replacement (See: Steering and Suspension/Suspension/Suspension Strut / Shock Absorber/Service and Repair/Rear

Suspension Shock Absorber)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for suspension control module replacement, setup,

Saturday, February 26, 2022

2010 Cadillac Truck SRX FWD V6-3.0L Page 1159

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)

Description and Operation

Fuel System Description (LF1) (See: Powertrain Management/Fuel Delivery and Air Induction/Description and Operation/Fuel System

Description)Fuel System Description (LAU or LY7) (See: Powertrain Management/Fuel Delivery and Air Induction/Description and

Operation/Fuel System Description)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

1. Observe the DTC information with a scan tool. DTC P0685 or P1682 should not set.

瀚慖f a DTC is set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code Descriptions/Diagnostic Trouble

Code (DTC) List - Vehicle).

2. Engine operating, observe the DTC information with a scan tool. DTC P1248, P1249, P124A, P124B, P124C, or P124D should not set.

3. Observe the scan tool Current Misfire Counter parameters. The Current Misfire Counters should not increment.

4. Ignition ON, observe the scan tool Cylinder 1-6 Injector Control Circuit Status parameters. Verify the Injector Control Circuit Status

parameters display OK.

5. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Ignition OFF, disconnect the appropriate multi-way harness connector X198 or X199, at the rear of the intake manifold.

2. Ignition ON, observe the appropriate scan tool Cylinder 1-6 Injector Control Circuit Status. The parameter should display Open.

瀚慖f not the specified value, test the appropriate high voltage supply circuit, ECM side, for a short to ground or the appropriate high voltage

control circuit, ECM side, for a short to voltage. If the circuits test normal, replace the K20 ECM.

3. Ignition ON, connect a test lamp between the appropriate high voltage supply circuit and the high voltage control circuit. The Injector

Control Circuit Status should transition from Open to OK.

瀚慖f not the specified value, test for the following conditions in the ECM side of the harness:

* An open/high resistance in the high voltage supply circuit

* An open/high resistance in the high voltage control circuit

* A short to ground in the high voltage control circuit

* A short to voltage in the high voltage supply circuit

瀚慖f the circuits test normal, replace the K20 ECM.

Note: Testing for the following steps is performed on the fuel injector side of the multi-way harness connector. It may be necessary to

remove the intake manifold to isolate the condition.

4. Ignition OFF, measure the resistance between the appropriate high voltage supply circuit and ground. The DMM should display OL ohm.

瀚慖f less than the specified range, test the high voltage supply circuit and the high voltage control circuit for a short to ground. If the

circuits/connections test normal, test or replace the appropriate Q17 fuel injector(s).

5. Test for 2-3 ohm between the appropriate high voltage supply circuit and high voltage control circuit.

Tuesday, February 8, 2022

2010 Cadillac Truck SRX FWD V6-3.0L Page 1162

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)

Description and Operation

Fuel System Description (LF1) (See: Powertrain Management/Fuel Delivery and Air Induction/Description and Operation/Fuel System

Description)Fuel System Description (LAU or LY7) (See: Powertrain Management/Fuel Delivery and Air Induction/Description and

Operation/Fuel System Description)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

1. Observe the DTC information with a scan tool. DTC P0685 or P1682 should not set.

瀚慖f a DTC is set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code Descriptions/Diagnostic Trouble

Code (DTC) List - Vehicle).

2. Engine operating, observe the DTC information with a scan tool. DTC P1248, P1249, P124A, P124B, P124C, or P124D should not set.

3. Observe the scan tool Current Misfire Counter parameters. The Current Misfire Counters should not increment.

4. Ignition ON, observe the scan tool Cylinder 1-6 Injector Control Circuit Status parameters. Verify the Injector Control Circuit Status

parameters display OK.

5. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Ignition OFF, disconnect the appropriate multi-way harness connector X198 or X199, at the rear of the intake manifold.

2. Ignition ON, observe the appropriate scan tool Cylinder 1-6 Injector Control Circuit Status. The parameter should display Open.

瀚慖f not the specified value, test the appropriate high voltage supply circuit, ECM side, for a short to ground or the appropriate high voltage

control circuit, ECM side, for a short to voltage. If the circuits test normal, replace the K20 ECM.

3. Ignition ON, connect a test lamp between the appropriate high voltage supply circuit and the high voltage control circuit. The Injector

Control Circuit Status should transition from Open to OK.

瀚慖f not the specified value, test for the following conditions in the ECM side of the harness:

* An open/high resistance in the high voltage supply circuit

* An open/high resistance in the high voltage control circuit

* A short to ground in the high voltage control circuit

* A short to voltage in the high voltage supply circuit

瀚慖f the circuits test normal, replace the K20 ECM.

Note: Testing for the following steps is performed on the fuel injector side of the multi-way harness connector. It may be necessary to

remove the intake manifold to isolate the condition.

4. Ignition OFF, measure the resistance between the appropriate high voltage supply circuit and ground. The DMM should display OL ohm.

瀚慖f less than the specified range, test the high voltage supply circuit and the high voltage control circuit for a short to ground. If the

circuits/connections test normal, test or replace the appropriate Q17 fuel injector(s).

5. Test for 2-3 ohm between the appropriate high voltage supply circuit and high voltage control circuit.

Wednesday, January 12, 2022

2010 Cadillac Truck SRX FWD V6-3.0L Page 1156

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)

Description and Operation

Fuel System Description (LF1) (See: Powertrain Management/Fuel Delivery and Air Induction/Description and Operation/Fuel System

Description)Fuel System Description (LAU or LY7) (See: Powertrain Management/Fuel Delivery and Air Induction/Description and

Operation/Fuel System Description)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

1. Observe the DTC information with a scan tool. DTC P0685 or P1682 should not set.

瀚慖f a DTC is set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code Descriptions/Diagnostic Trouble

Code (DTC) List - Vehicle).

2. Engine operating, observe the DTC information with a scan tool. DTC P1248, P1249, P124A, P124B, P124C, or P124D should not set.

3. Observe the scan tool Current Misfire Counter parameters. The Current Misfire Counters should not increment.

4. Ignition ON, observe the scan tool Cylinder 1-6 Injector Control Circuit Status parameters. Verify the Injector Control Circuit Status

parameters display OK.

5. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Ignition OFF, disconnect the appropriate multi-way harness connector X198 or X199, at the rear of the intake manifold.

2. Ignition ON, observe the appropriate scan tool Cylinder 1-6 Injector Control Circuit Status. The parameter should display Open.

瀚慖f not the specified value, test the appropriate high voltage supply circuit, ECM side, for a short to ground or the appropriate high voltage

control circuit, ECM side, for a short to voltage. If the circuits test normal, replace the K20 ECM.

3. Ignition ON, connect a test lamp between the appropriate high voltage supply circuit and the high voltage control circuit. The Injector

Control Circuit Status should transition from Open to OK.

瀚慖f not the specified value, test for the following conditions in the ECM side of the harness:

* An open/high resistance in the high voltage supply circuit

* An open/high resistance in the high voltage control circuit

* A short to ground in the high voltage control circuit

* A short to voltage in the high voltage supply circuit

瀚慖f the circuits test normal, replace the K20 ECM.

Note: Testing for the following steps is performed on the fuel injector side of the multi-way harness connector. It may be necessary to

remove the intake manifold to isolate the condition.

4. Ignition OFF, measure the resistance between the appropriate high voltage supply circuit and ground. The DMM should display OL ohm.

瀚慖f less than the specified range, test the high voltage supply circuit and the high voltage control circuit for a short to ground. If the

circuits/connections test normal, test or replace the appropriate Q17 fuel injector(s).

5. Test for 2-3 ohm between the appropriate high voltage supply circuit and high voltage control circuit.

Sunday, January 2, 2022

2010 Cadillac Truck SRX FWD V6-3.0L Page 813

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)

Description and Operation

Brake Assist System Description and Operation (See: Brakes and Traction Control/Hydraulic System/Description and Operation/Brake Assist

System)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning)

Circuit/System Testing

1. Ignition ON, verify that DTC C1100 is not present.

瀚慖f DTC C1100 is present, refer to DTC C1100 (See: C Code Charts/C1100).

2. Inspect the brake booster vacuum system for damage, leakage and correct installation. Refer to Brake Assist System Diagnosis (See: Brakes

and Traction Control/Hydraulic System/Testing and Inspection/Component Tests and General Diagnostics/Brake Assist System Diagnosis).

3. If the brake booster vacuum systems diagnoses normal, replace the B19B Brake Booster Vacuum Sensor and verify the DTC does not reset.

If the DTC resets, replace the K17 Electronic Brake Control Module (EBCM).

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests)

* Power Brake Booster Vacuum Sensor Replacement (See: Brakes and Traction Control/Power Brake Assist/Brake Booster Vacuum

Sensor/Service and Repair)

* Control Module References (See: Testing and Inspection/Programming and Relearning)

C0393

DTC C0393

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptor

DTC C0393 0B

- Rear Axle Coupling Solenoid Valve Control Circuit High Current

Diagnostic Fault Information

Circuit/System Description

The rear differential clutch solenoid valve is mounted on the rear of the differential housing. The rear differential clutch control module supplies

Wednesday, May 19, 2021

2010 Cadillac CTS Sedan AWD V6-3.6L Page 880

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Description and Operation

Camshaft Actuator System Description (See: Powertrain Management/Computers and Control Systems/Description and Operation/Camshaft

Actuator System Description)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit

Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Wiring Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Testing

1. Ignition ON, observe the DTC information with a scan tool. Verify that none of the following DTCs are set. DTC P0010, P0013, P0020,

P0023, P0335, P0336, P0338, P0341, P0342, P0343, P0346, P0347, P0348, P0366, P0367, P0368, P0391, P0392, P0393, P2088, P2089,

P2090, P2091, P2092, P2093, P2094, or P2095.

瀚慖f any of the DTCs listed are set refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code

Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle) for further diagnosis.

2. Idle the engine at normal operating temperature for 10 minutes. DTCs P0016, P0017, P0018, or P0019 should not set.

瀚慖f a DTC sets, inspect for the following and repair as necessary:

* The correct installation of the camshaft sensors

* The correct installation of the crankshaft sensor

* A timing chain tensioner condition

* An incorrectly installed timing chain

* Excessive play in the timing chain

* A mechanical cam actuator that is stuck in the full advance or retard position.

* A timing chain that jumped teeth

* A crankshaft reluctor wheel that has moved in relationship to top dead center (TDC) on the crankshaft

3. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Timing Chain Alignment Diagram (See: Engine, Cooling and Exhaust/Engine/Timing Components/Timing Component Alignment

Marks/Locations)

* Camshaft Timing Drive Components Cleaning and Inspection (See: Engine, Cooling and Exhaust/Engine/Service and Repair/Overhaul/67.

Camshaft Timing Drive Components Cleaning and Inspection)

* Crankshaft and Bearing Cleaning and Inspection (See: Engine, Cooling and Exhaust/Engine/Service and Repair/Overhaul/52. Crankshaft

and Bearing Cleaning and Inspection)

P16F3

DTC P0601-P0604, P0606, P0607, P0610, P062B, P062F, P0630, P16F3, or P2610 (ECM, LF1)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

Saturday, May 1, 2021

2010 Cadillac CTS Sedan AWD V6-3.6L Page 371

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Description and Operation

Memory Seats Description and Operation (See: Body and Frame/Seats/Description and Operation/Memory Seats)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit

Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Wiring Repairs/Wiring Repairs)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Testing

1. Ignition OFF, disconnect the harness connector for all position sensors connected to the 5-volt reference circuit.

2. Ignition ON, observe all scan tool sensor parameters for Seat 1 and Column Info. The readings should be 0.0 volts.

瀚慖f greater than the specified value, test the appropriate signal circuit listed below for a short to voltage. If the circuit tests normal, replace

the MSM.

* Seat horizontal position sensor terminal B X2

* Seat front vertical position sensor terminal B X2

* Seat rear vertical position sensor terminal B X2

* Recline position sensor terminal 2

* Lumbar horizontal position sensor terminal E

* Steering column telescope position sensor terminal D X2

* Steering column tilt position sensor terminal A X2

3. Ignition ON, test for 4.8-5.2 volts between the 5-volt reference circuit at any one of the position sensors and ground.

瀚慖f less than the specified value, test the 5-volt reference circuit for a short to ground or an open/high resistance. If the circuit tests normal,

replace the MSM.

瀚慖f greater than the specified value, test the 5-volt reference circuit for a short to voltage. If the circuit tests normal, replace the MSM.

4. Connect each position sensor one at a time and verify that the DTC does not set as current.

瀚慖f the DTC sets as current, replace the appropriate position sensor.

5. If all circuits test normal, replace the MSM.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Front Seat Tilt Adjuster Actuator Replacement (See: Body and Frame/Seats/Power Seat Motor/Service and Repair/Front Seat Tilt Adjuster

Actuator Replacement)

* Front Seat Adjuster Actuator Replacement (See: Body and Frame/Seats/Power Seat Motor/Service and Repair/Front Seat Adjuster Actuator

Replacement)

* Driver Seat Outer Adjuster Rear Vertical Actuator Replacement (See: Body and Frame/Seats/Power Seat Motor/Service and Repair/Driver

Seat Outer Adjuster Rear Vertical Actuator Replacement)

* Seat Lumbar Sub System Replacement (without AHS) (See: Body and Frame/Seats/Service and Repair/Seat Lumbar Sub System

Replacement (Without AHS))Seat Lumbar Sub System Replacement (with AHS) (See: Body and Frame/Seats/Service and Repair/Seat

Lumbar Sub System Replacement (With AHS))

* Front Seat Recliner Actuator Motor Replacement (See: Body and Frame/Seats/Power Seat Motor/Service and Repair/Front Seat Recliner

Actuator Motor Replacement)

* Steering Column Tilt Wheel Position Sensor Replacement (See: Sensors and Switches/Sensors and Switches - Steering and

Suspension/Sensors and Switches - Steering/Tilt Wheel Sensor/Service and Repair)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for MSM replacement, setup, and programming

Tuesday, April 6, 2021

2010 Cadillac CTS Sedan AWD V6-3.6L Page 562

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Description and Operation

Keyless Entry System Description and Operation (with RPO Y41) (See: Accessories and Optional Equipment/Antitheft and Alarm

Systems/Keyless Entry/Description and Operation/Keyless Entry System Description and Operation (with RPO Y41))Keyless Entry System

Description and Operation (without RPO Y41) (See: Accessories and Optional Equipment/Antitheft and Alarm Systems/Keyless

Entry/Description and Operation/Keyless Entry System Description and Operation (without RPO Y41))

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit

Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Wiring Repairs/Wiring Repairs)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Testing

1. Ignition OFF, disconnect the harness connector at the LF door handle antenna.

2. Ignition ON, verify a test lamp does not illuminate between the signal circuit terminal A and ground.

瀚慖f the test lamp illuminates, test the signal circuit for a short to voltage. If the circuit tests normal, replace the RCDLR.

3. Install a DMM between the signal circuit terminal A and the low reference circuit terminal B. Set the DMM to capture AC voltage using the

MIN MAX function.

4. Perform the Driver Front Exterior Zone special functions test. Verify the DMM captured an AC voltage signal.

瀚慖f an AC voltage was not captured, test the signal circuit and the low reference circuit for a short to ground or an open/high resistance. If

the circuits test normal, replace the RCDLR.

5. If all circuits test normal, test or replace the LF door handle assembly.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Front Side Door Outside Handle Replacement (Front and Rear Doors with ATH) (See: Body and Frame/Doors, Hood and

Trunk/Doors/Front Door/Front Door Handle/Front Door Exterior Handle/Service and Repair)Front Side Door Outside Handle Replacement

(Front Door with ATH) (See: Body and Frame/Doors, Hood and Trunk/Doors/Front Door/Front Door Handle/Front Door Exterior

Handle/Service and Repair)Front Side Door Outside Handle Replacement (Without ATH) (See: Body and Frame/Doors, Hood and

Trunk/Doors/Front Door/Front Door Handle/Front Door Exterior Handle/Service and Repair)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for RCDLR replacement, setup, and programming

B3120

DTC B3120

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC B3120 00

- Keyless Entry Antenna 2 Performance - RF Door Antenna

Diagnostic Fault Information

Tuesday, March 30, 2021

2010 Cadillac CTS Sedan AWD V6-3.6L Page 748

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Description and Operation

Electronic Suspension Control Description and Operation (See: Steering and Suspension/Suspension/Suspension Control ( Automatic - Electronic

)/Description and Operation)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit

Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Wiring Repairs/Wiring Repairs)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

Ignition ON, observe the scan tool Position Sensor Data parameters while the vehicle is jounced. The readings should vary between 0.35-4.75 volts.

Circuit/System Testing

1. Ignition OFF, disconnect the harness connector at the appropriate suspension position sensor.

2. Ignition OFF, test for less than 1 ohm between the low reference circuit terminal C and ground.

瀚慖f greater than the specified range, test the low reference circuit for an open/high resistance. If circuit tests normal, replace the ESC

module.

3. Ignition ON, test for 4.8-5.2 volts between the 5-volt reference circuit terminal A and ground.

瀚慖f less than the specified range, test the 5-volt reference circuit for a short to ground or an open/high resistance. If the circuit tests normal,

replace the ESC module.

瀚慖f greater than the specified range, test the 5-volt reference circuit for a short to voltage. If the circuit tests normal, replace the ESC

module.

4. Verify the scan tool position sensor parameter is less than 0.35 volt.

瀚慖f greater than the specified range, test the signal circuit terminal B for a short to voltage. If the circuit tests normal, replace the ESC

module.

5. Install a 3A fused jumper wire between the signal circuit terminal B and the 5-volt reference circuit terminal A. Verify the scan tool position

sensor parameter is greater than 4.75 volts.

瀚慖f less that the specified range, test the signal circuit for a short to ground or an open high resistance. If all circuits test normal replace the

ESC module.

6. If all circuits test normal, test or replace the applicable suspension position sensor.

Component Testing

1. Install a 3A fused jumper wire between the 5-volt reference terminal A and 5 volts. Install a jumper wire between the low reference terminal

C and ground.

2. Sweep the suspension position sensor through the entire range while monitoring the voltage between the signal terminal B and the low

reference terminal C. The range should vary between 0.35-4.75 volts without any spikes or dropouts.

瀚慖f not within the specified range or if it is erratic, replace the suspension position sensor.

Repair Instructions

* Electronic Suspension Front Position Sensor Replacement (See: Sensors and Switches/Sensors and Switches - Steering and

Suspension/Sensors and Switches - Suspension/Ride Height Sensor/Service and Repair/Electronic Suspension Front Position Sensor

Replacement)

* Electronic Suspension Rear Position Sensor Replacement (See: Sensors and Switches/Sensors and Switches - Steering and

Suspension/Sensors and Switches - Suspension/Ride Height Sensor/Service and Repair/Electronic Suspension Rear Position Sensor

Replacement)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for ESC replacement, setup, and programming

Friday, February 12, 2021

2010 Cadillac CTS Sedan AWD V6-3.6L Page 140

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Description and Operation

SIR System Description and Operation (See: Restraints and Safety Systems/Air Bag Systems/Description and Operation/SIR System Description

and Operation)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit Testing/Circuit Testing)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit

Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Wiring Repairs/Wiring Repairs)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Connector Repairs/Connector Repairs)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

1. Ignition OFF, verify that the vehicle does not show any signs of inflator module or pretensioner deployment.

瀚慖f the vehicle displays any signs of inflator deployment, refer to Repairs and Inspections Required After a Collision (See: Body and

Frame/Repairs and Inspections Required After a Collision/Service and Repair).

2. Verify DTC B0052, B0053, or B0055 is not set.

瀚慖f DTC is set , refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code Descriptions/Diagnostic Trouble

Code (DTC) List - Vehicle).

3. Clear DTCs. Verify DTC B0056, B0057, or B0058 is not set.

瀚慖f any of the DTCs are set, replace the SDM.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* SIR/SRS Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Wiring Repairs/SIR/SRS Wiring Repairs)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for SDM replacement, setup, and programming

B0057

DTC B0056-B0058

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC B0056 00

- Passenger Frontal Airbag Suppressed

DTC B0057 00

- Passenger Side Airbag Suppressed

DTC B0058 00

- Passenger Pretensioner Suppressed

Circuit/System Description

When the ignition is turned ON, the passenger presence system (PPS) and the inflatable restraint sensing and diagnostic module (SDM) performs

Saturday, January 9, 2021

2010 Cadillac Truck SRX AWD V6-3.0L Page 1043

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)

Description and Operation

Turbocharger System Description ()

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

Note: If any Turbocharger circuit DTC is set, the Bypass Solenoid Valve output control may not function. It may be necessary to clear the

DTCs with a scan tool to enable the output control.

1. Ignition ON, observe the DTC information with a scan tool. Verify that DTC P0234, P0299, P0236, P0237, P0238, P0244, P0245, or P0246

is not set.

瀚慖f a DTC is set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code Descriptions/Diagnostic Trouble

Code (DTC) List - Vehicle) for further diagnosis.

2. Ignition ON, command the Turbocharger Bypass Solenoid Valve between Inactive and Active with a scan tool. You should hear an audible

click.

3. Engine running, command the Turbocharger Bypass Solenoid Valve between Inactive and Active with a scan tool while observing the

following control circuit status parameters:

* Turbocharger Bypass Solenoid Valve Control Circuit High Voltage Test Status

* Turbocharger Bypass Solenoid Valve Control Circuit Open Test Status

* Turbocharger Bypass Solenoid Valve Control Circuit Low Voltage Test Status

The parameters should alternate between OK and Not Run with each change in command.

4. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Ignition OFF, disconnect the harness connector at the Q40 turbocharger bypass solenoid valve.

2. Ignition ON, verify that a test lamp illuminates between the ignition circuit terminal 1 and ground.

瀚慖f the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit tests normal and

the ignition voltage circuit fuse is open, test all components connected to the ignition voltage circuit and replace as necessary.

3. Connect a test lamp between the control circuit terminal 2 and the ignition circuit terminal 1.

Note: If any Turbocharger circuit DTC is set, the Bypass Solenoid Valve output control may not function. It may be necessary to clear the

DTCs with a scan tool to enable the output control.

4. Command the Turbocharger Bypass Solenoid Valve between Inactive and Active with a scan tool, then select exit. The test lamp should

illuminate and then go OFF.

瀚慖f the test lamp is always ON, test the control circuit terminal 2 for a short to ground. If the circuit tests normal, replace the K20 ECM.

瀚慖f the test lamp is always OFF, test the control circuit terminal 2 for a short to voltage or an open/high resistance. If the circuit tests

normal, replace the K20 ECM.

Thursday, December 31, 2020

2010 Cadillac Truck SRX AWD V6-3.0L Page 858

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)

Description and Operation

Electronic Suspension Control Description and Operation (See: Steering and Suspension/Suspension/Suspension Control ( Automatic - Electronic

)/Description and Operation)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

Ignition ON, observe the scan tool Vertical Wheel Acceleration parameters. The parameters should be 0 m/s(2) when the vehicle is parked on a

level surface.

Circuit/System Testing

1. Ignition ON, verify that DTC C0870 is not present.

瀚慖f the DTC is present, refer to DTC C0870 (See: C Code Charts/C0870) to diagnose that DTC prior to this diagnostic.

2. Ignition OFF, disconnect the harness connector at the appropriate B161 vertical suspension acceleration sensor.

3. Ignition OFF, open/close doors, and wait 60 seconds. Test for less than 5 ohm between the low reference circuit terminal C and ground.

瀚慖f greater than the specified value, test the low reference circuit for short to voltage or an open/high resistance. If the circuit tests normal,

replace the K19 Suspension Control Module.

4. Ignition ON, test for 4.8-5.2 V between the 5 V reference circuit terminal A and ground.

瀚慖f less than the specified range, test the 5 V reference circuit for a short to ground or an open/high resistance. If the circuit tests normal,

replace the K19 suspension control module.

瀚慖f greater than the specified range, test the 5 V reference circuit for a short to voltage. If the circuit tests normal, replace the K19

suspension control module.

5. Test for 4.8-5.2 V between the signal circuit terminal B and ground.

瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace

the K19 suspension control module.

瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the K19 suspension

control module.

6. If all circuits test normal, replace the B161 vertical suspension acceleration sensor. Verify the DTC does not reset. If the DTC resets, replace

the K19 suspension control module

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Electronic Suspension Front Vertical Accelerometer Replacement - Lower (See: Sensors and Switches/Sensors and Switches - Steering and

Suspension/Sensors and Switches - Suspension/Acceleration Sensor/Service and Repair/Electronic Suspension Front Vertical Accelerometer

Replacement - Lower)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for suspension control module replacement, setup

Sunday, December 13, 2020

2010 Cadillac Truck SRX AWD V6-3.0L Page 552

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)

Description and Operation

OnStar Description and Operation (See: Accessories and Optional Equipment/Description and Operation/OnStar)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Special Tools

EL-49903 GM OnStar Antenna Diagnostic Tool Kit

Circuit/System Verification

Verify that the T4G cellular phone antenna and T4G cellular phone antenna coupling assembly are not damaged.

If the antenna assembly is damaged, replace the T4G cellular phone antenna.

Circuit/System Testing

1. Ignition OFF, disconnect both the GPS and cell coax cable connectors at the K73 telematics communication interface control module.

2. Connect the EL-49903 to the K73 telematics communication interface control module.

3. Clear the DTCs and operate the vehicle within the conditions for running the DTC. Verify DTC B2470 does not set.

瀚慖f the DTC sets, replace the K73 telematics communication interface control module.

4. Ignition OFF, disconnect the EL-49903 from the K73 telematics communication interface control module, and the antenna coax from the

T4G cellular phone antenna.

5. Ignition ON, test for less than 1 V between the antenna coax center terminal and ground.

瀚慖f greater than the specified range, replace the antenna coax.

6. Ignition ON, test for less than 1 V between the antenna coax outer shield and ground.

瀚慖f greater than the specified range, replace the antenna coax.

7. Test for infinite resistance between the antenna coax center terminal and ground.

瀚慖f less than the specified value, replace the antenna coax.

8. Test for infinite resistance between the antenna coax outer shield and ground.

瀚慖f less than the specified value, replace the antenna coax.

9. Test for less than 5 Ohms at the cellular antenna coax center terminal from end to end.

瀚慖f greater than specified value, replace the antenna coax.

10. Test for less than 5 Ohms at the cellular antenna coax outer shield from end to end.

瀚慖f greater than specified value, replace the antenna coax.

11. Test for infinite resistance between the antenna coax center terminal and the outer shield.

瀚慖f less than specified value, replace the antenna coax.

12. If coax cable tests normal, replace the T4G cellular phone antenna.

Friday, December 11, 2020

2010 Cadillac Truck SRX AWD V6-3.0L Page 1156

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)

Description and Operation

Fuel System Description (LF1) (See: Powertrain Management/Fuel Delivery and Air Induction/Description and Operation/Fuel System

Description)Fuel System Description (LAU or LY7) (See: Powertrain Management/Fuel Delivery and Air Induction/Description and

Operation/Fuel System Description)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

1. Observe the DTC information with a scan tool. DTC P0685 or P1682 should not set.

瀚慖f a DTC is set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code Descriptions/Diagnostic Trouble

Code (DTC) List - Vehicle).

2. Engine operating, observe the DTC information with a scan tool. DTC P1248, P1249, P124A, P124B, P124C, or P124D should not set.

3. Observe the scan tool Current Misfire Counter parameters. The Current Misfire Counters should not increment.

4. Ignition ON, observe the scan tool Cylinder 1-6 Injector Control Circuit Status parameters. Verify the Injector Control Circuit Status

parameters display OK.

5. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Ignition OFF, disconnect the appropriate multi-way harness connector X198 or X199, at the rear of the intake manifold.

2. Ignition ON, observe the appropriate scan tool Cylinder 1-6 Injector Control Circuit Status. The parameter should display Open.

瀚慖f not the specified value, test the appropriate high voltage supply circuit, ECM side, for a short to ground or the appropriate high voltage

control circuit, ECM side, for a short to voltage. If the circuits test normal, replace the K20 ECM.

3. Ignition ON, connect a test lamp between the appropriate high voltage supply circuit and the high voltage control circuit. The Injector

Control Circuit Status should transition from Open to OK.

瀚慖f not the specified value, test for the following conditions in the ECM side of the harness:

* An open/high resistance in the high voltage supply circuit

* An open/high resistance in the high voltage control circuit

* A short to ground in the high voltage control circuit

* A short to voltage in the high voltage supply circuit

瀚慖f the circuits test normal, replace the K20 ECM.

Note: Testing for the following steps is performed on the fuel injector side of the multi-way harness connector. It may be necessary to

remove the intake manifold to isolate the condition.

4. Ignition OFF, measure the resistance between the appropriate high voltage supply circuit and ground. The DMM should display OL ohm.

瀚慖f less than the specified range, test the high voltage supply circuit and the high voltage control circuit for a short to ground. If the

circuits/connections test normal, test or replace the appropriate Q17 fuel injector(s).

5. Test for 2-3 ohm between the appropriate high voltage supply circuit and high voltage control circuit.

Sunday, December 6, 2020

2010 Cadillac Truck SRX AWD V6-3.0L Page 892

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)

Description and Operation

ABS Description and Operation (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Description and Operation)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning)for scan tool information

Circuit/System Verification

Ignition ON, observe the scan tool EBCM Wheel Speed Sensor parameters. The reading should be the same speed on all sensors when driving in a

straight line at a speed greater than 20 km/h (13 MPH).

Circuit/System Testing

1. Ignition ON, verify that DTC C0035, C0040, C0045, or C0050 is not present in the EBCM.

瀚慖f any listed DTC is present, refer to DTC C0035, C0040, C0045, or C0050 (See: C Code Charts/C0035) to diagnose that DTC prior to

this diagnostic.

2. Replace the K17 Electronic Brake Control Module (EBCM) and verify the DTC does not reset.

瀚慖f the DTC resets, replace the module that set the DTC.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

Control Module References (See: Testing and Inspection/Programming and Relearning)for module replacement, setup and programming

C1223

DTC C1207-C1210, C1221-C1228, or C1232-C1235

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions)provides an overview of each diagnostic category.

DTC Descriptor

DTC C1207 00

- Left Front Wheel Speed Sensor Circuit High Input Malfunction

DTC C1208 00

- Right Front Wheel Speed Sensor Circuit High Input Malfunction

DTC C1209 00

- Left Rear Wheel Speed Sensor Circuit High Input Malfunction

DTC C1210 00

- Right Rear Wheel Speed Sensor Circuit High Input Malfunction

2010 Cadillac Truck SRX AWD V6-3.0L Page 331

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)

Description and Operation

Steering Wheel and Column Description and Operation (See: Steering and Suspension/Steering/Steering Column/Description and Operation)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

Clear all DTCs and operate the steering column lock within the conditions for running the DTC. The DTC should not set.

If the DTC sets, replace the K60 Steering Column Lock Control Module or the K9 Body Control Module.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Steering Column Lock Control Module Replacement (ULS) (See: Steering and Suspension/Steering/Steering Column/Steering Column

Lock/Service and Repair)

* Body Control Module Replacement (See: Body and Frame/Body Control Systems/Body Control Module/Service and Repair/Body Control

Module Replacement)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for steering column lock control module/body

control module replacement, setup and programming

B310D

DTC B310D-B310F

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions)provides an overview of each diagnostic category.

DTC Descriptors

DTC B310D 00

- Keyless Entry Transmitter 6 Battery

DTC B310E 00

- Keyless Entry Transmitter 7 Battery

DTC B310F 00

- Keyless Entry Transmitter 8 Battery

Circuit/System Description

With each press of a keyless entry transmitter button, a message containing the current battery state of the transmitter is sent to the remote control

door lock receiver, along with the commanded keyless entry function. The remote control door lock receiver sends this to the body control module

(BCM) to perform the requested function.

Conditions for Running the DTC

Friday, November 27, 2020

2010 Cadillac Truck SRX AWD V6-3.0L Page 813

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)

Description and Operation

Brake Assist System Description and Operation (See: Brakes and Traction Control/Hydraulic System/Description and Operation/Brake Assist

System)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning)

Circuit/System Testing

1. Ignition ON, verify that DTC C1100 is not present.

瀚慖f DTC C1100 is present, refer to DTC C1100 (See: C Code Charts/C1100).

2. Inspect the brake booster vacuum system for damage, leakage and correct installation. Refer to Brake Assist System Diagnosis (See: Brakes

and Traction Control/Hydraulic System/Testing and Inspection/Component Tests and General Diagnostics/Brake Assist System Diagnosis).

3. If the brake booster vacuum systems diagnoses normal, replace the B19B Brake Booster Vacuum Sensor and verify the DTC does not reset.

If the DTC resets, replace the K17 Electronic Brake Control Module (EBCM).

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests)

* Power Brake Booster Vacuum Sensor Replacement (See: Brakes and Traction Control/Power Brake Assist/Brake Booster Vacuum

Sensor/Service and Repair)

* Control Module References (See: Testing and Inspection/Programming and Relearning)

C0393

DTC C0393

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptor

DTC C0393 0B

- Rear Axle Coupling Solenoid Valve Control Circuit High Current

Diagnostic Fault Information

Circuit/System Description

The rear differential clutch solenoid valve is mounted on the rear of the differential housing. The rear differential clutch control module supplies

Monday, November 23, 2020

2010 Cadillac Truck SRX AWD V6-3.0L Page 969