2010 Cadillac Truck SRX FWD V6-3.0L Page 1936
瀚慖f not the specified value, replace the Q6 Camshaft Position Actuator Solenoid Valve.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Camshaft Position Actuator Solenoid Valve Solenoid Replacement - Bank 1 (Right Side) Intake (See: Engine, Cooling and
Exhaust/Engine/Actuators and Solenoids - Engine/Variable Valve Timing Solenoid/Service and Repair/Camshaft Position Actuator Solenoid
Valve Solenoid Replacement - Bank 1 (Right Side) Intake)
* Camshaft Position Actuator Solenoid Valve Solenoid Replacement - Bank 1 (Right Side) Exhaust (See: Engine, Cooling and
Exhaust/Engine/Actuators and Solenoids - Engine/Variable Valve Timing Solenoid/Service and Repair/Camshaft Position Actuator Solenoid
Valve Solenoid Replacement - Bank 1 (Right Side) Exhaust)
* Camshaft Position Actuator Solenoid Valve Solenoid Replacement - Bank 2 (Left Side) Intake (See: Engine, Cooling and
Exhaust/Engine/Actuators and Solenoids - Engine/Variable Valve Timing Solenoid/Service and Repair/Camshaft Position Actuator Solenoid
Valve Solenoid Replacement - Bank 2 (Left Side) Intake)
* Camshaft Position Actuator Solenoid Valve Solenoid Replacement - Bank 2 (Left Side) Exhaust (See: Engine, Cooling and
Exhaust/Engine/Actuators and Solenoids - Engine/Variable Valve Timing Solenoid/Service and Repair/Camshaft Position Actuator Solenoid
Valve Solenoid Replacement - Bank 2 (Left Side) Exhaust)
* Control Module References (See: Testing and Inspection/Programming and Relearning) for Engine Control Module replacement, setup, and
programming
P2096
DTC P2096
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptor
DTC P2096
- Post Catalyst Fuel Trim System Low Limit
Circuit Description
Fuel trim bias is used by the engine control module (ECM) to keep the post catalyst HO2S voltage within a range of 580-665 mV. This allows
optimal catalyst efficiency under light load conditions, such as at idle or a steady cruise. The ECM constantly monitors how lean or rich the fuel
trim bias is commanded, to determine if the fuel trim bias is greater than a calibrated amount.
Conditions for Running the DTC
* Before the ECM can report DTC P2096, DTCs P0030, P0031, P0032, P0130, P0131, P0132, P0133, P0135, P0137, P0138, P0140, P0141,
P2232, P2235, P2270, P2271, P2272, and P2273 must run and pass.
* DTC P0100, P0101, P0102, P0103, P0111, P0112, P0113, P0116, P0117, P0118, P0119, P0420, P0443, P0458, or P0459 is not set.
* The engine speed is 1,080-3,480 RPM.
* The engine load is 17-20 % and steady.
* The Closed Loop fuel control is active for greater than 1 s.
* The front and rear HO2S are in Closed Loop.
* The calculated exhaust gas temperature is greater than 250掳C (482掳F).
* DTC P2096 runs continuously when the conditions above have been met for greater than 200 s.
Conditions for Setting the DTC
The lean correction limit for a condition causing a rich air/fuel mixture has been exceeded for a predetermined amount of time. The condition exists
for greater than 4 s or for a cumulative of 30 s.
Action Taken when the DTC Sets
DTC P2096 is a Type B DTC.
Conditions for Clearing the MIL/DTC
