2010 Cadillac Truck SRX FWD V6-3.0L Page 1097
If the electrical circuit tests are OK and the shift pattern is not occurring, there may be a mechanical/hydraulic condition that prevents operation.
Refer to Symptoms - Automatic Transmission (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing and
Inspection/Symptom Related Diagnostic Procedures/6T70/6T75 - Automatic Transmission/Symptoms - Automatic Transmission).
Reference Information
Schematic Reference
Automatic Transmission Controls Schematics (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Diagrams)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
Description and Operation
Electronic Component Description (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Description and Operation/6T70/6T75 -
Automatic Transmission/Electronic Component Description)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Verification
With a scan tool observe the Tow/Haul switch parameter in Body Controls data list. With the ignition On or engine running, operate the Tow/Haul
switch several times, and observe the parameter as you operate the switch. The parameter should toggle between Active and Inactive when the
switch is operated.
Circuit/System Testing
1. Ignition Off, transmission in Park, disconnect the Tow/Haul switch connector.
2. Test for less than 1 ohm of resistance between the Tow/Haul switch signal circuit terminal B and ground.
瀚慖f greater than the specified range, test the ground circuit for an open/high resistance.
3. Ignition On, verify the scan tool Tow/Haul parameter displays Inactive.
瀚慖f not the specified value, test the signal circuit for a short to ground. If the circuit tests normal, replace the BCM.
4. Install a fused jumper between the signal circuit and ground. Verify the scan tool parameter displays Active.
瀚慖f not the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the
BCM.
5. If all circuits test normal, replace the Tow/Haul switch.
6. If the electrical circuit checks are OK and the tow/haul shift pattern is not occurring, there may be a mechanical/hydraulic condition that
prevents tow/haul operation. Refer to Symptoms - Automatic Transmission (See: Transmission and Drivetrain/Automatic
Transmission/Transaxle/Testing and Inspection/Symptom Related Diagnostic Procedures/6T70/6T75 - Automatic Transmission/Symptoms -
Automatic Transmission).
Component Testing
Verify the Tow/Haul Mode parameter on the scan tool while cycling the tow/haul switch.
1. Ignition Off, transmission in Park, disconnect the transmission Tow/Haul switch assembly.
2. Test for infinite resistance between the Tow/Haul switch with the switch in the Open position.
