2010 Cadillac Truck SRX FWD V6-3.0L Page 1054
Systems/Oxygen Sensor/Service Precautions/Heated Oxygen Sensor Resistance Learn Reset Caution).
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 (LF1) (See: Powertrain Management/Computers and Control Systems/Oxygen
Sensor/Service and Repair/Heated Oxygen Sensor Replacement - Bank 1 Sensor 1)
* Heated Oxygen Sensor Replacement - Bank 1 Sensor 2 (LF1) (See: Powertrain Management/Computers and Control Systems/Oxygen
Sensor/Service and Repair/Heated Oxygen Sensor Replacement - Bank 1 Sensor 2)
* Heated Oxygen Sensor Replacement - Bank 2 Sensor 1 (LF1) (See: Powertrain Management/Computers and Control Systems/Oxygen
Sensor/Service and Repair/Heated Oxygen Sensor Replacement - Bank 2 Sensor 1)
* Heated Oxygen Sensor Replacement - Bank 2 Sensor 2 (LF1) (See: Powertrain Management/Computers and Control Systems/Oxygen
Sensor/Service and Repair/Heated Oxygen Sensor Replacement - Bank 2 Sensor 2)
* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming
P050D
DTC P050D
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptor
DTC P050D
- Cold Start Rough Idle
Circuit/System Description
During a cold start, the engine control module (ECM) commands dual-pulse mode during Open Loop operation to improve cold start emissions. In
dual-pulse mode, the injectors are energized twice during each injection event. As with misfire diagnosis, in dual-pulse mode the ECM monitors the
crankshaft position sensor and the camshaft position sensors to calculate crankshaft rotation speed. In normal operation, optimum fuel delivery
during dual-pulse mode produces a steady crankshaft rotation speed. If the variations exceed a calibrated value, the code will be set.
Conditions for Running the DTC
* DTCs P0010, P0011, P0013, P0014, P0016, P0017, P0018, P0019, P0020, P0021, P0023, P0024, P0089, P0090-P0092, P00C6, P00C8,
P00C9, P00CA, P0101-P0103, P0106-P0108, P0112-P0114, P0116-P0118, P0121-P0123, P0128, P0192, P0193, P0201-P0206, P0222,
P0223, P0261, P0262, P0264, P0265, P0267, P0268, P0270, P0271, P0273, P0274, P0276, P0277, P0315, P0335, P0336, P0351-P0356,
P0627-P0629, P069E, P0716, P0717, P0722, P0723, P0850-P0852, P1248, P1249, P124A, P124B, P124C, P124D, P1258, P135A, P135B,
P150C, P163A, P1762, P1763, P1915, P2122, P2123, P2127, P2128, P2135, P2138, P2147, P2148, P2150, P2151, P2153, P2154, P2156,
P2157, P216B, P216C, P216E, P216F, P228C, P228D, U0109 are not set.
* The catalyst temperature is less than 100掳C (212掳F).
* The engine coolant temperature is warmer than 10掳C (14掳F).
* The barometric pressure is greater than 70 kPa.
* The engine speed is between 450-1800 RPM.
* The engine is running and a cold start has been detected.
* DTC P050D runs once per cold start.
Conditions for Setting the DTC
This DTC will set if the ECM detects variations in crankshaft rotation speed caused by the lack of adequate fuel delivery during dual-pulse mode.
Action Taken When the DTC Sets
* DTC P050D is a Type B DTC.
* The ECM disables dual pulse mode and energizes the fuel injector as it would for a warm engine.
Conditions for Clearing the DTC
DTC P050D is a Type B DTC.
