Saturday, October 30, 2021

2010 Cadillac Truck SRX FWD V6-3.0L Page 1086

2010 Cadillac Truck SRX FWD V6-3.0L Page 1086



Conditions for Clearing the DTC



* DTCs P0601, P0602, P0603, P0604, P0606, P062B, P062F, P0630 and P16F3 are Type A DTCs.



* DTC P2610 is a Type B DTC.



Diagnostic Aids



Low voltage or a momentary loss of power or ground to the ECM may cause a DTC to set. Verify for the following:



* The battery cables are clean and tight, and the battery is fully charged-Refer to Battery Inspection/Test (See: Starting and Charging/Testing



and Inspection/Component Tests and General Diagnostics/Battery Inspection/Test).



* The ECM ground circuits do not have an open or high resistance



* The ECM power circuits do not have an open, short to ground, or high resistance



Reference Information



Schematic Reference



Engine Controls Schematics (LAU) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics



(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)



Connector End View Reference



Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)



Electrical Information Reference



* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit



Testing/Circuit Testing)



* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic



Procedures/Connector Repairs/Connector Repairs)



* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General



Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)



* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring



Repairs/Wiring Repairs)



DTC Type Reference



Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code



(DTC) Type Definitions)



Scan Tool Reference



Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information



Circuit/System Verification



1. Observe the DTC information with a scan tool. DTC P0601, P0602, P0603, P0604, P0606, P062B, P062F, P0630, P16F3, or P2610 should



not set.



2. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the



conditions that you observed from the Freeze Frame/Failure Records data.



Circuit/System Testing



1. Ignition ON, clear the DTC information with a scan tool.



2. Observe the scan tool DTC information. Verify that DTC P0602 or P0630 does not set.



瀚慖f DTC P0602 or P0630 failed this ignition, reprogram the K20 ECM. Refer to Control Module References (See: Testing and



Inspection/Programming and Relearning). If the DTC resets, replace the K20 ECM.



3. Observe the DTC information with a scan tool. Verify that DTC P0601, P0603, P0604, P0606, P062B, P062F, P16F3, or P2610 does not set.



瀚慖f a DTC failed this ignition, replace the K20 ECM.



Repair Instructions



Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.



Control Module References (See: Testing and Inspection/Programming and Relearning) for engine control module replacement, setup, and