2010 Cadillac CTS Sedan AWD V6-3.6L Page 870
DTC P000C
- Intake Camshaft Position System Slow Response Bank 2
DTC P000D
- Exhaust Camshaft Position System Slow Response Bank 2
DTC P0011
- Intake Camshaft Position System Performance Bank 1
DTC P0014
- Exhaust Camshaft Position System Performance Bank 1
DTC P0021
- Intake Camshaft Position System Performance Bank 2
DTC P0024
- Exhaust Camshaft Position System Performance Bank 2
Circuit/System Description
The camshaft position actuator system enables the Engine Control Module (ECM) to change the timing of the camshafts while the engine is
operating. The camshaft position actuator solenoid signal from the ECM is pulse width modulated (PWM). The ECM controls the camshaft position
actuator solenoid duty cycle by controlling the amount of solenoid ON time. The camshaft position actuator solenoid controls the advance or the
retard of each camshaft. The camshaft position actuator solenoid controls the oil flow that applies the pressure to advance or retard the camshafts.
Conditions for Running the DTC
* Before the ECM can report DTC P000A, P000B, P000C, P000D, P0011, P0014, P0021, or P0024 failed, DTCs P0010, P0013, P0020,
P0023, P0341, P0342, P0343, P0346, P0347, P0348, P0366, P0367, P0368, P0391, P0392, P0393, P2088, P2089, P2090, P2091, P2092,
P2093, P2094, and P2095 must run and pass.
* DTC P0016, P0017, P0018, P0019, P0335, P0336, or P0338 is not set.
* The engine is operating for greater than 1 seconds.
* The engine speed is greater than 520 RPM.
* The engine must accelerate such that the CMP actuator system is commanded from the park position to the phased position. This is
considered a cam control cycle. There must be a minimum of 2 cam control cycles for at least 2.5 seconds each in the phased position.
* DTCs P000A, P000B, P000C, P000D, P0011, P0014, P0021, and P0024 run continuously once the above conditions are met for greater than
600 seconds.
Conditions for Setting the DTC
* The ECM detects the difference between the desired camshaft position angle and the actual camshaft position angle is greater than 7-8
degrees.
OR
* The ECM detects a slow response, a deviation greater than 1.5 degrees in time greater than 2 seconds, for the actual camshaft position angle
to match the desired position angle during the test.
* Either condition exists for greater than 1 second or a cumulative of 10 seconds.
Action Taken When the DTC Sets
DTCs P000A, P000B, P000C, P000D, P0011, P0014, P0021, and P0024 are type B DTCs.
Conditions for Clearing the DTC
DTCs P000A, P000B, P000C, P000D, P0011, P0014, P0021, and P0024 are type B DTCs.
Reference Information
Schematic Reference
Engine Controls Schematics (LLT) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics
(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Camshaft Actuator System Description (See: Powertrain Management/Computers and Control Systems/Description and Operation/Camshaft
Actuator System Description)
Electrical Information Reference
