Friday, April 23, 2021

2010 Cadillac CTS Sedan AWD V6-3.6L Page 176

2010 Cadillac CTS Sedan AWD V6-3.6L Page 176



affected component/connector:



* The impact sensor



* The SDM



* The impact sensor wiring harness connector



* The SDM wiring harness connector



1. Ignition OFF, disconnect the harness connector at the appropriate impact sensor and the harness connector at the SDM.



2. Test for infinite resistance between the signal circuit terminal B and ground.



瀚慖f less than the specified range, test the signal circuit for a short to ground.



3. Ignition ON, test for less than 1 V between the signal circuit terminal B and ground.



瀚慖f greater than the specified range, test the circuit for a short to voltage.



4. Test for less then 1 ohm between the appropriate low reference circuit terminal at the sensor and the appropriate low reference circuit



terminal at the SDM:



* Left Front Sensor - Low Reference circuit terminal 2 at the sensor and the low reference circuit terminal 24 X2 at the SDM.



* Right Front End Sensor - Low Reference circuit terminal 2 at the sensor and the low reference circuit terminal 25 X2 at the SDM.



* Left Front Side Sensor - Low Reference circuit terminal 1 at the sensor and the low reference circuit terminal 19 X2 at the SDM.



* Right Front Side Sensor - Low Reference circuit terminal 1 at the sensor and the low reference circuit terminal 22 X2 at the SDM.



* Left Rear Side Sensor - Low Reference circuit terminal 2 at the sensor and the low reference circuit terminal 28 X2 at the SDM.



* Right Rear Side Sensor - Low Reference circuit terminal 2 at the sensor and the low reference circuit terminal 29 X2 at the SDM.



瀚慖f greater than the specified range, test the circuit for an open/high resistance.



5. Test for less then 1 ohm between the appropriate signal circuit terminal at the sensor and the appropriate signal circuit terminal at the SDM:



* Left Front Sensor - Signal circuit terminal 1 at the sensor and the signal circuit terminal 23 X2 at the SDM.



* Right Front End Sensor - Signal circuit terminal 1 at the sensor and the signal circuit terminal 26 X2 at the SDM.



* Left Side Sensor - Signal circuit terminal 2 at the sensor and the signal circuit terminal 20 X2 at the SDM.



* Right Side Sensor - Signal circuit terminal 2 at the sensor and the signal circuit terminal 21 X2 at the SDM.



* Left Rear Side Sensor - Signal circuit terminal 1 at the sensor and the signal circuit terminal 27 X2 at the SDM.



* Right Rear Side Sensor - Signal circuit terminal 1 at the sensor and the signal circuit terminal 30 X2 at the SDM.



瀚慖f greater than the specified range, test the circuit for an open/high resistance.



6. If all circuits test normal, replace the impact sensor.



7. Clear DTCs and operate the vehicle within the condition for running the DTC. Verify DTC B0083, B0084, B0085, B0086, B0087, or B0088



does not set.



瀚慖f any of the DTCs set, replace the SDM.



Repair Instructions



Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.



* SIR/SRS Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Wiring Repairs/SIR/SRS Wiring Repairs)



* Inflatable Restraint Front End Sensor Replacement (See: Restraints and Safety Systems/Air Bag Systems/Impact Sensor/Service and



Repair/Inflatable Restraint Front End Sensor Replacement)



* Inflatable Restraint Side Impact Sensor Replacement - Front Side Door (See: Restraints and Safety Systems/Air Bag Systems/Impact



Sensor/Service and Repair/Inflatable Restraint Side Impact Sensor Replacement - Front Side Door)



* Inflatable Restraint Side Impact Sensor Replacement - Rear Side Door (See: Restraints and Safety Systems/Air Bag Systems/Impact



Sensor/Service and Repair/Inflatable Restraint Side Impact Sensor Replacement - Rear Side Door)



* Control Module References (See: Testing and Inspection/Programming and Relearning)for SDM replacement, setup, and programming



B0099



DTC B0099



Diagnostic Instructions



* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System



Check - Vehicle) prior to using this diagnostic procedure.



* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an



overview of the diagnostic approach.



* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure



Instructions) provides an overview of each diagnostic category.