2010 Cadillac CTS Sedan AWD V6-3.6L Page 256
Make sure the object alarm sensors located on the rear vehicle bumper are clear. Remove any snow, mud or ice that may be blocking the sensors.
Reference Information
Schematic Reference
Object Detection Schematics (See: Accessories and Optional Equipment/Collision Avoidance and Parking Assist Systems/Diagrams/Electrical
Diagrams)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Object Detection Description and Operation (UD7 with Display) (See: Accessories and Optional Equipment/Collision Avoidance and Parking
Assist Systems/Description and Operation/Object Detection Description and Operation (UD7 with Display))Object Detection Description and
Operation (UD7 Audio Only) (See: Accessories and Optional Equipment/Collision Avoidance and Parking Assist Systems/Description and
Operation/Object Detection Description and Operation (UD7 Audio Only))Object Detection Description and Operation (B3T) (See: Accessories
and Optional Equipment/Collision Avoidance and Parking Assist Systems/Description and Operation/Object Detection Description and Operation
(B3T))Object Detection Description and Operation (UVC) (See: Accessories and Optional Equipment/Collision Avoidance and Parking Assist
Systems/Description and Operation/Object Detection Description and Operation (UVC))
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit Testing/Circuit Testing)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit
Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Wiring Repairs/Wiring Repairs)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Connector Repairs/Connector Repairs)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Verification
1. Verify that DTC B1E3A is not set.
瀚慖f the DTC is set, refer to DTC B1E3A (See: B Code Charts/B1E3A).
2. Verify that DTC B0958 3A, B0959 3A, B0960 3A, or B0961 3A is not set
瀚慖f DTC is set, replace the appropriate object alarm sensor.
3. Transmission in REVERSE, individually place a suitable object behind each sensor. Verify the appropriate scan tool Rear Region parameter
is between Zone 1 and Zone 4.
Circuit/System Testing
Single Object Alarm Sensor DTC Set
1. Ignition OFF, disconnect the harness connector at the appropriate object alarm sensor.
2. Ignition OFF for 30 seconds, test for less than 20 Ohms between the low reference circuit terminal 2 and ground.
瀚慖f greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the rear
object sensor control module.
3. Ignition ON, transmission in REVERSE, test for 8.0-9.0 V between the voltage reference circuit terminal 1 and ground.
瀚慖f greater than the specified range, test the voltage reference circuit for a short to voltage. If the circuit tests normal, replace the rear object
sensor control module.
瀚慖f less than the specified range, test the voltage reference circuit for a short to ground or an open/high resistance. If the circuit tests
normal, replace the rear object sensor control module.
4. Ignition OFF, remove the malfunctioning object alarm sensor and swap locations with another properly functioning object alarm sensor.
Connect the harness connector at both sensors.
5. Ignition ON, verify DTC is set for the new location in which the malfunctioning object alarm sensor is installed.
瀚慖f the DTC does not set for the new location, test the signal circuit terminal 3 for a short to voltage, short to ground, or an open/high
resistance. If the circuit tests normal, replace the rear object sensor control module.
6. If the DTC sets for the new location in which the malfunctioning object alarm sensor is installed, replace the appropriate object alarm sensor.
