2010 Cadillac Truck SRX AWD V6-3.0L Page 1435
* DTCs P0324, P0325, P0326, P0327, P0328, P0330, P0331, P0332 P0333, P06B6, and P06B7 are Type B DTCs.
* The ignition timing is retarded to reduce the potential of engine damaging spark knock.
Conditions for Clearing the DTC
DTCs P0324, P0325, P0326, P0327, P0328, P0330, P0331, P0332 P0333, P06B6, and P06B7 are Type B DTCs.
Diagnostic Aids
* Inspect the knock sensor for physical damage. A knock sensor that is dropped or damaged may cause a DTC to set.
* Inspect the knock sensor for proper installation. A knock sensor that is loose or over torqued may cause a DTC to set. The knock sensor
should be free of thread sealant.
* The knock sensor mounting surface should be free of burrs, casting flash, and foreign material.
Reference Information
Schematic Reference
Engine Controls Schematics (LAU) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics
(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)
Description and Operation
Electronic Ignition System Description (See: Powertrain Management/Computers and Control Systems/Description and Operation/Electronic
Ignition System Description)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Verification
1. Engine at operating temperature, all accessories OFF, and engine speed greater than 2,000 RPM, observe the Knock Retard and Total Knock
Retard parameters. The parameters should be 0掳.
2. Engine idling, move the related harnesses and connectors for the KS circuits while observing the scan tool Knock Retard and Total Knock
Retard parameters. The parameters should remain steady with no abrupt changes.
3. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the
conditions that you observed from the Freeze Frame/Failure Records data.
Circuit/System Testing
Note:
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using these diagnostic procedures.
* If an engine mechanical noise can be heard, repair the condition before proceeding with this diagnostic. Refer to Symptoms - Engine
Mechanical (See: Engine, Cooling and Exhaust/Engine/Testing and Inspection/Symptom Related Diagnostic Procedures/Symptoms -
Engine Mechanical).
P0324, P0326 and P0331
1. Using a scan tool, verify DTCs P0335 or P0336 are not set.
瀚慖f any of the DTCs are set, diagnose them first. Refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code
Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle).
