2010 Cadillac Truck SRX AWD V6-3.0L Page 1055
* This DTC may be set with a misfire DTC, however the existence of this DTC is a higher priority and indicates the condition to diagnose is
related to fuel and/or injectors, not the ignition/spark system.
* A restricted fuel injector may cause this DTC to set.
* High resistance in the circuits of the injectors could set this DTC without setting an injector DTC. Test the injector circuits of the affected
cylinders for a high resistance if you suspect a condition.
* A drop in system voltage during cold start may set this DTC.
Reference Information
Schematic Reference
Engine Controls Schematics (LAU) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics
(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Testing
Note: Circuit/System Testing requires cold start. Do not start vehicle prior to connecting scan tool and preparing to evaluate the condition during
engine crank.
1. Start the engine and observe the Cylinder 1-4 Current Misfire Counters during the first 500 engine cycles. The Cylinder 1-4 Current Misfire
Counters should not be incrementing.
瀚慖f the misfire counters are incrementing on one or more cylinders, verify that the following conditions do not exist:
* Fuel pressure that is too low or too high-Refer to Fuel System Diagnosis (LF1 China) (See: Powertrain Management/Fuel Delivery and
Air Induction/Fuel Pump/Testing and Inspection/Fuel System Diagnosis (China))Fuel System Diagnosis (LF1 Except China) (See:
Powertrain Management/Fuel Delivery and Air Induction/Fuel Pump/Testing and Inspection/Fuel System Diagnosis (Except China))Fuel
System Diagnosis (LAU China) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Pump/Testing and Inspection/Fuel
System Diagnosis (China))Fuel System Diagnosis (LAU Except China) (See: Powertrain Management/Fuel Delivery and Air
Induction/Fuel Pump/Testing and Inspection/Fuel System Diagnosis (Except China)).
* Contaminated fuel-Refer to Alcohol/Contaminants-in-Fuel Diagnosis (Special Tool) (See: Powertrain Management/Fuel Delivery and
Air Induction/Fuel/Testing and Inspection/Alcohol/Contaminants-in-Fuel Diagnosis (Special Tool))Alcohol/Contaminants-in-Fuel
Diagnosis (Without Special Tool) (See: Powertrain Management/Computers and Control Systems/Testing and Inspection/Component
Tests and General Diagnostics/Alcohol/Contaminants-in-Fuel Diagnosis (Without Special Tool)).
2. If all conditions test normal, replace fuel injectors as indicated by high misfire counts.
Repair Instructions
* Fuel Injection Fuel Rail Assembly Replacement - Bank 1 (LF1) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel
Rail/Service and Repair/Fuel Injection Fuel Rail Assembly Replacement - Bank 1)
* Fuel Injection Fuel Rail Assembly Replacement - Bank 2 (LF1) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel
Rail/Service and Repair/Fuel Injection Fuel Rail Assembly Replacement - Bank 2)
Repair Verification
Note: Repair Verification requires cold start.
1. Ignition ON, engine OFF, clear the DTCs with a scan tool.
