2010 Cadillac Truck SRX AWD V6-3.0L Page 1391
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Spark Plug Replacement (See: Engine, Cooling and Exhaust/Engine/Tune-up and Engine Performance Checks/Spark Plug/Service and
Repair)
* To verify that the performance of the catalytic converter has not been affected by the condition that set this DTC, perform the Repair
Verification for DTC P0420 or P0430. Refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code
Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle) for DTC P0420 or P0430.
P0302
DTC P0300-P0306 (LF1, LFW)
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC P0300
- Engine Misfire Detected
DTC P0301
- Cylinder 1 Misfire Detected
DTC P0302
- Cylinder 2 Misfire Detected
DTC P0303
- Cylinder 3 Misfire Detected
DTC P0304
- Cylinder 4 Misfire Detected
DTC P0305
- Cylinder 5 Misfire Detected
DTC P0306
- Cylinder 6 Misfire Detected
Circuit/System Description
The engine control module (ECM) uses information from the crankshaft position sensor and the camshaft position sensors in order to determine
when an engine misfire is occurring. By monitoring variations in the crankshaft rotation speed for each cylinder, the ECM is able to detect
individual misfire events. A misfire rate that is high enough can cause 3-way catalytic converter damage. The malfunction indicator lamp (MIL)
will flash ON and OFF when the conditions for catalytic converter damage are present. DTCs P0301 through P0306 correspond to cylinders 1
through 6. If the ECM is able to determine that a specific cylinder is misfiring, the DTC for that cylinder will set, and the corresponding fuel
injector is disabled. The ECM will re-enable the fuel injector after 4 crankshaft revolutions when the misfire is not current. The ECM will re-enable
the fuel injector after 8 crankshaft revolutions when the misfire is not current, if the vehicle is equipped with a manual transmission.
Conditions for Running the DTC
* DTC P0010, P0011, P0013, P0014, P0016, P0017, P0018, P0019, P0020, P0021, P0023, P0024, P0068, P0101, P0102, P0103, P0106,
P0107, P0108, P0112, P0113, P0117, P0118, P0120, P0121, P0122, P0123, P0220, P0222, P0223, P0335, P0336, P0606, P0641, P0651,
P1516, P2101, P2122, P2123, P2127, P2128 or P2176 is not set.
* The engine speed is between 450-6,600 RPM.
* The evaporative emissions (EVAP) leak detection is not active.
* The delivered torque signal is greater than 5 % at idle.
* The delivered torque signal is between 6-29 % with the transmission in drive.
* The engine coolant temperature (ECT) is between -7 and +127掳C (+19 and +261掳F).
* The ECM is not receiving a rough road signal.
* The fuel level is greater than 11 %.
* The antilock brake system (ABS) and the traction control system (TCS) are not active or detecting rough road.
