2010 Cadillac CTS Sedan AWD V6-3.6L Page 784
Conditions for Running the DTC
* Before the ECM can report DTC P000A, P000B, P000C, P000D, P0011, P0014, P0021, or P0024 failed, DTCs P0010, P0013, P0020,
P0023, P0341, P0342, P0343, P0346, P0347, P0348, P0366, P0367, P0368, P0391, P0392, P0393, P2088, P2089, P2090, P2091, P2092,
P2093, P2094, and P2095 must run and pass.
* DTC P0016, P0017, P0018, P0019, P0335, P0336, or P0338 is not set.
* The engine is operating for greater than 1 seconds.
* The engine speed is greater than 520 RPM.
* The engine must accelerate such that the CMP actuator system is commanded from the park position to the phased position. This is
considered a cam control cycle. There must be a minimum of 2 cam control cycles for at least 2.5 seconds each in the phased position.
* DTCs P000A, P000B, P000C, P000D, P0011, P0014, P0021, and P0024 run continuously once the above conditions are met for greater than
600 seconds.
Conditions for Setting the DTC
* The ECM detects the difference between the desired camshaft position angle and the actual camshaft position angle is greater than 7-8
degrees.
OR
* The ECM detects a slow response, a deviation greater than 1.5 degrees in time greater than 2 seconds, for the actual camshaft position angle
to match the desired position angle during the test.
* Either condition exists for greater than 1 second or a cumulative of 10 seconds.
Action Taken When the DTC Sets
DTCs P000A, P000B, P000C, P000D, P0011, P0014, P0021, and P0024 are type B DTCs.
Conditions for Clearing the DTC
DTCs P000A, P000B, P000C, P000D, P0011, P0014, P0021, and P0024 are type B DTCs.
Reference Information
Schematic Reference
Engine Controls Schematics (LLT) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics
(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Camshaft Actuator System Description (See: Powertrain Management/Computers and Control Systems/Description and Operation/Camshaft
Actuator System Description)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit
Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Wiring Repairs/Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Special Tools
* J 35616-200 - Test Lamp Kit
* For equivalent regional tools, refer to Special Tools (See: Powertrain Management/Computers and Control Systems/Tools and Equipment).
Diagnostic Aids
* The engine oil condition has a major impact on the camshaft actuator system.
* A low oil level condition may set this DTC. The engine may require an oil change. Inquire with the customer when the last oil change was
performed. You may also monitor the scan tool Engine Oil Life parameter. Advise the customer an oil change may be required.
* Inspect the engine for any recent engine mechanical repairs. An incorrectly installed camshaft, camshaft actuator, or timing chain can cause
