2010 Cadillac Truck SRX AWD V6-3.0L Page 1390
3. Observe the scan tool Misfire Current Cyl. 1-6 parameters. The Misfire Current Counters should not be incriminating.
4. Engine idling, perform the cylinder power balance test with a scan tool to isolate the misfiring cylinder. The engine speed should change
when each injector is disabled.
5. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the
conditions that you observed from the Freeze Frame/Failure Records data.
Circuit/System Testing
1. Verify that the following conditions do not exist:
* Vacuum hose splits, kinks, and incorrect connections
* Engine vacuum leaks
* Crankcase ventilation system for vacuum leaks
* Fuel pressure that is too low or too high-Refer to Fuel System Diagnosis (LF1 China) (See: Powertrain Management/Fuel Delivery and
Air Induction/Fuel Pump/Testing and Inspection/Fuel System Diagnosis (China))Fuel System Diagnosis (LF1 Except China) (See:
Powertrain Management/Fuel Delivery and Air Induction/Fuel Pump/Testing and Inspection/Fuel System Diagnosis (Except China))Fuel
System Diagnosis (LAU China) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Pump/Testing and Inspection/Fuel
System Diagnosis (China))Fuel System Diagnosis (LAU Except China) (See: Powertrain Management/Fuel Delivery and Air
Induction/Fuel Pump/Testing and Inspection/Fuel System Diagnosis (Except China)).
* Contaminated Fuel-Refer to Alcohol/Contaminants-in-Fuel Diagnosis (Special Tool) (See: Powertrain Management/Fuel Delivery and
Air Induction/Fuel/Testing and Inspection/Alcohol/Contaminants-in-Fuel Diagnosis (Special Tool))Alcohol/Contaminants-in-Fuel
Diagnosis (Without Special Tool) (See: Powertrain Management/Computers and Control Systems/Testing and Inspection/Component
Tests and General Diagnostics/Alcohol/Contaminants-in-Fuel Diagnosis (Without Special Tool)).
* Exhaust system restrictions
瀚慖f you find any of the above conditions, repair as necessary.
2. Ignition OFF, remove the T8 ignition coil of the misfiring cylinder, but leave the electrical connector connected.
3. Inspect the ignition coil boot for the following conditions:
* Holes
* Tears
* Carbon tracking
* Oil contamination
* water intrusion
瀚慖f you find any of the above conditions, repair as necessary.
4. Install the J 26792 - Spark Tester to the boot of the appropriate T8 ignition coil and ground.
Note: An erratic or weak spark is considered a no spark condition.
5. Attempt to start the engine and observe the J 26792 - Spark Tester. The spark tester should spark.
瀚慖f there is no spark, refer to Electronic Ignition System Diagnosis (See: Powertrain Management/Computers and Control
Systems/Testing and Inspection/Component Tests and General Diagnostics/Electronic Ignition System Diagnosis) for diagnosis of the
ignition coil.
6. Ignition OFF, remove the spark plug from the misfiring cylinder. Verify that the spark plug does not exhibit the following conditions:
* Gas, coolant, or oil fouled-Refer to Spark Plug Inspection (See: Engine, Cooling and Exhaust/Engine/Tune-up and Engine Performance
Checks/Spark Plug/Testing and Inspection).
* Cracked, worn, incorrectly gapped-Refer to Ignition System Specifications (LAU) (See: Powertrain Management/Ignition
System/Specifications)Ignition System Specifications (LF1) (See: Powertrain Management/Ignition System/Specifications).
瀚慖f there is a condition with the spark plug, replace the spark plug.
7. Exchange the suspected spark plug with another cylinder that is operating correctly.
8. Engine idling, observe the scan tool Misfire Current Counter parameters. The misfire should not follow the spark plug exchange.
瀚慖f the misfire follows the spark plug, replace the spark plug.
9. If all conditions test normal, test or inspect for the following:
* A lean or rich Q17 fuel injector-Refer to Fuel Injector Solenoid Coil Test (LAU) (See: Powertrain Management/Fuel Delivery and Air
Induction/Fuel Injector/Testing and Inspection)Fuel Injector Solenoid Coil Test (LF1, LFW) (See: Powertrain Management/Fuel
Delivery and Air Induction/Fuel Injector/Testing and Inspection).
* An engine mechanical condition-Refer to Symptoms - Engine Mechanical (See: Engine, Cooling and Exhaust/Engine/Testing and
Inspection/Symptom Related Diagnostic Procedures/Symptoms - Engine Mechanical).
