2010 Cadillac Truck SRX AWD V6-3.0L Page 1059
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC P052B
- Cold Start Intake Camshaft Position System Performance Bank 1 - Retarded
DTC P052D
- Cold Start Intake Camshaft Position System Performance Bank 2 - Retarded
DTC P054B
- Cold Start Exhaust Camshaft Position System Performance Bank 1 - Retarded
DTC P054D
- Cold Start Exhaust Camshaft Position System Performance Bank 2 - Retarded
Circuit/System Description
The camshaft position actuator system enables the Engine Control Module (ECM) to change the timing of the camshafts while the engine is
operating. The camshaft position actuator solenoid signal from the ECM is pulse width modulated (PWM). The ECM controls the camshaft position
actuator solenoid duty cycle by controlling the amount of solenoid ON time. The camshaft position actuator solenoid controls the advance or the
retard of each camshaft. The camshaft position actuator solenoid controls the oil flow that applies the pressure to advance or retard the camshafts.
Conditions for Running the DTC
* Before the ECM can report DTC P052B, P052D, P054B, or P054D failed, DTCs P0010, P0013, P0020, P0023, P0341, P0342, P0343,
P0346, P0347, P0348, P0366, P0367, P0368, P0391, P0392, P0393, P2088, P2089, P2090, P2091, P2092, P2093, P2094, and P2095 must
run and pass.
* DTC P0010, P0013, P0016, P0017, P0018, P0019, P0020, P0023, P0335, P0336, P0338, P2088, P2089, P2090, P2091, P2092, P2093,
P2094, and P2095 is not set.
* The engine speed is greater than 560 RPM.
* The engine is operating for greater than 1 s.
* The engine coolant temperature is between -48 to +143掳C (-54 to +289掳F).
* The engine oil temperature is between -48 to +180掳C (-54 to +356掳F).
* The engine must accelerate such that the camshaft position actuator system is commanded from the park position to the phased position. This
is considered a cam control cycle. There must be a minimum of 2 cam control cycles for at least 2.5 s each in the phased position.
* DTCs P052B, P052D, P054B, and P054D run continuously once the above conditions are met for greater than 20 s.
Conditions for Setting the DTC
* The ECM detects the difference between the desired camshaft position angle and the actual camshaft position angle is greater than 6 degrees.
* The condition exists for greater than 1 s or for a cumulative of 4 s.
Action Taken When the DTC Sets
DTCs P052B, P052D, P054B, and P054D are type B DTCs.
Conditions for Clearing the DTC
DTCs P052B, P052D, P054B, and P054D are type B DTCs.
Reference Information
Schematic Reference
Engine Controls Schematics (LAU) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics
(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)
Description and Operation
Camshaft Actuator System Description (See: Powertrain Management/Computers and Control Systems/Description and Operation/Camshaft
Actuator System)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
