2010 Cadillac Truck SRX AWD V6-3.0L Page 1475
injection points of the engine. The ECM uses the cylinder 1 intake camshaft position sensor to determine injector and ignition system
synchronization. Also, the cylinder 1 intake camshaft position sensor is used to determine camshaft to crankshaft relationship, to control camshaft
phasing, and for limp-home operation.
Conditions for Running the DTC
* DTCs P0335, P0336, P0641, P0651, or P0697 are not set.
* The engine is cranking or running.
* The DTC runs continuously when the above conditions are met.
Conditions for Setting the DTC
* The ECM detects that the engine has started, but has received either of the following during the first engine revolution:
- Less than or more than 4 camshaft position sensor pulses, if equipped with an automatic transmission
- Less than 4 or more than 8 camshaft position sensor pulses, if equipped with a manual transmission
* The ECM detects that the engine is running, but receives less than 398 camshaft position or more than 402 camshaft position sensor pulses
per 100 engine cycles in 800 of 1000 engine cycles.
Action Taken When the DTC Sets
* DTCs P0341, P0346, P0366, and P0391 are Type B DTCs.
* The camshaft position actuator is commanded to the Home or Parked position.
* The ignition system defaults to a failed camshaft position sensor based on the crankshaft position sensor.
Conditions for Clearing the MIL/DTC
* DTCs P0341, P0346, P0366, and P0391 are Type B DTCs.
* With a DTC set, the engine may crank for an extended period of time at start-up.
Diagnostic Aids
* With a DTC set, the engine may crank for an extended period of time at start-up.
* The cylinder 1 intake camshaft position sensor is used for injector and ignition system synchronization. A stalling condition will occur if the
CMP sensor signal is intermittent and a DTC will not set. Inspect all cylinder 1 intake camshaft position sensor circuits for poor connections.
Reference Information
Schematic Reference
Engine Controls Schematics (LAU) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics
(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)
Description and Operation
Electronic Ignition System Description (See: Powertrain Management/Computers and Control Systems/Description and Operation/Electronic
Ignition System Description)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Engine Control Module Scan Tool Information (LF1,LFW) (See: Powertrain Management/Computers and Control Systems/Testing and
Inspection/Scan Tool Testing and Procedures)Engine Control Module Scan Tool Information (LAU) (See: Powertrain Management/Computers
and Control Systems/Testing and Inspection/Scan Tool Testing and Procedures) for scan tool information
