Friday, July 17, 2020

2010 Cadillac Truck SRX AWD V6-3.0L Page 1255

2010 Cadillac Truck SRX AWD V6-3.0L Page 1255



The ECM detects that the fuel rail fuel pressure sensor signal voltage is high.



Action Taken When the DTC Sets



* DTCs P0192 and P0193 are Type A DTCs.



* A message center or an indicator may display Reduced Engine Power.



Conditions for Clearing the DTC



DTCs P0192 and P0193 are Type A DTCs.



Reference Information



Schematic Reference



Engine Controls Schematics (LAU) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics



(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)



Connector End View Reference



Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)



Description and Operation



Fuel System Description (LF1) (See: Powertrain Management/Fuel Delivery and Air Induction/Description and Operation/Fuel System



Description)Fuel System Description (LAU or LY7) (See: Powertrain Management/Fuel Delivery and Air Induction/Description and



Operation/Fuel System Description)



Electrical Information Reference



* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit



Testing/Circuit Testing)



* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic



Procedures/Connector Repairs/Connector Repairs)



* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General



Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)



* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring



Repairs/Wiring Repairs)



DTC Type Reference



Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code



(DTC) Type Definitions)



Scan Tool Reference



Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information



Circuit/System Verification



1. Ignition ON, observe the DTC information with a scan tool, DTC P0641 should not be set.



瀚慖f a DTC is set, refer to DTC P0641, P0651, P0697, or P06A3 (LF1) (See: P Code Charts/P0641/ECM).



2. Engine idling, observe the DTC information with a scan tool. DTC P0192 or P0193 should not set.



3. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the



conditions that you observed from the Freeze Frame/Failure Records data.



Circuit/System Testing



1. Ignition OFF, disconnect the multi-way harness connector X198 at the rear of the intake manifold.



2. Remove the fuse that supplies B+ to terminal 52-X1 of the K20 ECM.



Note: Testing for steps 3 through 7 is performed on the ECM side of the multi-way harness connector.



3. Ignition OFF, test for less than 5 ohm between the low reference circuit terminal 5 and ground.



瀚慖f greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the K20



ECM.



4. Install the fuse that supplies B+ to terminal 52-X1 of the K20 ECM.



5. Ignition ON, test for 4.8-5.2 V between the 5 V reference circuit terminal 11 and ground.



瀚慖f less than the specified range, test the 5 V reference circuit for a short to ground or an open/high resistance. If the circuit tests normal,